Fabrication and Characterization of 2D Nonlinear Structures Based on DAST Nanocrystals and SU-8 Photoresist for Terahertz Application.

We demonstrate a method for the realization of highly nonlinear optical 4-(4-dimethylaminostyryl)- 1-methylpyridinium tosylate (DAST) two-dimensional structures by a double-step technique. The desired polymeric structures were first fabricated by using the multiple exposure of the two-beam interference technique, and the DAST nanoscrystals were then prepared inside the air-voids of these photoresist templates, resulting in nonlinear periodic structures. The nonlinear properties were characterized by optical and scanning microscopies, as well as by second-harmonic generation technique.

High-directivity far-field radiation of quantum dot-based single-photon emitter coupled to polymeric circular waveguide resonant grating.

Solid-state single-photon emitters (SPEs) commonly encounter the limitation of quasi-omnidirectional radiation patterns, which poses challenges in utilizing their emission with conventional optical instruments. In this study, we demonstrate the tailoring of the far-field radiation patterns of SPEs based on colloidal quantum dots (QDs), both theoretically and experimentally, by employing a polymer-based dielectric antenna. We introduce a simple and cost-effective technique, namely low one-photon absorption direct laser writing, to achieve precise coupling of a QD into an all-polymer circular waveguide resonance grating.

Optofluidic Sensor Based on Polymer Optical Microresonators for the Specific, Sensitive and Fast Detection of Chemical and Biochemical Species.

The accurate, rapid, and specific detection of DNA strands in solution is becoming increasingly important, especially in biomedical applications such as the trace detection of COVID-19 or cancer diagnosis. In this work we present the design, elaboration and characterization of an optofluidic sensor based on a polymer-based microresonator which shows a quick response time, a low detection limit and good sensitivity. The device is composed of a micro-racetrack waveguide vertically coupled to a bus waveguide and embedded within a microfluidic circuit.

Design and Realization of Polymeric Waveguide/Microring Structures for Telecommunication Domain.

Polymer-based micro-optical components are very important for applications in optical communication. In this study, we theoretically investigated the coupling of polymeric waveguide and microring structures and experimentally demonstrated an efficient fabrication method to realize these structures on demand. First, the structures were designed and simulated using the FDTD method.

On-Chip 3D Printing of Polymer Waveguide-Coupled Single-Photon Emitter Based on Colloidal Quantum Dots.

In the field of quantum technology, there has been a growing interest in fully integrated systems that employ single photons due to their potential for high performance and scalability. Here, a simple method is demonstrated for creating on-chip 3D printed polymer waveguide-coupled single-photon emitters based on colloidal quantum dots (QDs). By using a simple low-one photon absorption technique, we were able to create a 3D polymeric crossed-arc waveguide structure with a bright QD on top.

Direct Synthesis of Gold Nanoparticles in Polymer Matrix.

We report an original method for directly fabricating gold nanoparticles (Au NPs) in a polymer matrix using a thermal treatment technique and theoretically and experimentally investigate their plasmonic properties. The polymeric-metallic nanocomposite samples were first prepared by simply mixing SU-8 resist and Au salt with different concentrations. The Au NPs growth was triggered inside the polymer through a thermal process on a hot plate and in air environment.

Direct fabrication and characterization of gold nanohole arrays.

We demonstrate a one-step fabrication method to realize desired gold (Au) nanoholes arrays by using a one-photon absorption based direct laser writing technique. Thanks to the optically induced thermal effect of Au material at 532 nm excitation wavelength, the local temperature at the laser focus area can reach as high as 600°C, which induces an evaporation of the Au thin film resulting in a metallic nanohole. By controlling the laser spot movement and exposure time, different two-dimensional Au nanoholes structures with periodicity as small as 500 nm have been demonstrated.

Positive role of the long luminescence lifetime of upconversion nanophosphors on resonant surfaces for ultra-compact filter-free bio-assays.

We introduce a compact array fluorescence sensor principle that takes advantage of the long luminescence lifetimes of upconversion nanoparticles (UCNPs) to deploy a filter-free, optics-less contact geometry, advantageous for modern biochemical assays of biomolecules, pollutants or cells. Based on technologically mature CMOS chips for ∼10 kHz technical/scientific imaging, we propose a contact geometry between assayed molecules or cells and a CMOS chip that makes use of only a faceplate or direct contact, employing time-window management to reject the 975 nm excitation light of highly efficient UCNPs. The chip surface is intended to implement, in future devices, a resonant waveguide grating (RWG) to enhance excitation efficiency, aiming at the improvement of upconversion luminescence emission intensity of UCNP deposited atop of such an RWG structure.

