Impact of In-Process Crystallinity of Biodegradable Scaffolds Fabricated by Material Extrusion on the Micro- and Nanosurface Topography, Viability, Proliferation, and Differentiation of Human Mesenchymal Stromal Cells.

Due to affordability, and the ability to parametrically control the vital processing parameters, material extrusion is a widely accepted technology in tissue engineering. Material extrusion offers sufficient control over pore size, geometry, and spatial distribution, and can also yield different levels of in-process crystallinity in the resulting matrix. In this study, an empirical model based on four process parameters-extruder temperature, extrusion speed, layer thickness, and build plate temperature-was used to control the level of in-process crystallinity of polylactic acid (PLA) scaffolds.

Finite Element Simplifications and Simulation Reliability in Single Point Incremental Forming.

Single point incremental forming (SPIF) is one of the most promising technologies for the manufacturing of sheet metal prototypes and parts in small quantities. Similar to other forming processes, the design of the SPIF process is a demanding task. Nowadays, the design process is usually performed using numerical simulations and virtual models.

Layer-by-layer bioassembly of poly(lactic) acid membranes loaded with coculture of HBMSCs and EPCs improves vascularization in vivo.

Layer-by-layer (LBL) BioAssembly method was developed to enhance the control of cell distribution within 3D scaffolds for tissue engineering applications. The objective of this study was to evaluate in vivo the development of blood vessels within LBL bioassembled membranes seeded with human primary cells, and to compare it to cellularized massive scaffolds. Poly(lactic) acid (PLA) membranes fabricated by fused deposition modeling were seeded with monocultures of human bone marrow stromal cells or with cocultures of these cells and endothelial progenitor cells.

Influence of the restorative procedure factors on stress values in premolar with MOD cavity: a finite element study.

In order to investigate the influence of cusp reduction, cavity isthmus width, and restorative material on stress values in premolar with mesio-occlusal-distal (MOD) cavity, numerical simulations were done on three-dimensional (3D) models of a maxillary second premolar designed using computerized tomography (CT) scan images. The use of four restorative materials (direct resin composite, direct resin composite with resin-modified glass-ionomer cement as the base, indirect resin composite, ceramic), three cavity preparation designs (without cusp coverage, 2-mm palatal cusp coverage, 2-mm palatal and buccal cusp coverage), and two cavity isthmus widths (1/2 and 2/3 intercuspal width) were simulated. After applying a static load of 200 N on the occlusal surface of the tooth, von Mises stresses in the enamel, dentin, and restoration were calculated using finite element analysis (FEA).

Influence of restorative procedures on endodontically treated premolars: Finite element analysis of a CT-scan based three-dimensional model.

An endodontically treated tooth with mesial-occlusal-distal (MOD) cavity is often restored with composite resin. Palatal and buccal cusp reduction (MODP, MODPB), and/or fiber-reinforced composite posts (P), are used in an attempt to improve the longevity of the restoration. The aim of this study was to determine the effects of these procedures on von Mises stress values and distribution in dental tissues and restorative materials using finite element analysis.

Layer-by-layer bioassembly of cellularized polylactic acid porous membranes for bone tissue engineering.

The conventional tissue engineering is based on seeding of macroporous scaffold on its surface ("top-down" approach). The main limitation is poor cell viability in the middle of the scaffold due to poor diffusion of oxygen and nutrients and insufficient vascularization. Layer-by-Layer (LBL) bioassembly is based on "bottom-up" approach, which considers assembly of small cellularized blocks.

Poly(methyl-methacrylate) nanocomposites with low silica addition.

Statement Of Problem: Poly(methyl-methacrylate) (PMMA) represents the most popular current denture material. However, its major drawbacks are insufficient ductility and strength.

Purpose: The purpose of this study was to improve the mechanical properties of PMMA in denture base application by adding small quantities of nanosilica.

Influence of cavity design preparation on stress values in maxillary premolar: a finite element analysis.

Aim: To analyze the influence of cavity design preparation on stress values in three-dimensional (3D) solid model of maxillary premolar restored with resin composite.

Methods: 3D solid model of maxillary second premolar was designed using computed-tomography (CT) data. Based on a factorial experiment, 9 different mesio-occlusal-distal (MOD) cavity designs were simulated, with three cavity wall thicknesses (1.