Comparative evaluation of intraoral scanners and a spectrophotometer for percent correct shade identification in clinical dentistry.

Objectives: The study aimed to assess the percent correct shade identification of four intraoral scanners (IOS) and a spectrophotometer, focusing on how reliably each device selects the correct tooth shade compared to a visual observer's selection. The research question addresses how much clinicians can trust the device-selected shade without visual verification.

Materials And Methods: Sixteen participants with natural, unrestored teeth were included.

A novel approach for the replacement of accuracy and precision measurements with the visual instrument agreement scale (VIAS) in evaluating the performance of four intraoral scanners and one shade measurement device.

Objectives: The terms 'accuracy' and 'precision' are tightly defined in color science but are often used ambiguously in dental research. This study introduces the visual instrument agreement scale (VIAS), a new method for determining visual-instrumental agreement in dental colorimetry by comparing visually perceived and measured color differences.

Materials And Methods: In-vivo tooth color measurements were taken from 16 participants using four intraoral scanners (Primescan, Medit i700, Carestream CS3700, Trios 3) and one spectrophotometer (Vita Easyshade V).

3D printed versus milled stabilization splints for the management of bruxism and temporomandibular disorders: study protocol for a randomized prospective single-blinded crossover trial.

Background: Nowadays, stabilization splints for the management of bruxism and temporomandibular disorders (TMD) can be produced utilizing a digital workflow comprising a digital impression of the teeth, digital splint design, and computer-aided manufacturing of the splints. The latter is usually a milling process, however, more recently 3D printing gained popularity due to its better cost and time efficiency. It remains unknown whether 3D printed stabilization splints are inferior to milled splints regarding clinical outcomes.

Bridging instrumental and visual perception with improved color difference equations: A multi-center study.

Objectives: This multicenter study aimed to evaluate visual-instrumental agreement of six color measurement devices and optimize three color difference equations using a dataset of visual color differences (∆V) from expert observers.

Methods: A total of 154 expert observers from 16 sites across 5 countries participated, providing visual scaling on 26 sample pairs of artificial teeth using magnitude estimation. Three color difference equations (ΔE*, ∆E, and CAM16-UCS) were tested.

Laser cooling ytterbium doped silica by 67 K from ambient temperature.

Laser cooling of a 5 cm long, 1 mm diameter ytterbium doped (6.56×10 ions/m) silica rod by 67 K from room temperature was achieved. For the pump source, a 100 W level ytterbium fiber amplifier was constructed along with a 1032 nm fiber Bragg grating seed laser.

Analysis of soft tissue integration-supportive cell functions in gingival fibroblasts cultured on 3D printed biomaterials for oral implant-supported prostheses.

To date, it is unknown whether 3D printed fixed oral implant-supported prostheses can achieve comparable soft tissue integration (STI) to clinically established subtractively manufactured counterparts. STI is mediated among others by gingival fibroblasts (GFs) and is modulated by biomaterial surface characteristics. Therefore, the aim of the present work was to investigate the GF response of a 3D printed methacrylate photopolymer and a hybrid ceramic-filled methacrylate photopolymer for fixed implant-supported prostheses in the sense of supporting an STI.

Polarization-resolved mode evolution in TMI-limited Yb-doped fiber amplifiers using a novel high-speed Stokes polarimeter.

In this work we have developed a high-speed Stokes polarimeter method based on simultaneous 4-channel imaging with a high-speed camera. Thus, current speed limitations of imaging polarimeters for wavelengths around 1 µm can be overcome, allowing a sub-ms polarization-resolved characterization of transverse mode instability (TMI). Additionally, the Stokes parameters of each individual mode are calculated by a simultaneous 4-beam mode reconstruction algorithm during post-processing and can be analyzed with unprecedented temporal resolution.

Fracture Resistance of a Two-Piece Zirconia Implant System after Artificial Loading and/or Hydrothermal Aging-An In Vitro Investigation.

Unlabelled: The purpose of the present study was to assess the fracture resistance of a two-piece alumina-toughened zirconia implant system with a carbon-reinforced PEEK abutment screw.

Methods: Thirty-two implants with screw-retained zirconia abutments were divided into four groups of eight samples each. Group 0 (control group) was neither loaded nor aged in a chewing simulator; group H was hydrothermally aged; group L was loaded with 98 N; and group HL was subjected to both hydrothermal aging and loading in a chewing simulator.

