Brain-Implantable Multifunctional Probe for Simultaneous Detection of Glutamate and GABA Neurotransmitters: Optimization and In Vivo Studies.

Imbalances in levels of glutamate (GLU) and gamma-aminobutyric acid (GABA) and their sub-second signaling dynamics occur in several brain disorders including traumatic brain injury, epilepsy, and Alzheimer's disease. The present work reports on the optimization and in vivo testing of a silicon (Si) multifunctional biosensor probe for sub-second simultaneous real-time detection of GLU and GABA. The Si probe features four surface-functionalized platinum ultramicroelectrodes (UMEs) for detection of GLU and GABA, a sentinel site, and integrated microfluidics for in-situ calibration.

Brain-Implantable Multifunctional Probe for Simultaneous Detection of Glutamate and GABA Neurotransmitters.

Glutamate (GLU) and gamma-aminobutyric acid (GABA) are neurotransmitters (NTs) with an essential role in signal transmission in the brain. Brain disorders, such as epilepsy, Alzheimer's and Parkinson's diseases, and traumatic brain injury can be linked to imbalances in the GLU-GABA homeostasis that occurs in sub-second to seconds time frames. Current measurement techniques can detect these two NT concentrations simultaneously only .

Approaching the Strain-Free Limit in Ultrathin Nanomechanical Resonators.

Ultrathin mechanical structures are ideal building platforms to pursue the ultimate limit of nanomechanical resonators for applications in sensing, signal processing, and quantum physics. Unfortunately, as the thickness of the vibrating structures is reduced, the built-in strain of the structural materials plays an increased role in determining the mechanical performance of the devices. As a consequence, it is very challenging to fabricate resonators working in the modulus-dominant regime, where their dynamic behavior is exclusively determined by the device geometry.

Nonlinear Mode Coupling and One-to-One Internal Resonances in a Monolayer WS Nanoresonator.

Nanomechanical resonators make exquisite force sensors due to their small footprint, low dissipation, and high frequencies. Because the lowest resolvable force is limited by ambient thermal noise, resonators are either operated at cryogenic temperatures or coupled to a high-finesse optical or microwave cavity to reach sub aN Hz sensitivity. Here, we show that operating a monolayer WS nanoresonator in the strongly nonlinear regime can lead to comparable force sensitivities at room temperature.

Diamond coated artificial cardiovascular devices.

Ultrananocrystalline diamond (UNCD), an extremely smooth, low cost diamond coating was successfully developed herein for antithrombogenic application which requires high biocompatibility, low wear, low friction, and chemical inertness. The substrate materials utilized in the Jarvik 2000 ventricular assist device (VAD), silicon carbide and titanium alloy, provide an excellent substrate match for UNCD integration. The paper addresses the development of medical-quality UNCD films to significantly improve the knowledge base regarding the defect mechanisms of UNCD films, to reduce or eliminate known wear-inducing imperfections in the film, and to thoroughly characterize and test the films as well as assembled UNCD-coated VADs.

Ultrananocrystalline Diamond Integration with Pyrolytic Carbon Components of Mechanical Heart Valves.

In this report, an idea of integrating ultrananocrystalline diamond (UNCD) with pyrolytic carbon (PyC) -based mechanical heart valves, has been demonstrated. The report addresses the strategies to avoid graphitization and film delamination during the diamond coating. Raman and scratch tests showed that a UNCD film with high purity could adhere to the PyC substrate strongly.

Ultrananocrystalline diamond tip integrated onto a heated atomic force microscope cantilever.

We report a wear-resistant ultrananocrystalline (UNCD) diamond tip integrated onto a heated atomic force microscope (AFM) cantilever and UNCD tips integrated into arrays of heated AFM cantilevers. The UNCD tips are batch-fabricated and have apex radii of approximately 10 nm and heights up to 7 μm. The solid-state heater can reach temperatures above 600 °C and is also a resistive temperature sensor.

A quantitative study of detection mechanism of a label-free impedance biosensor using ultrananocrystalline diamond microelectrode array.

It is well recognized that label-free biosensors are the only class of sensors that can rapidly detect antigens in real-time and provide remote environmental monitoring and point-of-care diagnosis that is low-cost, specific, and sensitive. Electrical impedance spectroscopy (EIS) based label-free biosensors have been used to detect a wide variety of antigens including bacteria, viruses, DNA, and proteins due to the simplicity of their detection technique. However, their commercial development has been hindered due to difficulty in interpreting the change in impedance upon antigen binding and poor signal reproducibility as a result of surface fouling and non-specific binding.

Nanofountain-probe-based high-resolution patterning and single-cell injection of functionalized nanodiamonds.

Nanodiamonds are rapidly emerging as promising carriers for next-generation therapeutics and drug delivery. However, developing future nanoscale devices and arrays that harness these nanoparticles will require unrealized spatial control. Furthermore, single-cell in vitro transfection methods lack an instrument that simultaneously offers the advantages of having nanoscale dimensions and control and continuous delivery via microfluidic components.

Direct deposition and assembly of gold colloidal particles using a nanofountain probe.

We report the direct delivery and assembly of negatively charged gold colloidal particles atop positively charged amino-terminated silicon oxide surfaces using a nanofountain atomic force microscopy probe. The experimental results and fluid simulations indicate that the flow of nanoparticles is confined to the core tip region of the probe. This leads to the assembly of high-resolution submicron patterns (200 nm) on the substrate with feature sizes dependent on the tip-substrate contact time.

Novel ultrananocrystalline diamond probes for high-resolution low-wear nanolithographic techniques.

A hard, low-wear probe for contact-mode writing techniques, such as dip-pen nanolithography (DPN), was fabricated using ultrananocrystalline diamond (UNCD). Molding within anisotropically etched and oxidized pyramidal pits in silicon was used to obtain diamond tips with radii down to 30 nm through growth of UNCD films followed by selective etching of the silicon template substrate. The probes were monolithically integrated with diamond cantilevers and subsequently integrated into a chip body obtained by metal electroforming.