Nanostructure of a poly(acrylic acid) brush and its transition in the amphiphilic diblock copolymer monolayer on the water surface.

The nanostructure and its transition of in a poly(acrylic acid) (PAA) brush in the water surface monolayers of poly(hydrogenated isoprene)-b-poly(acrylic acid) with different block lengths and block ratios were investigated by X-ray reflectivity as a function of surface pressure (brush density) and salt concentration in the subphase. The PAA brush showed the same behavior after salt addition as did the poly(methacrylic acid) (PMAA) brush, which was investigated previously. The brush chains expanded and then shrunk after passing the maximum with increasing added salt concentration.

Sphere-to-rod transition of non-surface-active amphiphilic diblock copolymer micelles: a small-angle neutron scattering study.

Micellization behavior of amphiphilic diblock copolymers with strong acid groups, poly(hydrogenated isoprene)-block-poly(styrenesulfonate), was investigated by small-angle neutron scattering (SANS). We have reported previously (Kaewsaiha, P.; Matsumoto, K.

Salt effect on the nanostructure of strong polyelectrolyte brushes in amphiphilic diblock copolymer monolayers on the water surface.

The nanostructure of a spread monolayer of diblock copolymers of poly(hydrogenated isoprene) and poly(styrenesulfonate) at the air/water interface were studied by in situ X-ray reflectivity as a function of the brush density and salt concentration. When the monolayer was compressed beyond the "critical brush density", its nanostructure changed from a flat, adsorbed "carpet" layer to a "carpet + brush" structure. The critical brush density was found to be about 0.

Nanostructure and transition of a strong polyelectrolyte brush at the air/water interface.

The strong polyelectrolyte layer in the monolayer of ionic amphiphilic diblock copolymers at the air/water interface consists of carpet and brush layers when the brush density is satisfactorily high like that of the weak acid polymer. Also, a drastic structural change was induced by the addition of salt to the brush layer. In this study, the critical brush density for the transition between "carpet-only" and "carpet + brush" structures for the strongly ionic amphiphilic diblock copolymer, poly(hydrogenated isoprepene)-b-poly(styrene sulfonic acid) sodium salt, monolayer was measured by an in situ X-ray reflectivity technique.

Non-surface activity and micellization of ionic amphiphilic diblock copolymers in water. Hydrophobic chain length dependence and salt effect on surface activity and the critical micelle concentration.

We reported previously (Macromolecules 2003, 36, 5321; Langmuir, 2004, 20, 7412) that amphiphilic diblock copolymers having polyelectrolytes as a hydrophilic segment show almost no surface activity but form micelles in water. In this study, to further investigate this curious and novel phenomenon in surface and interface science, we synthesized another water-soluble ionic amphiphilic diblock copolymer poly(hydrogenated isoprene)-b-sodium poly(styrenesulfonate) PIp-h2-b-PSSNa by living anionic polymerization. Several diblock copolymers with different hydrophobic chain lengths were synthesized and the adsorption behavior at the air/water interface was investigated using surface tension measurement and X-ray reflectivity.

Critical brush density for the transition between carpet-only and carpet/brush double-layered structures.

The critical brush density, where transition from carpet-only structure to carpet/brush double-layered structure occurs, was estimated for a weakly ionic amphiphilic diblock copolymer, (diethylsilacyclobutane)34-b-(methacrylic acid)50, monolayer on water by an in situ X-ray reflectivity technique. The brush density in the monolayer was controlled from 0.11 to 0.

Effect of salt concentration on the nanostructure of weak polyacid brush in the amphiphilic polymer monolayer at the air/water interface.

The effect of salt concentration on the nanostructure of a spread monolayer of ionic amphiphilic diblock copolymer, (diethylsilacyclobutane)m-b-(methacrylic acid)n, at the air-water interface was directly investigated by in situ X-ray reflectivity and neutron reflectivity techniques. Previously, we had found that a poly(methacrylic acid) (PMAA) hydrophilic layer under the water was not in the form of a simple polyelectrolyte brush but consisted of a dense carpet upper layer and a diffuse brush lower layer when the hydrophilic chain was long enough. Here we observed this double layer formation in the monolayer in aqueous NaCl solution at a constant surface pressure.

Micellization of non-surface-active diblock copolymers in water. Special characteristics of poly(styrene)-block-poly(styrenesulfonate).

Strongly ionized amphiphilic diblock copolymers of poly(styrene)-b-poly(styrenesulfonate) with various hydrophilic and hydrophobic chain lengths were synthesized by living radical polymerization, and their properties and self-assembling behavior were systematically investigated by surface tension measurement, foam formation, hydrophobic dye solubilization, X-ray reflectivity, dynamic light scattering, small-angle neutron scattering, small-angle X-ray scattering, and atomic force microscope techniques. These copolymer solutions in pure water did not show a decrease of surface tension with increasing polymer concentration. The solutions also did not show foam formation, and no adsorption at the air/water interface was confirmed by reflectivity experiments.

Synthesis and nanostructure of strong polyelectrolyte brushes in amphiphilic diblock copolymer monolayers on a water surface.

We synthesized an ionic amphiphilic diblock copolymer, poly(hydrogenated isoprene)-b-poly(styrenesulfonic acid) (PIp-h2-b-PSS), by living anionic polymerization, and the nanostructure of its monolayer spread on a water surface was directly investigated by the in situ X-ray reflectivity technique. The monolayer of the diblock copolymer on a water surface had a smooth hydrophobic PIp-h2 layer on water and a "carpet"/polymer brush double layer in a hydrophilic sodium polystyrene sulfonate (PSSNa) layer under the water. The surface pressure dependence and PSSNa chain length dependence of the PIp-h2 layer thickness and the brush nanostructure were quantitatively studied.