Controllable movement of single-photon source in multifunctional magneto-photonic structures.

Quantum dot (QD) coupling in nanophotonics has been widely studied for various potential applications in quantum technologies. Micro-machining has also attracted substantial research interest due to its capacity to use miniature robotic tools to make precise controlled movements. In this work, we combine fluorescent QDs and magnetic nanoparticles (NPs) to realize multifunctional microrobotic structures and demonstrate the manipulation of a coupled single-photon source (SPS) in 3D space via an external magnetic field.

Photostability and long-term preservation of a colloidal semiconductor-based single photon emitter in polymeric photonic structures.

Colloidal semiconductor quantum dots (QDs) are promising candidates for various applications in electronics and quantum optics. However, they are sensitive and vulnerable to the chemical environment due to their highly dynamic surface with a large portion of exposed atoms. Hence, oxidation and detrimental defects on the nanocrystal (NC) interface dramatically deteriorate their optical as well as electrical properties.

Enhancement of Rhodamine B Degradation by Ag Nanoclusters-Loaded g-C₃N₄ Nanosheets.

In this paper, silver (Ag) nanoclusters-loaded graphitic carbon nitride (g-C₃N₄) nanosheets are synthesized and their physical properties as well as photocatalytic activities are systematically investigated by different techniques. The existence of Ag atoms in the form of nanoclusters (NCs) rather than well-crystallized nanoparticles are evidenced by X-ray diffraction patterns, SEM images, and XPS spectra. The deposition of Ag nanoclusters on the surface of g-C₃N₄ nanosheets affect the crystal structure and slightly reduce the band gap energy of g-C₃N₄.

Rapid direct laser writing of desired plasmonic nanostructures.

We demonstrate a direct way to realize arbitrary gold nanostructures via a local dewetting method. This technique was based on the optically induced local thermal effect at the focusing region of a direct laser writing (DLW) system employing a green continuous-wave laser. The local high temperature allowed the creation of gold nano-islands only at the focusing area of the optical system.

High second-order nonlinear response of platinum nanoflowers: the role of surface corrugation.

Platinum nanoflowers (PtNFs) were elaborated using the seed-mediated growth technique applied to monodisperse platinum nanoparticles (∼3.0 nm) synthesized by the chemical reduction method. The X-ray diffraction pattern confirmed the formation of face-centered-cubic platinum nanocrystals.

Concept for three-dimensional optical addressing by ultralow one-photon absorption method.

With respect to experimental condition, we have investigated the point spread function of a high numerical aperture objective lens, taking into account the absorption effect of the studied material. By using a material possessing an ultralow one-photon absorption (LOPA) coefficient at the excitation wavelength, the light beam can penetrate deeply inside the material and be tightly focused into a subwavelength spot, almost the same as in the absence of material. Combining tight focusing and ultralow absorption conditions, we show that LOPA-based microscopy is thus capable of three-dimensional imaging and fabrication with long penetration depth up to 300 μm.

Submicrometer 3D structures fabrication enabled by one-photon absorption direct laser writing.

We demonstrate a new 3D fabrication method to achieve the same results as those obtained by the two-photon excitation technique, by using a simple one-photon elaboration method in a very low absorption regime. Desirable 2D and 3D submicrometric structures, such as spiral, chiral, and woodpile architectures, with feature size as small as 190 nm have been fabricated, by using just a few milliwatts of a continuous-wave laser at 532 nm and a commercial SU8 photoresist. Different aspects of the direct laser writing based on ultralow one-photon absorption (LOPA) technique are investigated and compared with the TPA technique, showing several advantages, such as simplicity and low cost.

Fabrication of three-dimensional polymer quadratic nonlinear grating structures by layer-by-layer direct laser writing technique.

