The Influence of Er and Zr on the Microstructure and Durability of the Mechanical Properties of an Al-Mg Alloy Containing 7 wt.% of Mg.

Al-Mg alloys are characterized by permanent solid solution hardening and can additionally be work-hardened. The high mechanical properties of Al-Mg alloys with above-standard Mg content obtained after plastic deformation processes decrease over time. The addition of minor alloying elements like Er or Zr is an alternative method to improve the durability of mechanical properties and increase the strength of Al-Mg alloys due to densely and evenly distributed dispersoids being formed.

Nanocomposites Based on Thermoplastic Acrylic Resin with the Addition of Chemically Modified Multi-Walled Carbon Nanotubes.

The main goal of this work was an improvement in the mechanical and electrical properties of acrylic resin-based nanocomposites filled with chemically modified carbon nanotubes. For this purpose, the surface functionalization of multi-walled carbon nanotubes (MWCNTs) was carried out by means of aryl groups grafting via the diazotization reaction with selected aniline derivatives, and then nanocomposites based on ELIUM resin were fabricated. FT-IR analysis confirmed the effectiveness of the carried-out chemical surface modification of MWCNTs as new bands on FT-IR spectra appeared in the measurements.

Effect of High-Pressure Torsion on Phase Formation and Mechanical Properties of a High-Entropy TiZrHfMoCrCo Alloy.

This investigation delved into the alterations in the mechanical properties of a TiZrHfMoCrCo high-entropy alloy due to phase transformations induced by high-pressure torsion (HPT). The alloy's genesis involved levitation melting within an argon atmosphere, presenting two distinct states for analysis: the initial, post-manufacturing state and the state subsequent to HPT treatment. The original alloy featured a composition comprising a singular A2 phase with a bcc lattice and two Laves phases, C15 and C14.

Influence of Surface Preparation on the Microstructure and Mechanical Properties of Cold-Sprayed Nickel Coatings on Al 7075 Alloy.

This work presents the effect of surface roughness (Al 7075) on the microstructure and mechanical properties of cold-sprayed nickel coatings. Coating analysis included substrate surfaces and coating geometry, microstructure characterization, microhardness, nanohardness, elastic modulus, and adhesion. The results show that the surface preparation had a significant effect on coating adhesion and microstructure.

Exploring CVD Method for Synthesizing Carbon-Carbon Composites as Materials to Contact with Nerve Tissue.

The main purpose of these studies was to obtain carbon-carbon composites with a core built of carbon fibers and a matrix in the form of pyrolytic carbon (PyC), obtained by using the chemical vapor deposition (CVD) method with direct electrical heating of a bundle of carbon fibers as a potential electrode material for nerve tissue stimulation. The methods used for the synthesis of PyC proposed in this paper allow us, with the appropriate selection of parameters, to obtain reproducible composites in the form of rods with diameters of about 300 µm in 120 s (CF_PyC_120). To evaluate the materials, various methods such as scanning electron microscopy (SEM), scanning transmission electron microscope (STEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and tensiometer techniques were used to study their microstructural, structural, chemical composition, surface morphology, and surface wettability.

ZnO-decorated green-synthesized multi-doped carbon dots from for sustainable photocatalytic carbamazepine degradation.

The promising green synthesis of carbon dots (CDs) from microalga was achieved using simple hydrothermal and microwave-assisted methods. Doping of nanomaterials by nonmetals (N, S, and P) was confirmed by X-ray photoelectron spectroscopy (XPS), while the existence of metals in the CDs was confirmed by inductively coupled plasma optical emission spectroscopy (ICP-OES) and transmission electron microscopy (TEM), and Mg, Ca, K, and Na were found as the dominant doped metals. The novel nanomaterials with excellent photoluminescence (PL) properties were used for the modification of ZnO obtained by a simple hydrothermal process.

Effect of coagulation temperature on cooking integrity of heat and acid-induced milk gels.

Heat and acid-induced milk gels do not melt or flow upon heating and thus show great potential as a dairy-based protein source for cooking, e.g. for stews.

Tailoring the Stability of Ti-Doped SrFeTiMoO Electrode Materials for Solid Oxide Fuel Cells.

In this work, the stability of Sr(FeMo)O-type perovskites was tailored by the substitution of Mo with Ti. Redox stable SrFeTiMoO (x = 0.1, 0.

Influence of Heat Treatment of Electrospun Carbon Nanofibers on Biological Response.

The main aim of this study is to investigate the effect of fragmentation of electrospun carbon nanofibers (eCNFs) obtained at different temperatures, i.e., at 750 °C, 1000 °C, 1500 °C, 1750 °C and 2000 °C on the cellular response in vitro.

Fe-Co-B Soft Magnetic Ribbons: Crystallization Process, Microstructure and Coercivity.

In this work, a detailed microstructural investigation of as-melt-spun and heat-treated FeCoB ribbons was performed. The as-melt-spun ribbon was predominantly amorphous at room temperature. Subsequent heating demonstrated an amorphous to crystalline α-(Fe,Co) phase transition at 403 °C.

Microstructure of Coatings on Nickel and Steel Platelets Obtained by Co-Milling with NiAl and CrB Powders.

Metal matrix composite coatings are developed to protect parts made from materials susceptible to wear, like nickel alloys or stainless steel. The industry-established deposition method is presently an atmospheric plasma spraying method since it allows the production of both well-adhering and thick coatings. Alternatively, similar coatings could be produced by co-milling of ceramic and alloyed powders together with metallic plates serving as substrates.

Assessment of airway caliber in quantitative videobronchoscopy.

Background: Quantitative assessment of airway caliber is generally confined to indirect methods. Fiberoptic bronchoscopy provides a direct view of the airways, but measurement of the internal size of bronchi in a standard examination is not possible. Using a special image analysis program, we developed a method allowing quantitative assessment of airway caliber by means of videobronchoscopic (VB) examination.