Mitigation of transverse mode instability by modal birefringence in polarization-maintaining fibers.

The effect of transverse mode instability (TMI) poses a fundamental obstacle for a further scaling of diffraction-limited, high-power fiber laser systems. In this work we present a theoretical and experimental study on the mitigation of TMI by modal birefringence in a polarization maintaining (PM) fiber. With the help of comprehensive simulations, we show that the thermally-induced refractive index grating responsible for TMI can be modified and washed out when light is coupled with a polarization input angle detuned from the main axes of the fiber.

TMI and polarization static energy transfer in Yb-doped low-NA PM fibers.

In this work, we conduct experimental investigations of transverse mode instabilities (TMI) in a large mode area ultra-low numerical aperture polarization maintaining fiber amplifier. This fiber is few mode in the slow-axis (conventional operation mode), but single mode in the fast-axis. We test the stability of the output beam by changing the input polarization angle and systematically investigate the transverse mode instability threshold in the two principal polarization axes.

Impact of site-selective spectroscopy on laser cooling parameter characterization.

From laser design to optical refrigeration, experimentally measured fluorescence spectra are often utilized to obtain input parameters for predictive models. However, in materials that exhibit site-selectivity, the fluorescence spectra depend on the excitation wavelength employed to take the measurement. This work explores different conclusions that predictive models reach after inputting such varied spectra.

Frequency-doubled Q-switched 4 × 4 multicore fiber laser system.

Frequency doubling of a Q-switched Yb-doped rod-type 4 × 4 multicore fiber (MCF) laser system is reported. A second harmonic generation (SHG) efficiency of up to 52% was achieved with type I non-critically phase-matched lithium triborate (LBO), with a total SHG pulse energy of up to 17 mJ obtained at 1 kHz repetition rate. The dense parallel arrangement of amplifying cores into a shared pump cladding enables a significant increase in the energy capacity of active fibers.

Long-Term Stability of Hydrothermally Aged and/or Dynamically Loaded One-Piece Diameter Reduced Zirconia Oral Implants.

The aim of this in vitro study was to evaluate the long-term stability of one-piece diameter reduced zirconia oral implants under the influence of loading and artificial aging in a chewing simulator as well as the fracture load in a static loading test. Thirty-two one-piece zirconia implants with a diameter of 3.6 mm were embedded according to the ISO 14801:2016 standard.

Potential of ytterbium doped silica glass for solid-state optical refrigeration to below 200 K.

We report on the optical refrigeration of ytterbium doped silica glass by >40 K starting at room temperature, which represents more than a two-fold improvement over the previous state-of-the-art. A spectroscopic investigation of the steady-state and time-dependent fluorescence was carried out over the temperature range 80 K to 400 K. The calculated minimum achievable temperature for our Yb doped silica sample is ≈150 K, implying the potential for utilizing ytterbium doped silica for solid-state optical refrigeration below temperatures commonly achieved by standard Peltier devices.

Influence of loading and aging on the fracture strength of an injection-molded two-piece zirconia implant restored with a zirconia abutment.

Objective: To investigate the fracture strength and potential phase transformation of an injection-molded two-piece zirconia implant restored with a zirconia abutment after loading and/or aging.

Methods: Thirty-two two-piece zirconia implants (4.0 mm diameter) restored with zirconia abutments were embedded according to ISO 14801 and divided into four groups (n = 8/group): Three groups were either exclusively hydrothermally treated (group HT; 85°C), dynamically loaded (group DL; 10  cycles; 98 N), or subjected to both treatments simultaneously (group DL/HT).

Zirconia fixed dental prostheses fabricated by 3D gel deposition show higher fracture strength than conventionally milled counterparts.

Zirconia restorations, which are fabricated by additive 3D gel deposition and do not require glazing like conventional restorations, were introduced as "self-glazed" zirconia restorations into dentistry. This in vitro investigation characterized the surface layer, microstructure and the fracture and aging behavior of "self-glazed" zirconia (Y-TZP) three-unit fixed dental prostheses (FDP) and compared them to conventionally CAD/CAM milled and glazed controls (Y-TZP-FDPs). For this purpose, the FDPs were analyzed by (focused ion beam) scanning electron microscopy, laserscanning microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and a dynamic and static loading test.