We demonstrate the fabrication of a three-dimensional (3D) polymer quadratic nonlinear (χ(2)) grating structure. By performing layer-by-layer direct laser writing (DLW) and spin-coating approaches, desired photobleached grating patterns were embedded in the guest-host dispersed-red-1/poly(methylmethacrylate) (DR1/PMMA) active layers of an active-passive alternative multilayer structure through photobleaching of DR1 molecules. Polyvinyl-alcohol and SU8 thin films were deposited between DR1/PMMA layers serving as a passive layer to separate DR1/PMMA active layers.

Fabrication of ellipticity-controlled microlens arrays by controlling the parameters of the multiple-exposure two-beam interference technique.

We demonstrate a promising method for fabrication of plastic microlens arrays (MLAs) with a controllable ellipticity and structure, by using the combination of multiple-exposure two-beam interference and plastic replication techniques. Multiple exposures of a two-beam interference pattern with a wavelength of 442 nm into a thick positive photoresist (AZ-4620) were used to form different two-dimensional periodic structures. Thanks to the developing effect of the positive photoresist, fabricated structures consisting of hemielliptical- or hemispherical-shaped concave holes were obtained.

Fabrication of microlens arrays based on the mass transport effect of SU-8 photoresist using a multiexposure two-beam interference technique.

Microlens arrays (MLAs) were fabricated based on the mass transport effect of SU-8 photoresist by a multiexposure two-beam interference technique. In particular, a direct single-step fabrication process, i.e.

Fabrication of periodic nanovein structures by holography lithography technique.

This work demonstrates a promising method to fabricate periodic nanovein structures, which can be served as templates for fabricating photonic crystals possessing a large complete photonic bandgap. First, the fabrication of a one-dimensional grating structure connected with nanolines is demonstrated by controlling the exposure dosage of the second exposure of the two-exposure two-beam interference technique. Secondly, by using the same interference technique but setting each exposure under the same exposure dosage, two-dimensional periodic structures with nanovein connections were fabricated.

Fabrication of spatial modulated second order nonlinear structures and quasi-phase matched second harmonic generation in a poled azo-copolymer planar waveguide.

This work demonstrates that arbitrary types of spatially modulated second-order susceptibility (chi((2)) structures such as 1D and 2D, periodic and quasi-periodic structures can be obtained by using the combination of corona poling and direct laser writing (DLW) techniques. The fabrication technique is based on the photodepoling of azo-dye molecules caused by one-photon or two-photon absorption during the DLW process. Polarization and second harmonic generation (SHG) images of the fabricated structures were measured by electrostatic force microscope and SHG mapping techniques, respectively.

Fabrication of highly rotational symmetric quasi-periodic structures by multiexposure of a three-beam interference technique.

A simple and efficient interference method for fabricating highly symmetric two-dimensional (2-D) quasi-periodic structures (QPSs) is theoretically and experimentally demonstrated. With a three-beam interference technique, one can fabricate a periodic 2-D structure having sixfold symmetry. When this structure is multiduplicated into other specific orientations its combination results in a QPS with multifold symmetry.

Fabrication of two- and three-dimensional quasi-periodic structures with 12-fold symmetry by interference technique.

We demonstrate theoretically and experimentally a useful technique for fabrication of two- and three-dimensional (2D or 3D) quasi-periodic structures by a double-exposure of a periodic interference pattern. With three-beam and three-beam-plus-one interference techniques, one can fabricate a periodic 2D and 3D structure having six-fold symmetry, respectively. When this structure is duplicated in another orientation, its combination results in a quasi-periodic twelve-fold symmetry structure.

Precisely introducing defects into periodic structures by using a double-step laser scanning technique.

We demonstrate a promising method to precisely introduce desired defects into large-area periodic structures by using a double-step laser scanning technique. A multiexposure two-beam interference technique is first used to create 2D periodic structures. A low power femtosecond laser combined with a high numerical aperture objective lens is then used to map the periodic structures to determine the positions and orientations of air holes or material cylinders without intermediate development.

Fabrication of two- and three-dimensional periodic structures by multi-exposure of two-beam interference technique.

A simple and efficient optical interference method for fabricating high quality two- and three-dimensional (2D and 3D) periodic structures is demonstrated. Employing multi-exposure of two-beam interference technique, different types of periodic structures are created depending on the number of exposure and the rotation angle of the sample for each exposure. Square and hexagonal 2D structures are fabricated by a multi-exposure of two-beam interference pattern with a rotation angle of 90 masculine and 60 masculine between two different exposures, respectively.