Characterization of thermo-oxidative behavior of ethylcellulose oleogels.

The thermo-oxidative behavior crucial to the applicability of ethylcellulose (EC) oleogels is characterized. Not only did we take into account the composition of the gel network in relation to textural attributes, but also the dynamic chemical changes occurred during formation, heating, and holding of the gels. EC oleogel oxidative stability showed that at 6.

Development of Novel Shortenings Structured by Ethylcellulose Oleogels.

A novel shortening was developed based on oleogels structured by ethylcellulose (EC) polymers. The texture and oil retention ability of EC oleogels were characterized against the level of viscosity of different grades of EC, as well as the rheological properties in relation to the polymer structure in the gel network. EC100, which has an average viscosity of 100 cP, was selected as the most suitable organogelator at 4% (w/w) in combination with base oil (30% degree of saturation by mixing palm stearin and soybean oil) to form the shortening.

Hierarchically designed three-dimensional macro/mesoporous carbon frameworks for advanced electrochemical capacitance storage.

Mesoporous carbon (m-C) has potential applications as porous electrodes for electrochemical energy storage, but its applications have been severely limited by the inherent fragility and low electrical conductivity. A rational strategy is presented to construct m-C into hierarchical porous structures with high flexibility by using a carbon nanotube (CNT) sponge as a three-dimensional template, and grafting Pt nanoparticles at the m-C surface. This method involves several controllable steps including solution deposition of a mesoporous silica (m-SiO2 ) layer onto CNTs, chemical vapor deposition of acetylene, and etching of m-SiO2 , resulting in a CNT@m-C core-shell or a CNT@m-C@Pt core-shell hybrid structure after Pt adsorption.

Core-double-shell, carbon nanotube@polypyrrole@MnO₂ sponge as freestanding, compressible supercapacitor electrode.

Design and fabrication of structurally optimized electrode materials are important for many energy applications such as supercapacitors and batteries. Here, we report a three-component, hierarchical, bulk electrode with tailored microstructure and electrochemical properties. Our supercapacitor electrode consists of a three-dimensional carbon nanotube (CNT) network (also called sponge) as a flexible and conductive skeleton, an intermediate polymer layer (polypyrrole, PPy) with good interface, and a metal oxide layer outside providing more surface area.

A compressible mesoporous SiO2 sponge supported by a carbon nanotube network.

Applications of mesoporous silica (m-SiO2) have suffered from its fragility (monolithic m-SiO2 easily collapses under compression) and limited internal molecular exchange through small channels. Previously reported hierarchical porous m-SiO2 structures containing interconnected macropores could improve adsorption properties, but they were still intrinsically fragile without sufficient mechanical strength to sustain deformation. Here, we embed a three-dimensional carbon nanotube (CNT) skeleton into m-SiO2 to fabricate bulk, robust sponges that can be compressed to large strains (60% volume reduction) repeatedly in both air and water.

Graphene nanoribbon aerogels unzipped from carbon nanotube sponges.

Graphene nanoribbon aerogels are fabricated by directly unzipping multi-walled carbon nanotube sponges. These fascinating materials have potential applications as high performance nanocomposites and supercapacitor electrodes.

Macroscopic, flexible, high-performance graphene ribbons.

Tailoring the structure and properties of graphene fibers is an important step toward practical applications. Here, we report macroscopic, long graphene ribbons formed by combining electrostatic interaction and shear stress during the wet-spinning process. The graphene ribbons are flexible and can be woven into complex structures, and the ribbon morphology can be tailored by controlling the orientation of wrinkles to obtain elasticity within a modest strain.

Boosting supercapacitor performance of carbon fibres using electrochemically reduced graphene oxide additives.

Modifying conventional materials with new recipes represents a straightforward yet efficient way to realize large-scale applications of new materials. Electrochemically reduced graphene oxide (ERGO) coated carbon fibres (CFs), prepared as fibre-like supercapacitor electrodes, exhibited excellent electrochemical energy storage performance. Upon addition of only a small amount (~1 wt%) of ERGO, the hybrid fibres showed superior electrochemical capacitances (nearly three orders of magnitude enhanced) compared to pure CFs in both aqueous and gel electrolytes.

Flexible all solid-state supercapacitors based on chemical vapor deposition derived graphene fibers.

Flexible all-solid-state supercapacitors based on graphene fibers are demonstrated in this study. Surface-deposited oxide nanoparticles are used as pseudo-capacitor electrodes to achieve high capacitance. This supercapacitor electrode has an areal capacitance of 42 mF cm(-2), which is comparable to the capacitance for fiber-based supercapacitors reported to date.

Overtwisted, resolvable carbon nanotube yarn entanglement as strain sensors and rotational actuators.

Introducing twists into carbon nanotube yarns could produce hierarchical architectures and extend their application areas. Here, we utilized such twists to produce elastic strain sensors over large strain (up to 500%) and rotation actuators with high energy density. We show that a helical nanotube yarn can be overtwisted into highly entangled, macroscopically random but locally organized structures, consisting of mostly double-helix segments intertwined together.

Highly deformation-tolerant carbon nanotube sponges as supercapacitor electrodes.

Developing flexible and deformable supercapacitor electrodes based on porous materials is of high interest in energy related fields. Here, we show that carbon nanotube sponges, consisting of highly porous conductive networks, can serve as compressible and deformation-tolerant supercapacitor electrodes in aqueous or organic electrolytes. In aqueous electrolytes, the sponges maintain a similar specific capacitance (>90% of the original value) under a predefined compressive strain of 50% (corresponding to a volume reduction of 50%), and retain more than 70% of the original capacitance under 80% strain while the volume normalized capacitance increases by 3-fold.

