Polycrystalline Diamond Micro-Hotplates.

Micro-hotplate structures are increasingly being investigated for use in a host of applications ranging from broadband infra-red sources within absorption-based gas sensors to in situ heater stages for ultra-high-resolution imaging. With devices usually fabricated from a conductive electrode placed on top of a freestanding radiator element, coefficient of thermal expansion (CTE) mismatches between layers and electro-migration within the heating element typically lead to failure upon exceeding temperatures of 1600 K. In an attempt to mitigate such issues, a series of hotplates of varying geometry have been fabricated from a single layer of mechanically robust, high thermal conductivity, and low CTE boron-doped polycrystalline diamond.

SAW Resonators and Filters Based on ScAlN on Single Crystal and Polycrystalline Diamond.

The massive data transfer rates of nowadays mobile communication technologies demand devices not only with outstanding electric performances but with example stability in a wide range of conditions. Surface acoustic wave (SAW) devices provide a high Q-factor and properties inherent to the employed materials: thermal and chemical stability or low propagation losses. SAW resonators and filters based on Sc0.

Electropositive Nanodiamond-Coated Quartz Microfiber Membranes for Virus and Dye Filtration.

Electropositive membranes demonstrating high flux at low pressure differentials show great promise as universal separation platforms for viruses and other charged entities when centralized systems of water and power are scarce. However, the fabrication of a suitably stable membrane with optimal electrostatic characteristics remains a challenge. Here, hydrogenated detonation nanodiamond was loaded onto a quartz microfiber support membrane and coupled to the membrane surface under a high vacuum annealing process.

High-throughput nitrogen-vacancy center imaging for nanodiamond photophysical characterization and pH nanosensing.

The fluorescent nitrogen-vacancy (NV) defect in diamond has remarkable photophysical properties, including high photostability which allows stable fluorescence emission for hours; as a result, there has been much interest in using nanodiamonds (NDs) for applications in quantum optics and biological imaging. Such applications have been limited by the heterogeneity of NDs and our limited understanding of NV photophysics in NDs, which is partially due to the lack of sensitive and high-throughput methods for photophysical analysis of NDs. Here, we report a systematic analysis of NDs using two-color wide-field epifluorescence imaging coupled to high-throughput single-particle detection of single NVs in NDs with sizes down to 5-10 nm.

Facile Amine Termination of Nanodiamond Particles and Their Surface Reaction Dynamics.

Nanodiamond synthesized by the detonation method is a composite of sp/sp carbon structures; amorphous and disordered-sp carbons populate the surface of a sp diamond core lattice. Because of the production process, various elemental impurities such as N, O, H, and so forth are inherent in interstitial sites or the surface carbon (sp/amorphous) network. Herein, the reaction dynamics on the surface of ultradisperse diamond (UDD) due to the surface transformation or reconstruction during annealing in vacuum with temperatures ranging from ambient to 800 °C is described.

Thick, Adherent Diamond Films on AlN with Low Thermal Barrier Resistance.

The growth of >100-μm-thick diamond layers adherent on aluminum nitride with low thermal boundary resistance between diamond and AlN is presented in this work. The thermal barrier resistance was found to be in the range of 16 m·K/GW, which is a large improvement on the current state-of-the-art. While thick films failed to adhere on untreated AlN films, AlN films treated with hydrogen/nitrogen plasma retained the thick diamond layers.

Production of Metal-Free Diamond Nanoparticles.

In this paper, the controlled production of high-quality metal-free diamond nanoparticles is demonstrated. Milling with tempered steel is shown to leave behind iron oxide contamination which is difficult to remove. Milling with SiN alleviates this issue but generates more nondiamond carbon.

Author Correction: Superconducting Diamond on Silicon Nitride for Device Applications.

A correction to this article has been published and is linked from the HTML and PDF versions of this paper. The error has not been fixed in the paper.

Superconducting boron doped nanocrystalline diamond on boron nitride ceramics.

In this work we have demonstrated the growth of nanocrystalline diamond on boron nitride ceramic. We measured the zeta potential of the ceramics to select the diamond seeds. Diamond was then grown on the seeded ceramics using a microwave chemical vapour deposition system.

Superconducting Diamond on Silicon Nitride for Device Applications.

Chemical vapour deposition (CVD) grown nanocrystalline diamond is an attractive material for the fabrication of devices. For some device architectures, optimisation of its growth on silicon nitride is essential. Here, the effects of three pre-growth surface treatments, often employed as cleaning methods, were investigated.

Air-clad suspended nanocrystalline diamond ridge waveguides.

A hybrid group IV ridge waveguide platform is demonstrated, with potential application across the optical spectrum from ultraviolet to the far infrared wavelengths. The waveguides are fabricated by partial etching of sub-micron ridges in a nanocrystalline diamond thin film grown on top of a silicon wafer. To create vertical confinement, the diamond film is locally undercut by exposing the chip to an isotropic fluorine plasma etch via etch holes surrounding the waveguides, resulting in a mechanically stable suspended air-clad waveguide platform.

Microwave Permittivity of Trace sp Carbon Impurities in Sub-Micron Diamond Powders.

Microwave dielectric loss tangent measurements are demonstrated as a method for quantifying trace sp-hybridized carbon impurities in sub-micron diamond powders. Appropriate test samples are prepared by vacuum annealing at temperatures from 600 to 1200 °C to vary the sp/sp carbon ratio through partial surface graphitization. Microwave permittivity measurements are compared with those obtained using X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and electron energy loss spectroscopy (EELS).

