The physiology of saltwater acclimation in large juvenile Atlantic salmon Salmo salar.

The present study investigated the effects of transferring freshwater (FW) acclimated S. salar (678 g) that had been maintained under a constant photoperiod and thermal regime, into FW (salinity 0) and salt water (SW; salinity 35) on growth and physiological responses over a 28 day period. There were no mortalities observed throughout the study and no significant differences in mass or fork length between FW and SW groups after 28 days.

Evaluation of the giant reed (Arundo donax) in horizontal subsurface flow wetlands for the treatment of dairy processing factory wastewater.

Two emergent macrophytes, Arundo donax and Phragmites australis, were established in experimental horizontal subsurface flow (HSSF), gravel-based constructed wetlands (CWs) and challenged by treated dairy processing factory wastewater with a median electrical conductivity of 8.9 mS cm(-1). The hydraulic loading rate was tested at 3.

Generic safety requirements for developing safe insulin pump software.

Background: The authors previously introduced a highly abstract generic insulin infusion pump (GIIP) model that identified common features and hazards shared by most insulin pumps on the market. The aim of this article is to extend our previous work on the GIIP model by articulating safety requirements that address the identified GIIP hazards. These safety requirements can be validated by manufacturers, and may ultimately serve as a safety reference for insulin pump software.

Evaluation of the giant reed (Arundo donax) in horizontal subsurface flow wetlands for the treatment of recirculating aquaculture system effluent.

Introduction: Two emergent macrophytes, Arundo donax and Phragmites australis, were established in experimental subsurface flow, gravel-based constructed wetlands (CWs) receiving untreated recirculating aquaculture system wastewater.

Materials And Methods: The hydraulic loading rate was 3.75 cm day(-1).

Model-based engineering for medical-device software.

This paper demonstrates the benefits of adopting model-based design techniques for engineering medical device software. By using a patient-controlled analgesic (PCA) infusion pump as a candidate medical device, the authors show how using models to capture design information allows for i) fast and efficient construction of executable device prototypes ii) creation of a standard, reusable baseline software architecture for a particular device family, iii) formal verification of the design against safety requirements, and iv) creation of a safety framework that reduces verification costs for future versions of the device software. 1.

Second insulin pump safety meeting: summary report.

Diabetes Technology Society facilitated a second meeting of insulin pump experts at Mills-Peninsula Health Services, San Mateo, California on November 4, 2009, at the request of the Food and Drug Administration, Center for Devices and Radiological Health, Office of Science and Engineering Laboratories. The first such meeting was held in Bethesda, Maryland, on November 12, 2008. The group of physicians, nurses, diabetes educators, and engineers from across the United States discussed safety issues in insulin pump therapy and recommended adjustments to current insulin pump design and use to enhance overall safety.

A hazard analysis for a generic insulin infusion pump.

Background: Researchers at the Food and Drug Administration (FDA)/Center for Device and Radiological Health/Office of Science and Engineering Laboratories have been exploring the concept of model-based engineering as a means for improving the quality of medical device software. Insulin pumps were chosen as a research subject because their design provides the desired degree of research complexity and these types of devices present an ongoing regulatory challenge.

Methods: Insulin pump hazards and their contributing factors are considered in the context of a highly abstract generic insulin infusion pump (GIIP) model.

Traceability and discrimination among differently farmed fish: a case study on Australian Murray cod.

The development of traceability methods to distinguish between farmed and wild-caught fish and seafood is becoming increasingly important. However, very little is known about how to distinguish fish originating from different farms. The present study addresses this issue by attempting to discriminate among intensively farmed freshwater Murray cod originating from different farms (indoor recirculating, outdoor floating cage, and flow through systems) in different geographical areas, using a combination of morphological, chemical, and isotopic analyses.

Age-related changes in ovarian characteristics, plasma sex steroids and fertility during pubertal development in captive female Murray cod Maccullochella peelii peelii.

Age-related changes in ovarian development characteristics and plasma sex steroids in female Murray cod were examined throughout their second, third and fourth years of life to better understand the physiological and endocrine processes associated with puberty in this species in captivity. Spawning performance of 2+ and 3+ year old females was also assessed to identify ontogenetic differences in egg fertility. Puberty was acquired in 38% of 1+ year old females and 100% of age 2+ females.

Temporal dynamics of oocyte development, plasma sex steroids and somatic energy reserves during seasonal ovarian maturation in captive Murray cod Maccullochella peelii peelii.

The temporal dynamics of oocyte growth, plasma sex steroids and somatic energy stores were examined during a 12 month ovarian maturation cycle in captive Murray cod Maccullochella peelii peelii under simulated natural photothermal conditions. Ovarian function was found to be relatively uninhibited in captivity, with the exception that post-vitellogenic follicles failed to undergo final maturation, resulting in widespread pre-ovulatory atresia. Seasonal patterns of oocyte growth were characterised by cortical alveoli accumulation in March, deposition of lipids in April, and vitellogenesis between May and September.

Dietary lipid source modulates in vivo fatty acid metabolism in the freshwater fish, Murray cod (Maccullochella peelii peelii).

The aim of the present investigation was to quantify the fate of C18 and long chain polyunsaturated dietary fatty acids in the freshwater fish, Murray cod, using the in vivo, whole-body fatty acid balance method. Juvenile Murray cod were fed one of five iso-nitrogenous, iso-energetic, semipurified experimental diets in which the dietary fish oil (FO) was replaced (0, 25, 50, 75, and 100%) with a blended vegetable oil (VO), specifically formulated to match the major fatty acid classes [saturated fatty acids, monounsaturated fatty acids, n-3 polyunsaturated fatty acids (PUFA), and n-6 PUFA] of cod liver oil (FO). However, the PUFA fraction of the VO was dominated by C18 fatty acids, while C20/22 fatty acids were prevalent in the FO PUFA fraction.

Risk management in the design of medical device software systems.

The safety of any medical device system is dependent on the application of a disciplined, well-defined, risk management process throughout the product life cycle. Hardware, software, human, and environmental interactions must be assessed in terms of intended use, risk, and cost/benefit criteria. This article addresses these issues in the context of medical devices that incorporate software.