Aqueous-Based Fabrication of Low-VOC Nanostructured Block Copolymer Films as Potential Marine Antifouling Coatings.

The ability to fabricate nanostructured films by exploiting the phenomenon of microphase separation has made block copolymers an invaluable tool for a wide array of coating applications. Standard approaches to engineering nanodomains commonly involve the application of organic solvents, either through dissolution or annealing protocols, resulting in the release of volatile organic compounds (VOCs). In this paper, an aqueous-based method of fabricating low-VOC nanostructured block copolymer films is presented.

Self-seeding in one dimension: a route to uniform fiber-like nanostructures from block copolymers with a crystallizable core-forming block.

One-dimensional micelles formed by the self-assembly of crystalline-coil poly(ferrocenyldimethylsilane) (PFS) block copolymers exhibit self-seeding behavior when solutions of short micelle fragments are heated above a certain temperature and then cooled back to room temperature. In this process, a fraction of the fragments (the least crystalline fragments) dissolves at elevated temperature, but the dissolved polymer crystallizes onto the ends of the remaining seed fragments upon cooling. This process yields longer nanostructures (up to 1 μm) with uniform width (ca.

Phospholipid membrane encapsulation of nanoparticles for surface-enhanced Raman scattering.

Lipid-encapsulated surface-enhanced Raman scattering (SERS) nanoparticles, with promising applications in biomedical diagnostics, were produced. Gold nanoparticles, 60 nm in diameter, were coated with a ternary mixture of DOPC, sphingomyelin, and cholesterol. The lipid layer is versatile for engineering the chemical and optical properties of the particles.

Imaging secondary structure of individual amyloid fibrils of a β2-microglobulin fragment using near-field infrared spectroscopy.

Amyloid fibril diseases are characterized by the abnormal production of aggregated proteins and are associated with many types of neuro- and physically degenerative diseases. X-ray diffraction techniques, solid-state magic-angle spinning NMR spectroscopy, circular dichroism (CD) spectroscopy, and transmission electron microscopy studies have been utilized to detect and examine the chemical, electronic, material, and structural properties of amyloid fibrils at up to angstrom spatial resolution. However, X-ray diffraction studies require crystals of the fibril to be analyzed, while other techniques can only probe the bulk solution or solid samples.

The control of marine biofouling on xerogel surfaces with nanometer-scale topography.

Mixtures of n-octadecyltrimethoxysilane (C18, 1-5 mole-%), n-octyltriethoxysilane (C8) and tetraethoxysilane (TEOS) gave xerogel surfaces of varying topography. The 1:49:50 C18/C8/TEOS xerogel formed 100-400-nm-wide, 2-7-nm deep pores by AFM while coatings with ≥3% C18 were free of such features. Segregation of the coating into alkane-rich and alkane-deficient regions in the 1:49:50 C18/C8/TEOS xerogel was observed by IR microscopy.

Barnacle settlement and the adhesion of protein and diatom microfouling to xerogel films with varying surface energy and water wettability.

Previous work has shown that organosilica-based xerogels have the potential to control biofouling. In this study, modifications of chemistry were investigated with respect to their resistance to marine slimes and to settlement of barnacle cyprids. Adhesion force measurements of bovine serum albumin (BSA)-coated atomic force microscopy (AFM) tips to xerogel surfaces prepared from aminopropylsilyl-, fluorocarbonsilyl-, and hydrocarbonsilyl-containing precursors, indicated that adhesion was significantly less on the xerogel surfaces in comparison to a poly(dimethylsiloxane) elastomer (PDMSE) standard.

The role of surface energy and water wettability in aminoalkyl/fluorocarbon/hydrocarbon-modified xerogel surfaces in the control of marine biofouling.

Xerogel films with uniform surface topogrophy, as determined by scanning electron microscopy, atomic force microscopy (AFM), and time-of-flight secondary ion mass spectrometry, were prepared from aminopropylsilyl-, fluorocarbonsilyl-, and hydrocarbonsilyl- containing precursors. Young's modulus was determined from AFM indentation measurements. The xerogel coatings gave reduced settlement of zoospores of the marine fouling alga Ulva compared to a poly(dimethylsiloxane) elastomer (PDMSE) standard.

Insights into the composition, morphology, and formation of the calcareous shell of the serpulid Hydroides dianthus.

To date, the calcareous tubes of serpulid marine worms have not been studied extensively in a biomineralization context. The structure and composition of the tube shell and adhesive cement of the marine tubeworm Hydroides dianthus were studied using a variety of characterization techniques, including powder XRD, FTIR, SEM, EDX, and AFM. The tube and cement were determined to be inorganic-organic composite materials, consisting of inorganic aragonite (CaCO(3)) and Mg-calcite ((Ca(0.

Hierarchical structure formation of cylindrical brush polymer-surfactant complexes.

The complex formation of cylindrical brush polymers with poly(l-lysine) side chains (PLL) and sodium dodecyl sulfate (SDS) can induce a helical conformation of the cylindrical brush polymer in aqueous solution (Gunari, N.; Cong, Y.; Zhang, B.

Water-stable diblock polystyrene-block-poly(2-vinyl pyridine) and diblock polystyrene-block-poly(methyl methacrylate) cylindrical patterned surfaces inhibit settlement of zoospores of the green alga Ulva.

Nanopatterned surfaces with hydrophobic and hydrophilic domains were produced using the diblock copolymer polystyrene-block-poly(2-vinyl pyridine) (PS-b-P2VP) and polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA). The PS-b-P2VP diblock copolymer, mixed with the cross-linker benzophenone and spin-coated onto silicon wafers, showed self-assembled cylindrical structures, which were retained after UV treatment for cross-linking. The thin films displayed cylindrical domains after immersion in water.

Nanoscale structures and mechanics of barnacle cement.

Polymerized barnacle glue was studied by atomic force microscopy (AFM), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and chemical staining. Nanoscale structures exhibiting rod-shaped, globular and irregularly-shaped morphologies were observed in the bulk cement of the barnacle Amphibalanus amphitrite (=Balanus amphitrite) by AFM. SEM coupled with energy dispersive X-ray (EDX) provided chemical composition information, making evident the organic nature of the rod-shaped nanoscale structures.

Chemical imaging of the surface of self-assembled polystyrene-b-poly(methyl methacrylate) diblock copolymer films using apertureless near-field IR microscopy.

The nanoscale chemical composition variations of the surfaces of thin films of polystyrene- b-poly(methyl methacrylate) (PS- b-PMMA) diblock copolymers are investigated using apertureless near-field IR microscopy. The scattering of the incident infrared beam from a modulated atomic force microscopy (AFM) tip is probed using homodyne detection and demodulation at the tip oscillation frequency. An increase in the IR attenuation is observed in the PMMA-rich domains with a wavenumber dependence that is consistent with the bulk absorption spectrum.

Nanomechanical fingerprints of individual blocks of a diblock copolymer chain.

Atomic force microscopy (AFM)-based single polymer chain pulling experiments have been used to study the structural transitions of individual homopolymer chains in water. Polystyrene (PS) showed a three-regime force-extension profile exhibiting a force plateau reminiscent of a first-order transition, as predicted theoretically, whereas poly(methyl methacrylate) (PMMA) showed a characteristic saw-tooth pattern reminiscent of multidomain disassembly behavior. The two distinct structural transtions provide fingerprints for the individual homopolymers, which can be used to identify individual blocks of symmetric and asymmetric PS- b-PMMA diblock copolymer chains.