Brightness of AlGaInAs/InP Multimode Diode Lasers with Different Aperture Widths.

A set of semiconductor lasers with different stripe widths is fabricated based on the AlGaInAs/InP heterostructure with an ultra-narrow waveguide. The key characteristics of the lasers (light-current curves (L-I), current-voltage curves (I-V), and spectral and spatial characteristics) are measured, and their dependence on the stripe width is shown. The operating optical power increases from 1.

Selective Area Epitaxy of Highly Strained InGaAs Quantum Wells (980-990 nm) in Ultrawide Windows Using Metalorganic Chemical Vapor Deposition.

We employed the selective-area-epitaxy technique using metalorganic chemical vapor deposition to fabricate and study samples of semiconductor heterostructures that incorporate highly strained InGaAs quantum wells (980-990 nm emission wavelength). Selective area epitaxy of InGaAs quantum wells was performed on templates that had a patterned periodic structure consisting of a window (where epitaxial growth occurred) and a passive mask (where epitaxial growth was suppressed), each with a width of 100 µm for every element. Additionally, a selectively grown potential barrier layer was included, which was characterized by an almost parabolic curvature profile of the surface.

Multiple increase in the radiative efficiency of 1060-nm laser diodes based on heterostructures with tunnel-coupled injection and a single waveguide mode.

An approach aimed at increasing the radiative efficiency in heterostructures operating in a single vertical mode at 1060 nm has been studied. Two types of heterostructures-the STJH (single tunnel junction heterostructure) and DTJH (double tunnel junction heterostructure)-have been developed to obtain the operation of a single waveguide mode of the first and second order, respectively. A multiple increase in the injection efficiency is realized by using tunnel junctions (TJs) embedded in the wide-gap barriers and placed between the active regions.

High-Power Quantum Cascade Lasers Emitting at 8 μm: Technology and Analysis.

In this work, we demonstrate the features of a two-stage epitaxial growth technique and show the results of power and efficiency measurements for three different designs of quantum cascade lasers with a record-high peak power in the 8 μm spectral region. The time-resolved QCL spectral study proves that InP-based upper cladding paired with an InP contact layer provides better heat dissipation and allows one to reach better power characteristics in comparison with InGaAs-based contact, even with short pulse pumping.

Modulator chip based on semiconductor heterostructures with a surface diffraction grating for laser beam steering.

Design parameter optimization of a chip based on a heterostructure with a surface diffraction grating for laser beam angle modulation was carried out. It was found that the widest field of view is achieved at outcoupling angles close to the total internal reflection. The highest energy efficiency is provided by using epitaxy Bragg reflector on the substrate side.

Surface Nanostructuring during Selective Area Epitaxy of Heterostructures with InGaAs QWs in the Ultra-Wide Windows.

Selective area epitaxy (SAE) is widely used in photonic integrated circuits, but there is little information on the use of this technique for the growth of heterostructures in ultra-wide windows. Samples of heterostructures with InGaAs quantum wells (QWs) on GaAs (100) substrates with a pattern of alternating stripes (100-μm-wide SiO mask/100-μm-wide window) were grown using metalorganic chemical vapour deposition (MOCVD). It was found that due to a local change in the growth rate of InGaAs QW in the window, the photoluminescence (PL) spectra measured from the edge to the center of the window exhibited maximum blueshifts of 14 and 19 meV at temperatures of 80 K and 300 K, respectively.

Ultrabroad tuning range (100 nm) of external-cavity continuous-wave high-power semiconductor lasers based on a single InGaAs quantum well.

An external cavity in Littrow configuration based on a reflective diffraction grating and a high-power semiconductor laser based on an asymmetric heterostructure with low optical loss was studied. A continuous-wave optical output power of 13 W with a linewidth of 0.15 nm was achieved for an external-cavity laser.

High peak optical power of 1ns pulse duration from laser diodes - low voltage thyristor vertical stack.

It is shown that the use of low-voltage GaAs/AlGaAs thyristors as high-speed and high-current switches in vertical stacks with semiconductor lasers ensures the efficient generation of high-power ns-duration laser pulses. The lasing and current dynamics in vertical stacks based on laser diode mini bar emitting at 1060 nm and a single as well as a double thyristor switch is studied. The possibility is demonstrated that a laser diode mini bar (with 3 laser emitters) together with a single thyristor switch can generate laser pulses with a peak power of 6 W with a duration of 950 ps and a peak current of 12 A for an operating voltage of 28 V.

Generation of nanosecond and subnanosecond laser pulses by AlGaAs/GaAs laser-thyristor with narrow mesa stripe contact.

Lasers-thyristors with a narrow (20 μm) mesa stripe contact have been studied. It was shown that the laser peak power reaches a value of 2.5 W in the long-pulse mode at a pulse width of 13 ns.

High power CW (16W) and pulse (145W) laser diodes based on quantum well heterostructures.

We suggested and experimentally confirmed the effective method of internal optical loss reduction by high order mode suppression in a separate confinement quantum well laser heterostructure with asymmetric ultra thick waveguide. Manufacturing of InGaAs/GaAs/AlGaAs laser heterostructure with a 1.7 microm-thick asymmetric waveguide allowed attaining super low value of internal optical loss alphai=0.

Acousto-electron interaction in InGaAsP/InP laser heterostructures.

The frequency modulation of the heterolaser radiation under the ultrasonic strain has been found out. The dynamic and static analysis of the spectral parameters change caused by the alternating strain has been fulfilled. A model is proposed for describing the experimental data, and their theoretical analysis is performed.