Laser cooling experiments to measure the quantum efficiency of Yb-doped silica fibers.

A detailed investigation into the wavelength-dependent cooling efficiencies of two ultra-pure large core diameter ytterbium-doped silica fibers is carried out by means of the laser-induced thermal modulation spectroscopy (LITMoS) method. From these measurements, an external quantum efficiency of 0.99 is obtained for both fibers.

Accuracy of additively manufactured zirconia four-unit fixed dental prostheses fabricated by stereolithography, digital light processing and material jetting compared with subtractive manufacturing.

Objective: To evaluate the manufacturing accuracy of zirconia four-unit fixed dental prostheses (FDPs) fabricated by three different additive manufacturing technologies compared with subtractive manufacturing.

Methods: A total of 79 zirconia FDPs were produced by three different manufacturing technologies, representing additive (one stereolithography [aSLA] and one material jetting [aMJ] device, two digital light processing [aDLP1/aDLP2] devices) and subtractive manufacturing (two devices [s1/s2]), the latter serving as references. After printing, additively manufactured FDPs were debound and finally sintered.

High-energy Q-switched 16-core tapered rod-type fiber laser system.

High-energy Q-switched master oscillator power amplifier systems based on rod-type 4 × 4 multicore fibers are demonstrated, achieving energy up to 49 mJ in ns-class pulses. A tapered fiber geometry is tested that maintains low mode order in large multimode output cores, improving beam quality in comparison to a similar fiber with no taper. The tapered fiber design can be scaled both in the number of amplifying cores and in the dimensions of the cores themselves, providing a potential route toward joule-class fiber lasers systems.

In Vitro Time Efficiency, Fit, and Wear of Conventionally- versus Digitally-Fabricated Occlusal Splints.

The purpose of the study was to compare conventional to digital workflows of occlusal splint production regarding time efficiency, overall fit, and wear. Fifteen Michigan splints were fabricated with a conventional and digital method. The duration for the dentist's and the dental technician's workload was recorded.

500 W rod-type 4 × 4 multicore ultrafast fiber laser.

We present a coherently combined femtosecond fiber chirped-pulse-amplification system based on a rod-type, ytterbium-doped, multicore fiber with 4 × 4 cores. A high average power of up to 500 W (after combination and compression) could be achieved at 10 MHz repetition rate with excellent beam quality. Additionally, < 500 fs pulses with up to 600 µJ of pulse energy were also realized with this setup.

Laser cooling of a Yb doped silica fiber by 18 Kelvin from room temperature.

An ytterbium doped silica optical fiber with a core diameter of 900µ has been cooled by 18.4 K below ambient temperature by pumping with 20 W of 1035 nm light in vacuum. In air, cooling by 3.

Air seal performance of personalized and statistically shaped 3D-printed face masks compared with market-available surgical and FFP2 masks.

The ongoing COVID-19 pandemic has revealed alarming shortages of personal protective equipment for frontline healthcare professionals and the general public. Therefore, a 3D-printable mask frame was developed, and its air seal performance was evaluated and compared. Personalized masks (PM) based on individual face scans (n = 8) and a statistically shaped mask (SSM) based on a standardized facial soft tissue shape computed from 190 face scans were designed.

Ultrashort pulse written fiber Bragg gratings as narrowband filters in multicore fibers.

We present the inscription of narrow-linewidth fiber Bragg gratings (FBGs) into different types of multicore fibers (MCFs) using ultrashort laser pulses and the phase mask technique, which can act as notch filters. Such filters are required, e.g.

Implementation of Laser-Induced Anti-Stokes Fluorescence Power Cooling of Ytterbium-Doped Silica Glass.

Laser cooling of a solid is achieved when a coherent laser illuminates the material, and the heat is extracted by annihilation of phonons resulting in anti-Stokes fluorescence. Over the past year, net solid-state laser cooling was successfully demonstrated for the first time in Yb-doped silica glass in both bulk samples and fibers. Here, we report more than 6 K of cooling below the ambient temperature, which is the lowest temperature achieved in solid-state laser cooling of silica glass to date to the best of our knowledge.