Surface Zeta Potential and Diamond Seeding on Gallium Nitride Films.

The measurement of ζ potential of Ga-face and N-face gallium nitride has been carried out as a function of pH. Both of the faces show negative ζ potential in the pH range 5.5-9.

Effect of slurry composition on the chemical mechanical polishing of thin diamond films.

Nanocrystalline diamond (NCD) thin films grown by chemical vapour deposition have an intrinsic surface roughness, which hinders the development and performance of the films' various applications. Traditional methods of diamond polishing are not effective on NCD thin films. Films either shatter due to the combination of wafer bow and high mechanical pressures or produce uneven surfaces, which has led to the adaptation of the chemical mechanical polishing (CMP) technique for NCD films.

Spectroscopic Ellipsometry of Nanocrystalline Diamond Film Growth.

With the retention of many of the unrivaled properties of bulk diamond but in thin-film form, nanocrystalline diamond (NCD) has applications ranging from micro-/nano-electromechanical systems to tribological coatings. However, with Young's modulus, transparency, and thermal conductivity of films all dependent on the grain size and nondiamond content, compositional and structural analysis of the initial stages of diamond growth is required to optimize growth. Spectroscopic ellipsometry (SE) has therefore been applied to the characterization of 25-75 nm thick NCD samples atop nanodiamond-seeded silicon with a clear distinction between the nucleation and bulk growth regimes discernable.

Positive zeta potential of nanodiamonds.

In this paper, the origin of positive zeta potential exhibited by nanodiamond particles is explained. Positive zeta potentials in nano-structured carbons can be explained by the presence of graphitic planes at the surface, which leave oxygen-free Lewis sites and so promotes the suppression of acidic functional groups. Electron Microscopy and Raman Spectroscopy have been used to show that positive zeta potential of nanodiamond is only exhibited in the presence of sp carbon at the surface.

Chemical Nucleation of Diamond Films.

With the large differences in surface energy between film and substrate in combination with the low sticking coefficient of hydrocarbon radicals, nanocrystalline diamond growth on foreign substrates typically results in poor nucleation densities. A seeding technique is therefore required to realize pinhole-free and thin coalesced films. In this work, a chemical nucleation method for growth of diamond on nondiamond substrates based on 2,2-divinyladamantane is shown.

Silica based polishing of {100} and {111} single crystal diamond.

Diamond is one of the hardest and most difficult to polish materials. In this paper, the polishing of {111} and {100} single crystal diamond surfaces by standard chemical mechanical polishing, as used in the silicon industry, is demonstrated. A Logitech Tribo Chemical Mechanical Polishing system with Logitech SF1 Syton and a polyurethane/polyester polishing pad was used.

Observation of nonlinear dissipation in piezoresistive diamond nanomechanical resonators by heterodyne down-mixing.

We report the observation of nonlinear dissipation in diamond nanomechanical resonators measured by an ultrasensitive heterodyne down-mixing piezoresistive detection technique. The combination of a hybrid structure as well as symmetry breaking clamps enables sensitive piezoresistive detection of multiple orthogonal modes in a diamond resonator over a wide frequency and temperature range. Using this detection method, we observe the transition from purely linear dissipation at room temperature to strongly nonlinear dissipation at cryogenic temperatures.

The diamond superconducting quantum interference device.

Diamond is an electrical insulator in its natural form. However, when doped with boron above a critical level (∼0.25 atom %) it can be rendered superconducting at low temperatures with high critical fields.

Diamond-modified AFM probes: from diamond nanowires to atomic force microscopy-integrated boron-doped diamond electrodes.

In atomic force microscopy (AFM), sharp and wear-resistant tips are a critical issue. Regarding scanning electrochemical microscopy (SECM), electrodes are required to be mechanically and chemically stable. Diamond is the perfect candidate for both AFM probes as well as for electrode materials if doped, due to diamond's unrivaled mechanical, chemical, and electrochemical properties.

Nanocrystalline diamond nanoelectrode arrays and ensembles.

In this report, the fabrication of all-nanocrystalline diamond (NCD) nanoelectrode arrays (NEAs) by e-beam lithography as well as of all-diamond nanoelectrode ensembles (NEEs) using nanosphere lithography is presented. In this way, nanostructuring techniques are combined with the excellent properties of diamond that are desirable for electrochemical sensor devices. Arrays and ensembles of recessed disk electrodes with radii ranging from 150 to 250 nm and a spacing of 10 μm have been fabricated.

Size-dependent reactivity of diamond nanoparticles.

Photonic active diamond nanoparticles attract increasing attention from a wide community for applications in drug delivery and monitoring experiments as they do not bleach or blink over extended periods of time. To be utilized, the size of these diamond nanoparticles needs to be around 4 nm. Cluster formation is therefore the major problem.

Microstructured poly(2-oxazoline) bottle-brush brushes on nanocrystalline diamond.

We report on the preparation of microstructured poly(2-oxazoline) bottle-brush brushes (BBBs) on nanocrystalline diamond (NCD). Structuring of NCD was performed by photolithography and plasma treatment to result in a patterned NCD surface with oxidized and hydrogenated areas. Self-initiated photografting and photopolymerization (SIPGP) of 2-isopropenyl-2-oxazoline (IPOx) resulted in selective grafting of poly(2-isopropenyl-2-oxazoline) (PIPOx) polymer brushes only at the oxidized NCD areas.