Coupling ultrasound and membrane filtration for the fractionation of Spirulina platensis sp. and the recovery of phycocyanin and pigment-free proteins.

The cyanobacterium Spirulina platensis was subjected to a fractionation process involving ultrasound-assisted extraction and membrane filtration to obtain a pure phycocyanin fraction and a clarified colorless protein fraction free of chlorophyll and carotenoids. The effects of pressure and power on total protein release were assessed. The retention of the extracted proteins was then assessed by ultrafiltration, with and without ammonium sulfate precipitation.

Impact of thermomechanical pretreatment by twin-screw extrusion on the properties of bio-based materials from sugarcane bagasse obtained by thermocompression.

The aim of this study was to produce binderless materials by thermocompression from lignocellulosic biomass pretreated using twin-screw extrusion. The impact of twin-screw extrusion pretreatment on sugarcane bagasse (SCB) was evaluated, along with the effects of two associated parameters: the liquid-to-solid (L/S) ratio and the screw profile, using three different mechanical shear rates. It was shown that twin-screw extrusion pretreatment resulted in materials with improved properties as compared to those obtained with untreated SCB.

Aqueous Pretreatment of Lignocellulosic Biomass for Binderless Material Production: Influence of Twin-Screw Extrusion Configuration and Liquid-to-Solid Ratio.

This study was carried out to investigate the continuous aqueous pretreatment of sugarcane bagasse (SCB) through twin-screw extrusion for a new integrated full valorization, where the solid residue (extrudate) was used for the production of bio-based materials by thermocompression and the filtrate for the production of high-value-added molecules. Two configurations, with and without a filtration module, were tested and the influence of the SCB composition and structure on the properties of the materials were determined. The impact of the liquid-to-solid (L/S) ratio was studied (0.

Influence of Thermocompression Conditions on the Properties and Chemical Composition of Bio-Based Materials Derived from Lignocellulosic Biomass.

The aim of this study was to assess the influence of thermocompression conditions on lignocellulosic biomasses such as sugarcane bagasse (SCB) in the production of 100% binderless bio-based materials. Five parameters were investigated: pressure applied (7-102 MPa), molding temperature (60-240 °C), molding time (5-30 min), fiber/fine-particle ratio (0/100-100/0) and moisture content (0-20%). These parameters affected the properties and chemical composition of the materials.

Integrating wet stirred-bead milling for Tetraselmis suecica biorefinery: Operating parameters influence and specific energy efficiency.

Stirred bead milling proved to be an efficient cell destruction technique in a biorefinery unit for the extraction of over 95 % of proteins and 60 % of carbohydrates from the green marine microalga Tetraselmis suecica. Optimum conditions, expressed in terms of metabolite yield and energy consumption, were found for average values of bead size and agitator rotation speed. The higher the microalgae concentration, up to 100 g.

Cell destruction level and metabolites green-extraction of Tetraselmis suecica by low and intermediate frequency ultrasound.

Low (20 kHz) and intermediate (100 kHz) frequency ultrasound (US) were studied for their efficiency on cell destruction and metabolites extraction of the microalga T. suecica. This study revealed different levels of cell destruction.

Twin-Screw Extrusion Process to Produce Renewable Fiberboards.

A versatile twin-screw extrusion process to provide an efficient thermo-mechano-chemical pre-treatment on lignocellulosic biomass before using it as source of mechanical reinforcement in fully bio-based fiberboards was developed. Various lignocellulosic crop by-products have already been successfully pre-treated through this process, e.g.

Lignocellulosic Biomass Fractionation by Mineral Acids and Resulting Extract Purification Processes: Conditions, Yields, and Purities.

Fractionation of lignocellulose is a fundamental step in the valorization of cellulose, hemicelluloses, and lignin to produce various sustainable fuels and chemicals. Mineral acid fractionation is one of the most applied process and leads to the solubilization and hydrolysis of cellulose and hemicelluloses, whereas most of the lignin remains insoluble and can be separated from the extract. The obtained monomeric sugars in the acid extract are in solution with salts, sugar degradation products, and phenolic molecules.

Pressurized water extraction of isoflavones by experimental design from soybean flour and Soybean Protein Isolate.

A Doehlert experimental design was conducted and surface response methodology was used to determine the effect of temperature, contact time and solid liquid ratio on isoflavone extraction from soybean flour or Soybean Protein Isolate in pressurized water system. The optimal conditions conducted gave an extraction yield of 85% from soybean flour. For Soybean Protein Isolate compared to soybean flour, the isoflavone extraction yield is 61%.

Parameters affecting enzyme-assisted aqueous extraction of extruded sunflower meal.

Microscopic observation of sunflower meal before and after extraction indicated that extensive cellular disruption was achieved by extrusion, but that unextracted oil remained sequestered as coalesced oil within the void spaces of disrupted cotyledon cells. A full factorial design experiment was defined to develop aqueous extraction processing (AEP) with and without enzymes to improve vegetable oil extraction yields of extruded sunflower meal. This experimental design studied the influence of four parameters, agitation, liquid/solid (L/S) ratio, and cellulase and protease addition, on extraction yield of lipid and protein.

Comparison of different twin-screw extraction conditions for the production of arabinoxylans.

The aim of this article is to compare two different sets of optimal conditions for twin-screw extraction of xylans and define their influence on the purification steps, combining ultrafiltration and industrial chromatography. Two xylan extracts were obtained by twin-screw extrusion of straw and bran. Condition 1 used a high straw/bran ratio (equal to 6) and high sodium hydroxide content, and condition 2 used a lower straw/bran ratio (equal to 2) and low sodium hydroxide content.

Twin-screw extrusion for hemicellulose recovery: influence on extract purity and purification performance.

A twin-screw extruder was used for the extraction of wheat bran hemicelluloses by the co-extrusion of wheat straw and bran. As compared with a stirred reactor extraction, a twin-screw extruder resulted in a lower extraction rate (only about 24% of hemicelluloses in the wheat bran), but it has the advantages of a shorter residence time for the vegetable matter and a lower chemical and water consumption. Hemicellulose powder production is usually effected via an expensive alcoholic precipitation step after concentration.