Intrinsic efficiency limits in low-bandgap non-fullerene acceptor organic solar cells.

In bulk heterojunction (BHJ) organic solar cells (OSCs) both the electron affinity (EA) and ionization energy (IE) offsets at the donor-acceptor interface should equally control exciton dissociation. Here, we demonstrate that in low-bandgap non-fullerene acceptor (NFA) BHJs ultrafast donor-to-acceptor energy transfer precedes hole transfer from the acceptor to the donor and thus renders the EA offset virtually unimportant. Moreover, sizeable bulk IE offsets of about 0.

Predictive modelling of structure formation in semiconductor films produced by meniscus-guided coating.

Meniscus-guided coating methods, such as zone casting, dip coating and solution shearing, are scalable laboratory models for large-area solution coating of functional materials for thin-film electronics. Unfortunately, the general lack of understanding of how the coating parameters affect the dry-film morphology upholds trial-and-error experimentation and delays lab-to-fab translation. We present herein a model that predicts dry-film morphologies produced by meniscus-guided coating of a crystallizing solute.

Key Parameters Requirements for Non-Fullerene-Based Organic Solar Cells with Power Conversion Efficiency >20.

The reported power conversion efficiencies (PCEs) of nonfullerene acceptor (NFA) based organic photovoltaics (OPVs) now exceed 14% and 17% for single-junction and two-terminal tandem cells, respectively. However, increasing the PCE further requires an improved understanding of the factors limiting the device efficiency. Here, the efficiency limits of single-junction and two-terminal tandem NFA-based OPV cells are examined with the aid of a numerical device simulator that takes into account the optical properties of the active material(s), charge recombination effects, and the hole and electron mobilities in the active layer of the device.

Isoindigo-3,4-Difluorothiophene Polymer Acceptors Yield "All-Polymer" Bulk-Heterojunction Solar Cells with over 7 % Efficiency.

Poly(isoindigo-alt-3,4-difluorothiophene) (PIID[2F]T) analogues used as "polymer acceptors" in bulk-heterojunction (BHJ) solar cells achieve >7 % efficiency when used in conjunction with the polymer donor PBFTAZ (model system; copolymer of benzo[1,2-b:4,5-b']dithiophene and 5,6-difluorobenzotriazole). Considering that most efficient polymer-acceptor alternatives to fullerenes (e.g.

Hybrid tandem quantum dot/organic photovoltaic cells with complementary near infrared absorption.

Monolithically integrated hybrid tandem solar cells that effectively combine solution-processed colloidal quantum dot (CQD) and organic bulk heterojunction subcells to achieve tandem performance that surpasses the individual subcell efficiencies have not been demonstrated to date. In this work, we demonstrate hybrid tandem cells with a low bandgap PbS CQD subcell harvesting the visible and near-infrared photons and a polymer:fullerene-poly (diketopyrrolopyrrole-terthiophene) (PDPP3T):[6,6]-phenyl-C-butyric acid methyl ester (PCBM)-top cell absorbing effectively the red and near-infrared photons of the solar spectrum in a complementary fashion. The two subcells are connected in series via an interconnecting layer (ICL) composed of a metal oxide layer, a conjugated polyelectrolyte, and an ultrathin layer of Au.

Thieno[3,4-c]pyrrole-4,6-dione-3,4-difluorothiophene Polymer Acceptors for Efficient All-Polymer Bulk Heterojunction Solar Cells.

Branched-alkyl-substituted poly(thieno[3,4-c]pyrrole-4,6-dione-alt-3,4-difluorothiophene) (PTPD[2F]T) can be used as a polymer acceptor in bulk heterojunction (BHJ) solar cells with a low-band-gap polymer donor (PCE10) commonly used with fullerenes. The "all-polymer" BHJ devices made with PTPD[2F]T achieve efficiencies of up to 4.4 %.

Impact of Fluorine Substituents on π-Conjugated Polymer Main-Chain Conformations, Packing, and Electronic Couplings.

