Microstructural Characterization of Nb/Inconel 601 Interface Obtained in the Explosive Welding Process.

This work presents the microstructure of the cross-section of a newly developed Nb/Inconel 601 weld with particular attention paid to the continuity, morphology of the interface, and the microstructural changes within its vicinity. Both scanning (SEM) and transmission (TEM) electron microscopy techniques are excellent tools to analyze the microstructure that affects both mechanical and corrosion resistance properties of the obtained product. Grain size examination and their orientation together with the character of grain boundaries by the electron backscattered diffraction (EBSD) technique were performed followed by chemical composition determination across the interface with energy-dispersive X-ray spectroscopy (EDS) in SEM.

On the Disintegration of A1050/Ni201 Explosively Welded Clads Induced by Long-Term Annealing.

The paper presents the microstructure and phase composition of the interface zone formed in the explosive welding process between technically pure aluminum and nickel. Low and high detonation velocities of 2000 and 2800 m/s were applied to expose the differences of the welded zone directly after the joining as well as subsequent long-term annealing. The large amount of the melted areas was observed composed of a variety of Al-Ni type intermetallics; however, the morphology varied from nearly flat to wavy with increasing detonation velocity.

Estimation of systematic errors of discrete line approximation by triangular tessellation and marching squares algorithm.

This paper presents methods to calculate the length overestimation errors which are being made when approximating a discrete line by edges of triangular tessellation and marching squares algorithm. The maximum error and its average value are 15.47 % and 10.

Indenting soft samples (hydrogels and cells) with cantilevers possessing various shapes of probing tip.

The identification of cancer-related changes in cells and tissues based on the measurements of elastic properties using atomic force microscopy (AFM) seems to be approaching clinical application. Several limiting aspects have already been discussed; however, still, no data have shown how specific AFM probe geometries are related to the biomechanical evaluation of cancer cells. Here, we analyze and compare the nanomechanical results of mechanically homogenous polyacrylamide gels and heterogeneous bladder cancer cells measured using AFM probes of various tip geometry, including symmetric and non-symmetric pyramids and a sphere.

Superelastic Behavior of Ti-Nb Alloys Obtained by the Laser Engineered Net Shaping (LENS) Technique.

The effect of Nb content on microstructure, mechanical properties and superelasticity was investigated for a series of Ti-xNb alloys, fabricated by the laser engineered net shaping method, using elemental Ti and Nb powders. The microstructure of as-deposited materials consisted of columnar β-phase grains, elongated in the built direction. However, due to the presence of undissolved Nb particles during the deposition process, an additional heat treatment was necessary.

Estimation of systematic errors committed when approximating length of grain boundaries using edges of rectangular or hexagonal grids of EBSD maps.

A method for calculating the overestimation error of grain boundary (GB) length committed when approximating a straight segment of a GB using edges of rectangular or hexagonal grid was given. The relative errors range from 0 % to 41.42 % and from 15.

Biophysical and Biochemical Characteristics as Complementary Indicators of Melanoma Progression.

The multistep character of cancer progression makes it difficult to define a unique biomarker of the disease. Interdisciplinary approaches, combining various complementary techniques, especially those operating at a nanoscale level, potentially accelerate characterization of cancer cells or tissue properties. Here, we study a relation between the surface and biomechanical properties of melanoma cells, measured by mass spectrometry (ToF-SIMS) and atomic force microscopy (AFM).

Growth Kinetics of the Selected Intermetallic Phases in Ni/Al/Ni System with Various Nickel Substrate Microstructure.

Reactivity in nickel⁻aluminum system was examined for two variants of nickel substrates in terms of the size and shape of Ni grains. The microstructure transformation aroused due to the annealing at 720 °C for different annealing times (0.25 to 72 h) was consequently followed.

Computationally-driven engineering of sublattice ordering in a hexagonal AlHfScTiZr high entropy alloy.

Multi-principle element alloys have enormous potential, but their exploration suffers from the tremendously large range of configurations. In the last decade such alloys have been designed with a focus on random solid solutions. Here we apply an experimentally verified, combined thermodynamic and first-principles design strategy to reverse the traditional approach and to generate a new type of hcp Al-Hf-Sc-Ti-Zr high entropy alloy with a hitherto unique structure.

Three-dimensional microstructural characterization of porous cubic zirconia.

A set of cubic zirconia samples were investigated using 3-dimensional electron backscatter diffraction (3D EBSD) to analyze the grain structure, grain boundary networks and pore morphology. 3D EBSD is a variation of conventional EBSD, whereby a focused ion beam (FIB) is used in a dual beam scanning electron microscope (SEM) i.e.