Patch-Type Vibration Visualization (PVV) Sensor System Based on Triboelectric Effect.

Self-powered wireless sensor systems have emerged as an important topic for condition monitoring in nuclear power plants. However, commercial wireless sensor systems still cannot be fully self-sustainable due to the high power consumption caused by excessive signal processing in a mini-electronic computing system. In this sense, it is essential not only to integrate the sensor system with energy-harvesting devices but also to develop simple data processing methods for low power schemes.

Methodologies for Fabricating Flexible Supercapacitors.

The spread of wearable and flexible electronics devices has been accelerating in recent years for a wide range of applications. Development of an appropriate flexible power source to operate these flexible devices is a key challenge. Supercapacitors are attractive for powering portable lightweight consumer devices due to their long cycle stability, fast charge-discharge cycle, outstanding power density, wide operating temperatures and safety.

A nanoscale vacuum field emission gated diode with an umbrella cathode.

A nanoscale field emission vacuum channel gated diode structure is proposed and a tungsten cathode with an umbrella-like geometry and sharp vertical edge is fabricated. The edge of the suspended cathode becomes the field emission surface. Unlike in the traditional transistor with the gate typically located between the source and the drain, the bottom silicon plate becomes the gate here and the anode terminal is located between the umbrella cathode and the gate.

Printable Gel Polymer Electrolytes for Solid-State Printed Supercapacitors.

Supercapacitors prepared by printing allow a simple manufacturing process, easy customization, high material efficiency and wide substrate compatibility. While printable active layers have been widely studied, printable electrolytes have not been thoroughly investigated despite their importance. A printable electrolyte should not only have high ionic conductivity, but also proper viscosity, small particle size and chemical stability.

All 3D-Printed Flexible ZnO UV Photodetector on an Ultraflat Substrate.

An all three-dimensional (3D)-printed flexible ZnO ultraviolet (UV) photodetector is demonstrated, where the 3D-printing method is used not only for the electrode and photosensitive material but also for creating a substrate. An ultraflat and flexible substrate capable of serving as the backbone layer is developed using a water-dissolvable polymer layer for surface planarization. A two-layered printing followed by surface treatment is demonstrated for the substrate preparation.

On-Demand Printing of Wearable Thermotherapy Pad.

Thermotherapy is an effective method for pain relief, recovery from injury, and general healthcare. The ordinary heat pad used for thermotherapy at home is not usually tailored to the individual but supplied in a few different pre-fixed sizes and shapes for mass marketing. A customized wearable heat pad often requires expert support.

Electrically-generated memristor based on inkjet printed silver nanoparticles.

A method to electrically induce memristor performance from inkjet-printed silver (Ag) nanoparticles is presented, which is effective on a specifically designed hourglass-shaped Ag metal device. Joule heating-induced oxidation in the bottleneck region, when applying a high current to the device, results in a metal-electrolyte-metal structure produced from just a single metal ink for the memristor operation. This electrically induced memristor shows a nonuniform dispersion of the Ag nanoparticles within the oxide electrolyte layer, depending on the bias polarity adopted during the initial metal rupture process.

Carbon Nanotube Based γ Ray Detector.

A single walled carbon nanotube (SWCNT) based γ ray detector is demonstrated without a conventional scintillation mechanism. The change in the conductance of a two terminal SWCNT resistor in response to γ ray exposure is exploited as a sensing mechanism. Radiation-induced ambient oxygen dissociation and subsequent adsorption of oxygen species on the SWCNT surface alter its electrical properties.

Wearable UV Sensor Based on Carbon Nanotube-Coated Cotton Thread.

A fabric-compatible UV sensor is presented using a cellulose-based thread coated with single-wall carbon nanotube ink. Two-terminal resistive responses of the thread were measured upon exposure to UV, and the effects of intensity, wavelength, and on/off cycling were studied. The sensor was tested in the field under direct sunlight, demonstrating practical usability for a wearable/flexible UV sensor system.

