Effects of self-etch adhesive agitation with diode laser on dentin bond strength.

The present study assessed the effect of active application of self-etch adhesives with diode laser irradiation on the shear dentin bond strength. Sixty bovine incisors, each embedded individually in hard plaster blocks, were divided into two groups based on the adhesive system used: Group 1 Adper Easy One and Group 2 Clearfil SE Protect. Based on the application technique of self-etch adhesives, each main group was further divided into three subgroups: passive application, active application with a micro-brush, and active application with a 976-nm diode laser tip (phototherapy active application).

Effects of rotary brush active application on enamel etching patterns of self-etch adhesive systems.

Abstract.

Repair of aged bulk-fill composite with posterior composite: Effect of different surface treatments.

Objective: In the present study, the ability of posterior resin composite to repair aged bulk-fill resin composite and vice versa were assessed by shear bond strength testing.

Materials And Methods: Resin composite substrates were aged and surfaces were abraded with abrasive papers, then bulk-fill substrates were repaired with posterior resin composite and vice versa using different surface treatments (no surface treatment [control]; etching with 37% phosphoric acid [H PO ] for 20 seconds; etching with 10% hydrofluoric acid [HF] for 20 seconds; etching with 37% H PO for 20 seconds + adhesive application; etching with 10% HF for 20 seconds + adhesive application; adhesive application only). Shear bond strengths (SBS) were then measured and surface roughness values (Ra) were determined.

The durability of adhesion to Er,Cr:YSGG laser-irradiated enamel.

Background And Aims: Adhesion durability of resin adhesives with Er,Cr:YSGG laser irradiated-enamel has been rarely investigated in the literature. Thus, the present study evaluated the influence of long-term water storage (12-month) on resin bond strength with the enamel irradiated with Er,Cr:YSGG laser irradiation deployed different settings.

Materials And Methods: The flattened enamel samples of 35 bovine teeth, which were embedded into acrylic blocks, were randomly divided into 7 groups (n = 5), according to surface treatments using Er,Cr:YSGG laser with different parameters 6 W/20 Hz, 6 W/35 Hz, 6 W/50 Hz, 3 W/20 Hz, 3 W/35 Hz, 3 W/50 Hz or no laser treatment (Bur-treating as a control).

Bonding performance of universal adhesives to er,cr:YSGG laser-irradiated enamel.

Universal adhesives have been recently introduced for use as self-etch or etch-and-rinse adhesives depending on the dental substrate and clinical condition. However, their bonding effectiveness to laser-irradiated enamel is still not well-known. Thus, the aim of this study was to compare the shear bond strength (SBS) of universal adhesives (Single Bond Universal; Nova Compo-B Plus) applied to Er,Cr:YSGG laser-irradiated enamel with SBS of the same adhesives applied in self-etch and acid-etching modes, respectively.

Effects of Er,Cr:YSGG laser parameters on dentin bond strength and interface morphology.

Previous studies have shown the effects of Er,Cr:YSGG laser irradiation on the dentin bond strength; but there are few reports that show the significance of the irradiation with different laser parameters on dentin bond strength and interface morphology. This in-vitro study attempted to evaluate the microtensile bond strength (μTBS) and interface morphology of resin-dentin interfaces, either followed by treatment with Er,Cr:YSGG laser irradiation with different parameters or not. The flattened dentin samples of 35 bovine teeth were embedded into acrylic blocks and randomly divided into seven groups according to surface treatments using Er,Cr:YSGG lasers with different parameters: 3 W/20 Hz, 3 W/35 Hz, 3 W/50 Hz, 1.

Influence of different Er,Cr:YSGG laser parameters on long-term dentin bond strength of self-etch adhesive.

The aim of the present study was to evaluate the effects of erbium, chromium: yattrium-scandium-gallium-garnet (Er,Cr:YSGG) laser frequency on microtensile bond strength (μTBS) of a self-etch adhesive to dentin after 15-month water storage. The Er,Cr:YSGG laser can safely be used on dental hard tissue. However, no study has compared the effects of Er,Cr:YSGG laser parameters and aging by water storage on the bonding effectiveness of self-etch adhesives to dentin.

Bond durability of contemporary adhesive systems to pulp chamber dentin.

: The purpose of this study was to evaluate long-term bond strengths of dentin adhesive systems, which include one-step self-etch adhesive systems (Optibond All-in-one, Kerr; Adper Prompt L-POP, 3 M ESPE), a three-step etch-and-rinse adhesive (Optibond FL, Kerr) and two-step self-etch adhesive (AdheSE Bond, Ivoclar), applied to pulp chamber dentin surfaces after 12-month water storage by using microtensile bond strength (µTBS) test. : Dentin adhesive systems were applied to unprepared pulp chamber dentin surfaces according to manufacturer's directions, respectively ( = 5). After applying adhesive systems, composite buildups were done incrementally.

Effect of simplified ethanol-wet bonding on dentin bonding durability of etchand-rinse adhesives.

This in vitro study evaluated the effects of simplified ethanol-wet bonding technique on dentin bonding durability of two etchand-rinse adhesives to bovine dentin. Sixteen freshly extracted bovine incisors were divided into four groups according to bonding technique (water-wet or ethanol-wet bonding) and adhesive (Single Bond 2 or Prime & Bond NT). After etching and rinsing, dentin surfaces were left either water-moist or immersed in ethanol.

Letter to the Editor regarding "Depletion of water molecules during ethanol wet-bonding with etch and rinse dental adhesives".

I would like to comment on the above titled paper that recently published in Materials Science and Engineering C 33:21-27 (2013). I mentioned potential deficiencies in the study design. Then, I argued some statements made in the paper about interactions between bounded water around collagen molecules and resin infiltration, hence longevity of resin bonding.