Taking the π-conjugated polymers PBDT[2X]T (X = H, F) as model systems, the effects of fluorine substitution on main-chain conformations, packing, and electronic couplings are examined. This combination of molecular dynamics simulations and solid-state NMR shows that a higher propensity for backbone planarity in PBDT[2F]T leads to more pronounced, yet staggered, chain stacking, which generally leads to higher electronic couplings and binding energy between neighboring chains.

Electropolymerized Star-Shaped Benzotrithiophenes Yield π-Conjugated Hierarchical Networks with High Areal Capacitance.

Unlabelled: High-surface-area π-conjugated polymeric networks have the potential to lend outstanding capacitance to supercapacitors because of the pronounced faradaic processes that take place across the dense intimate interface between active material and electrolytes. In this report, we describe how benzo[1,2-b:3,4-b':5,6-b″]trithiophene (BTT) and tris(ethylenedioxythiophene)benzo[1,2-b:3,4-b':5,6-b″]trithiophene (TEBTT) can serve as 2D (trivalent) building blocks in the development of electropolymerized hierarchical π-conjugated frameworks with particularly high areal capacitance. In comparing electropolymerized networks of BTT, TEBTT, and their copolymers with EDOT, we show that TEBTT/EDOT-based copolymers, i.

Homo-Tandem Polymer Solar Cells with VOC >1.8 V for Efficient PV-Driven Water Splitting.

Efficient homo-tandem and triple-junction polymer solar cells are constructed by stacking identical subcells composed of the wide-bandgap polymer PBDTTPD, achieving power conversion efficiencies >8% paralleled by open-circuit voltages >1.8 V. The high-voltage homo-tandem is used to demonstrate PV-driven electrochemical water splitting with an estimated solar-to-hydrogen conversion efficiency of ≈6%.

Dependence of crystallite formation and preferential backbone orientations on the side chain pattern in PBDTTPD polymers.

Alkyl substituents appended to the π-conjugated main chain account for the solution-processability and film-forming properties of most π-conjugated polymers for organic electronic device applications, including field-effect transistors (FETs) and bulk-heterojunction (BHJ) solar cells. Beyond film-forming properties, recent work has emphasized the determining role that side-chain substituents play on polymer self-assembly and thin-film nanostructural order, and, in turn, on device performance. However, the factors that determine polymer crystallite orientation in thin-films, implying preferential backbone orientation relative to the device substrate, are a matter of some debate, and these structural changes remain difficult to anticipate.

Importance of the donor:fullerene intermolecular arrangement for high-efficiency organic photovoltaics.

The performance of organic photovoltaic (OPV) material systems are hypothesized to depend strongly on the intermolecular arrangements at the donor:fullerene interfaces. A review of some of the most efficient polymers utilized in polymer:fullerene PV devices, combined with an analysis of reported polymer donor materials wherein the same conjugated backbone was used with varying alkyl substituents, supports this hypothesis. Specifically, the literature shows that higher-performing donor-acceptor type polymers generally have acceptor moieties that are sterically accessible for interactions with the fullerene derivative, whereas the corresponding donor moieties tend to have branched alkyl substituents that sterically hinder interactions with the fullerene.

Highly transparent and UV-resistant superhydrophobic SiO(2)-coated ZnO nanorod arrays.

Highly transparent and UV-resistant superhydrophobic arrays of SiO2-coated ZnO nanorods are prepared in a sequence of low-temperature (<150 °C) steps on both glass and thin sheets of PET (2 × 2 in.(2)), and the superhydrophobic nanocomposite is shown to have minimal impact on solar cell device performance under AM1.5G illumination.

Enhanced solid-state order and field-effect hole mobility through control of nanoscale polymer aggregation.

