Copper-Nickel/SiC composites for applications on contact electrodes.

Novel copper-nickel matrix composites reinforced with silicon carbide (SiC) micro particles for metal contact applications were manufactured by powder metallurgy technology and were experimentally characterized. Cu and Cu alloys are commonly used as metal contact for either vacuum, oil, or SF6 in low-voltage circuit breaker devices, but their application in environments with the presence of oxygen is limited due to their tendency to form high-resistance copper oxides. Thus, the addition of Ni as an alloying element provides resistance to both humidity and several corrosive environments and increases the composites' hardness, mechanical strength, and wear resistance.

β-Phase Enhancement of Force Spun Composite Nanofibers for Sensing Applications.

In this study, a piezoelectric harvesting device was developed using polyvinylidene fluoride (PVDF) nanofibers reinforced with either BaTiO nanoparticles or graphene powder. BaTiO nanoparticles were synthesized through the sol-gel method with an average size of approximately 32 nm. The PVDF nanofibers, along with the nanoparticle composites in an acetone-N,N-dimethylformamide mixture, were produced using a centrifugal Forcespinning™ machine, resulting in a heterogeneous arrangement of fiber meshes, with an average diameter of 1.

Toward the Industrial Application of Aluminum-Based Nanocomposite Material: A Study of Zn-Plating Process in Circuit Breaker Application.

This article explores the industrial application of an Al-based nanocomposite reinforced with 0.5 wt.% of multiwalled carbon nanotubes with a Zn mechanical plating applied to fulfill the field requirements of electrical devices.

Spark Plasma Sintering of Aluminum Nanocomposite Powders: Recent Strategy to Translate from Lab-Scale to Mass Production.

The aim of this paper focuses on presenting a recent study that describes the fundamental steps needed to effectively scale-up from lab to mass production parts produced from Al powders reinforced with 0.5 wt% of industrial multiwalled carbon nanotubes (MWCNTs), with mechanical and electrical conductivity properties higher that those measured at the lab scale. The produced material samples were produced via a Spark Plasma Sintering (SPS) process using nanocomposite aluminum powders elaborated with a planetary ball-mill at the lab scale, and high-volume attrition milling equipment in combination with controlled atmosphere sinter hardening furnace equipment, which were used to consolidate the material at the industrial level.

Enhancement of Electrical Conductivity of Aluminum-Based Nanocomposite Produced by Spark Plasma Sintering.

This article focuses on exploring how the electrical conductivity and densification properties of metallic samples made from aluminum (Al) powders reinforced with 0.5 wt % concentration of multi-walled carbon nanotubes (MWCNTs) and consolidated through spark plasma sintering (SPS) process are affected by the carbon nanotubes dispersion and the Al particles morphology. Experimental characterization tests performed by scanning electron microscopy (SEM) and by energy dispersive spectroscopy (EDS) show that the MWCNTs were uniformly ball-milled and dispersed in the Al surface particles, and undesirable phases were not observed in X-ray diffraction measurements.

Spark Plasma Sintering of Aluminum-Based Powders Reinforced with Carbon Nanotubes: Investigation of Electrical Conductivity and Hardness Properties.

This paper focuses on reporting results obtained by the spark plasma sintering (SPS) consolidation and characterization of aluminum-based nanocomposites reinforced with concentrations of 0.5 wt%, 1 wt% and 2 wt% of single-walled carbon nanotubes (SWCNTs) and multi-walled carbon nanotubes (MWCNTs). Experimental characterization performed by SEM shows uniform carbon nanotube (CNT) dispersion as well as carbon clusters located in the grain boundary of the Al matrix.

Advances in the Processing of UHMWPE-TiO to Manufacture Medical Prostheses via SPIF.

This research focuses on developing a novel ultra high molecular weight polyethylene (UHMWPE) material reinforced with titanium dioxide (TiO 2 ) nanoparticles for producing craniofacial prostheses via an incremental sheet forming process (SPIF). First, UHMWPE-TiO 2 nanocomposite sheets were produced using incipient wetting and the compression molding process by considering different concentrations of TiO 2 nanoparticles. Then, the influence that the compression molding fabrication process has on the crystallinity and structural properties of the produced sample sheets was investigated.

Development, Fabrication, and Characterization of Composite Polycaprolactone Membranes Reinforced with TiO Nanoparticles.

This paper focuses on developing, fabricating, and characterizing composite polycaprolactone (PCL) membranes reinforced with titanium dioxide nanoparticles (NPs) elaborated by using two solvents; acetic acid and a mixture of chloroform and N,N-dimethylformamide (DMF). The resulting physical, chemical, and mechanical properties of the composite materials are studied by using experimental characterization techniques such as scanning electron microscopy (SEM), differential scanning calorimetry (DSC), X-Ray diffraction (XRD), Fourier-transform infrared (FTIR) analysis, contact angle (CA), uniaxial and biaxial tensile tests, and surface roughness measurements. Experimental results show that the composite material synthesized by sol-gel and chloroform-DMF has a better performance than the one obtained by using acetic acid as a solvent.