Evolution of Defects, Morphology, and Strain during FAMAPbI Perovskite Vacuum Deposition: Insights from In Situ Photoluminescence and X-ray Scattering.

At present, the power conversion efficiency of single-junction perovskite-based solar cells reaches over 26%. The further efficiency increase of perovskite-based optoelectronic devices is limited mainly by defects, causing the nonradiative recombination of charge carriers. To improve efficiency and ensure reproducible fabrication of high-quality layers, it is crucial to understand the perovskite nucleation and growth mechanism along with associated process control to reduce the defect density.

SERS Performance of TiCT MXene-Based Substrates Correlates with Surface Morphology.

The surface-enhanced Raman scattering (SERS) properties of low-dimensional semiconducting MXene nanoflakes have been investigated over the last decade. Despite this fact, the relationship between the surface characteristics and SERSing performance of a MXene layer has yet to be comprehensively investigated and elucidated. This work shows the importance of surface morphology on the overall SERS effect by studying few-layer TiCT MXene-based SERS substrates fabricated by vacuum-assisted filtration (VAF) and spray coating on filter paper.

Operando Spatial and Temporal Tracking of Axial Stresses and Interfaces in Solid-state Batteries.

Solid-state batteries have the potential to replace the current generation of liquid electrolyte batteries. However, the major limitation resulting from their solid-state architecture is the gradual loss of ionic conductivity due to the loss of physical contact between the individual battery components during charging/discharging. This is mainly due to mechanical stresses caused by volume changes in the cathode and anode during lithiation and delithiation.

Structure and Thermal Stability of ε/κ-GaO Films Deposited by Liquid-Injection MOCVD.

We report on crystal structure and thermal stability of epitaxial ε/κ-Ga2O3 thin films grown by liquid-injection metal−organic chemical vapor deposition (LI-MOCVD). Si-doped Ga2O3 films with a thickness of 120 nm and root mean square surface roughness of ~1 nm were grown using gallium-tetramethylheptanedionate (Ga(thd)3) and tetraethyl orthosilicate (TEOS) as Ga and Si precursor, respectively, on c-plane sapphire substrates at 600 °C. In particular, the possibility to discriminate between ε and κ-phase Ga2O3 using X-ray diffraction (XRD) φ-scan analysis or electron diffraction analysis using conventional TEM was investigated.

Evolution of Structure and Optoelectronic Properties During Halide Perovskite Vapor Deposition.

The efficiency of perovskite-based solar cells has increased dramatically over the past decade to as high as 25%, making them very attractive for commercial use. Vapor deposition is a promising technique that potentially enables fabrication of perovskite solar cells on large areas. However, to implement a large-scale deposition method, understanding and controlling the specific growth mechanisms are essential for the reproducible fabrication of high-quality layers.

Effect of Dexamethasone on Thermoresponsive Behavior of Poly(2-Oxazoline) Diblock Copolymers.

Thermoresponsive polymers play an important role in designing drug delivery systems for biomedical applications. In this contribution, the effect of encapsulated hydrophobic drug dexamethasone on thermoresponsive behavior of diblock copolymers was studied. A small series of diblock copoly(2-oxazoline)s was prepared by combining thermoresponsive 2--propyl-2-oxazoline (PrOx) and hydrophilic 2-methyl-2-oxazoline (MeOx) in two ratios and two polymer chain lengths.

3D Networks of Ge Quantum Wires in Amorphous Alumina Matrix.

Recently demonstrated 3D networks of Ge quantum wires in an alumina matrix, produced by a simple magnetron sputtering deposition enables the realization of nanodevices with tailored conductivity and opto-electrical properties. Their growth and ordering mechanisms as well as possibilities in the design of their structure have not been explored yet. Here, we investigate a broad range of deposition conditions leading to the formation of such quantum wire networks.

Langmuir-Scheaffer Technique as a Method for Controlled Alignment of 1D Materials.

A widely applicable method for aligning 1D materials, and in particular carbon nanotubes (CNTs), independent of their preparation would be very useful as the growth methods for these materials are substance-specific. Langmuir-Schaefer (LS) deposition could be such an approach for alignment, as it aligns a large number of 1D materials independently of the desired substrate. However, the mechanism and required conditions for alignment of 1D nanomaterials in a Langmuir trough are still unclear.

Tailoring the interparticle distance in Langmuir nanoparticle films.

The ability to control the interparticle distance in self-assembled arrays of nanoparticles plays an important role in a large number of applications, which require tunable electronic and photonic properties. Importantly, practical applications in real devices rely on arrays satisfying more stringent requirements of lateral homogeneity controlled over a large scale. Herein, the interparticle distance in ordered nanoparticle assemblies was controlled by varying the nanoparticle effective size via the molecular chemical nature and chain length of the ligand.

Kinetics of Polymer-Fullerene Phase Separation during Solvent Annealing Studied by Table-Top X-ray Scattering.

Solvent annealing is an efficient way of phase separation in polymer-fullerene blends to optimize bulk heterojunction morphology of active layer in polymer solar cells. To track the process in real time across all relevant stages of solvent evaporation, laboratory-based in situ small- and wide-angle X-ray scattering measurements were applied simultaneously to a model P3HT:PCBM blend dissolved in dichlorobenzene. The PCBM molecule agglomeration starts at ∼7 wt % concentration of solid content of the blend in solvent.