A Comparative Study of Mechanism and Performance of Anionic and Cationic Dialdehyde Nanocelluloses for Dye Adsorption and Separation.

In this study, anionic dialdehyde cellulose (DAC) and cationic dialdehyde cellulose (c-DAC) nanofibrous adsorbents were prepared via a two-step reaction from bamboo pulp, using sodium periodate and Girard's reagent T as oxidizing and cationizing agents, respectively. The performance of DAC and c-DAC for selective dye adsorption and separation was evaluated by six different organic dyes (with varying charge properties) and certain binary mixtures. Both adsorbents could remove the dyes but with different capability, where DAC exhibited high adsorption efficiency against cationic dyes (e.

Synthesis and Characterization of a High Flux Nanocellulose-Cellulose Acetate Nanocomposite Membrane.

Despite the advantages of membrane processes, their high energy requirement remains a major challenge. Fabrication of nanocomposite membranes by incorporating various nanomaterials in the polymer matrix has shown promise for enhancing membrane flux. In this study, we embed functionalized cellulose nanofibers (CNFs) with high aspect ratios in the polymer matrix to create hydrophilic nanochannels that reduce membrane resistance and facilitate the facile transport of water molecules through the membrane.

Multilayer Dye Adsorption in Activated Carbons-Facile Approach to Exploit Vacant Sites and Interlayer Charge Interaction.

Altering the textural properties of activated carbons (ACs) via physicochemical techniques to increase their specific surface area and/or to manipulate their pore size is a common practice to enhance their adsorption capacity. Instead, this study proposes the utilization of the vacant sites remaining unoccupied after dye uptake saturation by removing the steric hindrance and same-charge repulsion phenomena via multilayer adsorption. Herein, it has been shown that the adsorption capacity of the fresh AC is a direct function of the dye molecular size.

A mechanistic study of in situ chemical cleaning-in-place for a PTFE flat sheet membrane: fouling mitigation and membrane characterization.

This study aimed at unfolding the role and mechanisms of chemically enhanced cleaning-in-place (CIP) regimes in fouling control of polytetrafluoroethylene (PTFE) made flat sheet (FS) membrane bio-reactors (MBRs). The trans-membrane pressure (TMP) was successfully maintained below 10 kPa using a daily CIP regime consisting of 100 to 600 mg l(-1) of NaOCl and cake layer resistance control was shown to be critical for effective high-flux MBR operation. In contrast, in the control unit without the CIP, the TMP exceeded 35 kPa at a flux of 40 LMH.

Sustainable development of tyre char-based activated carbons with different textural properties for value-added applications.

This paper aims at the sustainable development of activated carbons for value-added applications from the waste tyre pyrolysis product, tyre char, in order to make pyrolysis economically favorable. Two activation process parameters, activation temperature (900, 925, 950 and 975 °C) and residence time (2, 4 and 6 h) with steam as the activating agent have been investigated. The textural properties of the produced tyre char activated carbons have been characterized by nitrogen adsorption-desorption experiments at -196 °C.

Aluminosilicate-based adsorbent in equimolar and non-equimolar binary-component heavy metal removal systems.

Cadmium (Cd) and lead (Pb) are toxic heavy metals commonly used in various industries. The simultaneous presence of these metals in wastewater amplifies the toxicity of wastewater and the complexity of the treatment process. This study has investigated the selective behavior of an aluminosilicate-based mesoporous adsorbent.

Aqueous mercury adsorption by activated carbons.

Due to serious public health threats resulting from mercury pollution and its rapid distribution in our food chain through the contamination of water bodies, stringent regulations have been enacted on mercury-laden wastewater discharge. Activated carbons have been widely used in the removal of mercuric ions from aqueous effluents. The surface and textural characteristics of activated carbons are the two decisive factors in their efficiency in mercury removal from wastewater.

Toward environmentally-benign utilization of nonmetallic fraction of waste printed circuit boards as modifier and precursor.

Electronic waste, including printed circuit boards, is growing at an alarming rate due to the accelerated technological progress and the shorter lifespan of the electronic equipment. In the past decades, due to the lack of proper economic and environmentally-benign recycling technologies, a major fraction of e-waste generated was either destined to landfills or incinerated with the sole intention of its disposal disregarding the toxic nature of this waste. Recently, with the increasing public awareness over their environment and health issues and with the enaction of more stringent regulations, environmentally-benign recycling has been driven to be an alternative option partially replacing the traditional eco-unfriendly disposal methods.

Waste printed circuit board recycling techniques and product utilization.

E-waste, in particular waste PCBs, represents a rapidly growing disposal problem worldwide. The vast diversity of highly toxic materials for landfill disposal and the potential of heavy metal vapors and brominated dioxin emissions in the case of incineration render these two waste management technologies inappropriate. Also, the shipment of these toxic wastes to certain areas of the world for eco-unfriendly "recycling" has recently generated a major public outcry.

Removal of cadmium ions from wastewater using innovative electronic waste-derived material.

Cadmium is a highly toxic heavy metal even at a trace level. In this study, a novel material derived from waste PCBs has been applied as an adsorbent to remove cadmium ions from aqueous solutions. The effects of various factors including contact time, initial cadmium ion concentration, pH and adsorbent dosage have been evaluated.

Toxic heavy metal capture using a novel electronic waste-based material-mechanism, modeling and comparison.

In the modern communication era, the disposal of printed circuit boards is ecologically of dire concern on a global scale. The two prevalent methods applied for the disposal of this waste are either incineration or landfilling both of which are viewed with skepticism due to their negative environmental impact. Activation of the nonmetallic fraction of this waste leads to the development of a mesoporous material with highly functional groups which can potentially be applied for heavy metal uptake.

Novel application of the nonmetallic fraction of the recycled printed circuit boards as a toxic heavy metal adsorbent.

Printed circuit boards (PCBs) constitute one of the major sources of toxicity in landfill areas throughout the world. Hence, PCB recycling and separation of its metallic and nonmetallic components has been considered a major ecological breakthrough. Many studies focus on the metallic fraction of the PCBs due to its economic benefits whereas the nonmetallic powder (NMP) has been left isolated.