A Single Input Multiple Output (SIMO) Variation-Tolerant Nanosensor.

Successful transition to commercialization and practical implementation of nanotechnology innovations may very well need device designs that are tolerant to the inherent variations and imperfections in all nanomaterials including carbon nanotubes, graphene, and others. As an example, a single-walled carbon nanotube network based gas sensor is promising for a wide range of applications such as environment, industry, and biomedical and wearable devices due to its high sensitivity, fast response, and low power consumption. However, a long-standing issue has been the production of extremely high purity semiconducting nanotubes, thereby contributing to the delay in the market adoption of those sensors.

Physically Transient Memory on a Rapidly Dissoluble Paper for Security Application.

We report the transient memory device by means of a water soluble SSG (solid sodium with glycerine) paper. This material has a hydroscopic property hence it can be soluble in water. In terms of physical security of memory devices, prompt abrogation of a memory device which stored a large number of data is crucial when it is stolen because all of things have identified information in the memory device.

Electrothermal Annealing (ETA) Method to Enhance the Electrical Performance of Amorphous-Oxide-Semiconductor (AOS) Thin-Film Transistors (TFTs).

An electro-thermal annealing (ETA) method, which uses an electrical pulse of less than 100 ns, was developed to improve the electrical performance of array-level amorphous-oxide-semiconductor (AOS) thin-film transistors (TFTs). The practicality of the ETA method was experimentally demonstrated with transparent amorphous In-Ga-Zn-O (a-IGZO) TFTs. The overall electrical performance metrics were boosted by the proposed method: up to 205% for the trans-conductance (gm), 158% for the linear current (Ilinear), and 206% for the subthreshold swing (SS).

Logic circuits composed of flexible carbon nanotube thin-film transistor and ultra-thin polymer gate dielectric.

Printing electronics has become increasingly prominent in the field of electronic engineering because this method is highly efficient at producing flexible, low-cost and large-scale thin-film transistors. However, TFTs are typically constructed with rigid insulating layers consisting of oxides and nitrides that are brittle and require high processing temperatures, which can cause a number of problems when used in printed flexible TFTs. In this study, we address these issues and demonstrate a method of producing inkjet-printed TFTs that include an ultra-thin polymeric dielectric layer produced by initiated chemical vapor deposition (iCVD) at room temperature and highly purified 99.

Single nanowire on graphene (SNOG) as an efficient, reproducible, and stable SERS-active platform.

Developing a well-defined nanostructure that can provide strong, reproducible, and stable SERS signals is quite important for the practical application of surface-enhanced Raman scattering (SERS) sensors. We report here a novel single nanowire (NW) on graphene (SNOG) structure as an efficient, reproducible, and stable SERS-active platform. Au NWs having a well-defined single-crystal geometry on a monolayer graphene-coated metal film can form a well-defined, continuous nanogap structure that provides extremely reproducible and stable SERS signals.

Controllable electrical and physical breakdown of poly-crystalline silicon nanowires by thermally assisted electromigration.

The importance of poly-crystalline silicon (poly-Si) in semiconductor manufacturing is rapidly increasing due to its highly controllable conductivity and excellent, uniform deposition quality. With the continuing miniaturization of electronic components, low dimensional structures such as 1-dimensional nanowires (NWs) have attracted a great deal of attention. But such components have a much higher current density than 2- or 3-dimensional films, and high current can degrade device lifetime and lead to breakdown problems.

Floating Oscillator-Embedded Triboelectric Generator for Versatile Mechanical Energy Harvesting.

A versatile vibration energy harvesting platform based on a triboelectricity is proposed and analyzed. External mechanical vibration repeats an oscillating motion of a polymer-coated metal oscillator floating inside a surrounding tube. Continuous sidewall friction at the contact interface of the oscillator induces current between the inner oscillator electrode and the outer tube electrode to convert mechanical vibrations into electrical energy.

Surface Engineering of Triboelectric Nanogenerator with an Electrodeposited Gold Nanoflower Structure.