Efficient charge carrier transport in organic field-effect transistors (OFETs) often requires thin films that display long-range order and close π-π packing that is oriented in-plane with the substrate. Although some polymers have achieved high field-effect mobility with such solid-state properties, there are currently few general strategies for controlling the orientation of π-stacking within polymer films. In order to probe structural effects on polymer-packing alignment, furan-containing diketopyrrolopyrrole (DPP) polymers with similar optoelectronic properties were synthesized with either linear hexadecyl or branched 2-butyloctyl side chains.

A mechanistic understanding of processing additive-induced efficiency enhancement in bulk heterojunction organic solar cells.

The addition of processing additives is a widely used approach to increase power conversion efficiencies for many organic solar cells. We present how additives change the polymer conformation in the casting solution leading to a more intermixed phase-segregated network structure of the active layer which in turn results in a 5-fold enhancement in efficiency.

Semi-transparent polymer solar cells with excellent sub-bandgap transmission for third generation photovoltaics.

Semi-transparent organic photovoltaics are of interest for a variety of photovoltaic applications, including solar windows and hybrid tandem photovoltaics. The figure shows a photograph of our semi-transparent solar cell, which has a power conversion efficiency of 5.0%, with an above bandgap transmission of 34% and a sub-bandgap transmission of 81%.

Gram-scale fractionation of nanodiamonds by density gradient ultracentrifugation.

Size is a defining characteristic of nanoparticles; it influences their optical and electronic properties as well as their interactions with molecules and macromolecules. Producing nanoparticles with narrow size distributions remains one of the main challenges to their utilization. At this time, the number of practical approaches to optimize the size distribution of nanoparticles in many interesting materials systems, including diamond nanocrystals, remains limited.

Linear side chains in benzo[1,2-b:4,5-b']dithiophene-thieno[3,4-c]pyrrole-4,6-dione polymers direct self-assembly and solar cell performance.

While varying the size and branching of solubilizing side chains in π-conjugated polymers impacts their self-assembling properties in thin-film devices, these structural changes remain difficult to anticipate. This report emphasizes the determining role that linear side-chain substituents play in poly(benzo[1,2-b:4,5-b']dithiophene-thieno[3,4-c]pyrrole-4,6-dione) (PBDTTPD) polymers for bulk heterojunction (BHJ) solar cell applications. We show that replacing branched side chains by linear ones in the BDT motifs induces a critical change in polymer self-assembly and backbone orientation in thin films that correlates with a dramatic drop in solar cell efficiency.

Synthetic principles directing charge transport in low-band-gap dithienosilole-benzothiadiazole copolymers.

Given the fundamental differences in carrier generation and device operation in organic thin-film transistors (OTFTs) and organic photovoltaic (OPV) devices, the material design principles to apply may be expected to differ. In this respect, designing organic semiconductors that perform effectively in multiple device configurations remains a challenge. Following "donor-acceptor" principles, we designed and synthesized an analogous series of solution-processable π-conjugated polymers that combine the electron-rich dithienosilole (DTS) moiety, unsubstituted thiophene spacers, and the electron-deficient core 2,1,3-benzothiadiazole (BTD).

Side-chain tunability of furan-containing low-band-gap polymers provides control of structural order in efficient solar cells.

The solution-processability of conjugated polymers in organic solvents has classically been achieved by modulating the size and branching of alkyl substituents appended to the backbone. However, these substituents impact structural order and charge transport properties in thin-film devices. As a result, a trade-off must be found between material solubility and insulating alkyl content.

Efficient small molecule bulk heterojunction solar cells with high fill factors via pyrene-directed molecular self-assembly.

Efficient organic photovoltaic (OPV) materials are constructed by attaching completely planar, symmetric end-groups to donor-acceptor electroactive small molecules. Appending C2-pyrene as the small molecule end-group to a diketopyrrolopyrrole core leads to materials with a tight, aligned crystal packing and favorable morphology dictated by π-π interactions, resulting in high power conversion efficiencies and high fill factors. The use of end-groups to direct molecular self-assembly is an effective strategy for designing high-performance small molecule OPV devices.