Colloidal antireflection coating improves graphene-silicon solar cells.

Carbon nanotube-Si and graphene-Si solar cells have attracted much interest recently owing to their potential in simplifying manufacturing process and lowering cost compared to Si cells. Until now, the power conversion efficiency of graphene-Si cells remains under 10% and well below that of the nanotube-Si counterpart. Here, we involved a colloidal antireflection coating onto a monolayer graphene-Si solar cell and enhanced the cell efficiency to 14.

Elastic carbon nanotube straight yarns embedded with helical loops.

Introducing stretchability and elasticity into carbon nanotube (CNT) yarns could extend their applications to areas such as stretchable and deformable fiber-based devices and strain sensors. Here, we convert a straight and inelastic yarn into a highly elastic structure by spinning a predefined number of helical loops along the yarn, resulting in a short helical segment with smooth structural transition to the straight portions. The loop-forming process is well controlled, and the obtained straight-helical-straight hybrid yarn is freestanding, stable, and based entirely on CNTs.

Highly twisted double-helix carbon nanotube yarns.

The strength and flexibility of carbon nanotubes (CNTs) allow them to be constructed into a variety of innovated architectures with fascinating properties. Here, we show that CNTs can be made into a highly twisted yarn-derived double-helix structure by a conventional twist-spinning process. The double-helix is a stable and hierarchical configuration consisting of two single-helical yarn segments, with controlled pitch and unique mechanical properties.

TiO₂-coated carbon nanotube-silicon solar cells with efficiency of 15%.

Combining carbon nanotubes (CNTs), graphene or conducting polymers with conventional silicon wafers leads to promising solar cell architectures with rapidly improved power conversion efficiency until recently. Here, we report CNT-Si junction solar cells with efficiencies reaching 15% by coating a TiO₂ antireflection layer and doping CNTs with oxidative chemicals, under air mass (AM 1.5) illumination at a calibrated intensity of 100 mW/cm² and an active device area of 15 mm².

Fiber and fabric solar cells by directly weaving carbon nanotube yarns with CdSe nanowire-based electrodes.

Electrode materials are key components for fiber solar cells, and when combined with active layers (for light absorption and charge generation) in appropriate ways, they enable design and fabrication of efficient and innovative device structures. Here, we apply carbon nanotube yarns as counter electrodes in combination with CdSe nanowire-grafted primary electrodes (Ti wire) for making fiber and fabric-shaped photoelectrochemical cells with power conversion efficiencies in the range 1% to 2.9%.

Strong and reversible modulation of carbon nanotube-silicon heterojunction solar cells by an interfacial oxide layer.

Deposition of nanostructures such as carbon nanotubes on Si wafers to make heterojunction structures is a promising route toward high efficiency solar cells with reduced cost. Here, we show a significant enhancement in the cell characteristics and power conversion efficiency by growing a silicon oxide layer at the interface between the nanotube film and Si substrate. The cell efficiency increases steadily from 0.

Super-stretchable spring-like carbon nanotube ropes.

Spring-like carbon nanotube ropes consisting of perfectly arranged loops are fabricated by spinning single-walled nanotube films, and can sustain tensile strains as high as 285%.

Strong, conductive carbon nanotube fibers as efficient hole collectors.

We present the photovoltaic properties of heterojunctions made from single-walled carbon nanotube (SWNT) fibers and n-type silicon wafers. The use of the opaque SWNT fiber allows photo-generated holes to transport along the axis direction of the fiber. The heterojunction solar cells show conversion efficiencies of up to 3.

Wire-supported CdSe nanowire array photoelectrochemical solar cells.

Previous fiber-shaped solar cells are based on polymeric materials or dye-sensitized wide band-gap oxides. Here, we show that efficient fiber solar cells can be made from semiconducting nanostructures (e.g.

Suspended, straightened carbon nanotube arrays by gel chapping.

We report large-scale self-assembly of suspended, straightened, single-walled carbon nanotubes (SWNTs) across regular TiO(2) gel islands. By coating a SWNT network on top of a pool of the TiO(2) colloid and inducing a rapid drying and chapping process, initially curled, random SWNTs can be straightened into aligned arrays and suspended across the island gaps. The suspended SWNT arrays were grafted by semiconducting or metallic nanoparticles, resulting in hybrid structures with tailored and neat morphology, and enhanced photoresponse.

[The relationship between the implantation of ovarian stimulated embryos and the expression of leukemia inhibitory factor mRNA in mice metrium].

Objective: To check the expression of leukemia inhibitory factor (Lif) mRNA, and to study the impact of ovarian stimulation on the ability of embryo implantation in mice.

Methods: Pregnancy models of mice were established. The relationship between the implantation of ovarian stimulated embryos and the expression of Lif mRNA in mice metrium was analyzed.

[Primary study on the method for separating mature sperms from human testicular tissue].

This study was aimed to explore a simple and applicable method of separating mature sperms from human testicular tissue for intracytoplasmic sperm injection and embryo transfer. The suspension of human testicular tissue was cultured in 10% human serum albumin and human tubule fluid with different concentrations (0 u/ml; 50 u/ml; 100 u/ml; 150 u/ml; 200 u/ml) of hyaluronidase for 24 h, and then the Percoll gradient centrifugation was processed to separate the sperms; meanwhile the sperms were counted and graded according to their motility. The difference in quality and quantity among the groups and the difference between the groups and the zero-hour culturing group were detected.