A triboelectric nanogenerator composed of gold nanoflowers is demonstrated. The proposed triboelectric nanogenerator creates electricity by contact-separation-based electrification between an anodic metal and a cathodic polymer. For the improvement of output power via the enlargement of the effective surface area in the anodic metal, gold nanoflowers that produce a hierarchical morphology at a micro-to-nano scale by electrodeposition are utilized.

Nature-replicated nano-in-micro structures for triboelectric energy harvesting.

Triboelectric nanogenerators with nature-replicated interface structures are presented. Effective contact areas of the triboelectric surfaces are largely enhanced because of the densely packed nano-in-micro hierarchical structures in nature. The enlarged contact area causes stronger triboelectric charge density, which results in output power increment.

A mechanical and electrical transistor structure (METS) with a sub-2 nm nanogap for effective voltage scaling.

A mechanical and electrical transistor structure (METS) is proposed for effective voltage scaling. The sub-2 nm nanogap by atomic layer deposition (ALD) without stiction and the application of a dielectric with high-permittivity allowed the pull-in voltage of sub-2 V, showing the strength of the mechanical actuation that is hard to realize in a typical complementary metal-oxide-semiconductor (CMOS) transistor. The results are verified by simulation and interpreted by the numerical equation.

Design strategy for a piezoelectric nanogenerator with a well-ordered nanoshell array.

The piezoelectric nanogenerator (PNG) has been spotlighted as a promising candidate for use as a sustainable power source in wireless system applications. For the further development of PNGs, structural optimization is essential, but the structural analysis progress in this area has been scant. In the present study, we proposed a PNG with a well-ordered nanoshell array structure.

Sensitive and selective electrochemical detection of dopamine using an electrode modified with carboxylated carbonaceous spheres.

A highly sensitive and selective electrochemical sensor of dopamine (DA) has been developed by employing carboxylated carbonaceous spheres to modify glassy carbon electrodes (GCEs). Scanning electron microscopy (SEM) and Fourier transform infrared (FT-IR) spectroscopy were used to characterize as-prepared carbonaceous spheres. The results show that the diameter of carboxylated carbonaceous spheres is uniformly 500 nm and that their surfaces mainly expose carboxyl groups with negative charges.

Hollow CuO nanospheres uniformly anchored on porous Si nanowires: preparation and their potential use as electrochemical sensors.

Hollow CuO nanospheres have been prepared via a reduction reaction of copper ions on porous Si nanowires combined with calcination in air and uniformly anchored on their surfaces. Scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) were employed to characterize and analyze as-synthesized samples. The results reveal that Si nanowires fabricated from heavily doped Si wafer are formed with a meso-porous structure by an Ag-assisted etching approach, and Cu nanoparticles are formed and uniformly decorated on the Si nanowires through a reaction of copper ions reduced by silicon.

Self-aligned nanoforest in silicon nanowire for sensitive conductance modulation.

A self-aligned and localized nanoforest structure is constructed in a top-down fabricated silicon nanowire (SiNW). The surface-to-volume ratio (SVR) of the SiNW is enhanced due to the local nanoforest formation. The conductance modulation property of the SiNWs, which is an important characteristic in sensor and charge transfer based applications, can be largely enhanced.

Hybrid porphyrin-silicon nanowire field-effect transistor by opto-electrical excitation.

A porphyrin-silicon nanowire (Si-NW) hybrid field-effect transistor is introduced. The hybrid device has separate electrical and optical gates surrounding the Si-NW channel. Porphyrin, a component of chlorophyll, is employed as an optical gate to modulate the potential of the Si-NW channel.

A nanoforest structure for practical surface-enhanced Raman scattering substrates.

A nanoforest structure for surface-enhanced Raman scattering (SERS) active substrates is fabricated and analyzed. The detailed morphology of the resulting structure can be easily controlled by modifying the process parameters such as initial gold layer thickness and etching time. The applicability of the nanoforest substrate as a label-free SERS immunosensor is demonstrated using influenza A virus subtype H1N1.