Mechanism of Pressure-Sensitive Adhesion in Nematic Elastomers.

Nematic liquid crystal elastomers (LCEs) have anomalously high vibration damping, and it has been assumed that this is the cause of their anomalously high-pressure-sensitive adhesion (PSA). Here, we investigate the mechanism behind this enhanced PSA by first preparing thin adhesive tapes with LCE of varying cross-linking densities, characterizing their material and surface properties, and then studying the adhesion characteristics with a standard set of 90° peel, lap shear, and probe tack tests. The study confirms that the enhanced PSA is only present in (and due to) the nematic phase of the elastomer, and the strength of bonding takes over 24 h to fully reach its maximum value.

Momentum transfer on impact damping by liquid crystalline elastomers.

The effect of elastomeric damping pads, softening the collision of hard objects, is investigated comparing the reference silicone elastomer and the polydomain nematic liquid crystalline elastomer, which has a far superior internal dissipation mechanism. We specifically focus not just on the energy dissipation, but also on the momentum conservation and transfer during the collision, because the latter determines the force exerted on the target and/or the impactor-and it is the force that does the damage during the short time of an impact, while the energy might be dissipated on a much longer time scale. To better assess the momentum transfer, we compare the collision with a very heavy object and the collision with a comparable mass, when some of the impact momentum is retained in the target receding away from the collision.

Rheology of vitrimers.

We describe the full rheology profile of vitrimers, from small deformation (linear) to large deformation (non-linear) viscoelastic behaviour, providing concise analytical expressions to assist the experimental data analysis, and also clarify the emerging insights and rheological concepts in the subject. We identify the elastic-plastic transition at a time scale comparable to the life-time of the exchangeable bonds in the vitrimer network, and propose a new method to deduce material parameters using the Master Curves. At large plastic creep, we describe the strain thinning when the material is subjected to a constant stress or force, and suggest another method to characterize the material parameters from the creep curves.

Programmable Shape Change in Semicrystalline Liquid Crystal Elastomers.

Liquid crystal elastomers (LCEs) are stimuli-responsive materials capable of reversible and programmable shape change in response to an environmental stimulus. Despite the highly responsive nature of these materials, the modest elastic modulus and blocking stress exhibited by these actuating materials can be limiting in some engineering applications. Here, we engineer a semicrystalline LCE, where the incorporation of semicrystallinity in a lightly cross-linked liquid crystalline network yields tough and highly responsive materials.

Thiol-acrylate side-chain liquid crystal elastomers.

The Michael addition 'click' chemistry was used to graft acrylate-terminated mesogenic groups onto the polysiloxane backbone polymer chain with thiol functional groups, with a constant 15% fraction of diacrylate reacting monomers as crosslinkers. Three different types of mesogens were used, and also their 50 : 50 mixtures, and in all cases we have obtained the smectic-A phase of the resulting liquid crystalline elastomer. Using X-ray diffraction, calorimetry and dynamic mechanical analysis, we investigated the relationship between the molecular structure of mesogenic side groups and the structure and properties of the elastomers.

Impact damping and vibration attenuation in nematic liquid crystal elastomers.

Nematic liquid crystal elastomers (LCE) exhibit unique mechanical properties, placing them in a category distinct from other viscoelastic systems. One of their most celebrated properties is the 'soft elasticity', leading to a wide plateau of low, nearly-constant stress upon stretching, a characteristically slow stress relaxation, enhanced surface adhesion, and other remarkable effects. The dynamic soft response of LCE to shear deformations leads to the extremely large loss behaviour with the loss factor tanδ approaching unity over a wide temperature and frequency ranges, with clear implications for damping applications.

Dynamic Semicrystalline Networks of Polypropylene with Thiol-Anhydride Exchangeable Crosslinks.

Thermoplastic polyolefins (TPOs) crosslinked by dynamic covalent bonds (TPOs) have the potential to be the most utilized class of polymer in the world, with applications ranging from household and automotive to biomedical devices and additive manufacturing. TPO combines the benefits of thermoplastics and thermosets in a "single material" and potentially avoids their shortcomings. Here, we describe a new two-stage reaction extrusion strategy of TPOs with a backbone consisting of inert C-C bonds (polypropylene, PP), and thiol-anhydride, to dynamically crosslink PP through thiol-thioester bond exchange.

A Copolymer-in-Oil Tissue-Mimicking Material With Tuneable Acoustic and Optical Characteristics for Photoacoustic Imaging Phantoms.

Photoacoustic imaging (PAI) standardisation demands a stable, highly reproducible physical phantom to enable routine quality control and robust performance evaluation. To address this need, we have optimised a low-cost copolymer-in-oil tissue-mimickingmaterial formulation. The base material consists of mineral oil, copolymer and stabiliser with defined Chemical Abstract Service numbers.

Continuous spinning aligned liquid crystal elastomer fibers with a 3D printer setup.

Fibrous liquid crystalline elastomers (LCE) are an attractive variant of LCE-based actuators due to their small thickness, leading to faster response times to stimuli, as well as the increased mechanical strength. Fabrication of LCE fibers has been attempted by various research groups using electro-spinning or micro-fluidic techniques, without much success. Here we propose an alternative way to achieve single-step continuous spinning LCE fibers in a more scalable and robust way, based on a liquid-ink 3D printer.

Exchangeable Liquid Crystalline Elastomers and Their Applications.

This Review presents and discusses the current state of the art in "exchangeable liquid crystalline elastomers", that is, LCE materials utilizing dynamically cross-linked networks capable of reprocessing, reprogramming, and recycling. The focus here is on the chemistry and the specific reaction mechanisms that enable the dynamic bond exchange, of which there is a variety. We compare and contrast these different chemical mechanisms and the key properties of their resulting elastomers.

Internal constraints and arrested relaxation in main-chain nematic elastomers.

Nematic liquid crystal elastomers (N-LCE) exhibit intriguing mechanical properties, such as reversible actuation and soft elasticity, which manifests as a wide plateau of low nearly-constant stress upon stretching. N-LCE also have a characteristically slow stress relaxation, which sometimes prevents their shape recovery. To understand how the inherent nematic order retards and arrests the equilibration, here we examine hysteretic stress-strain characteristics in a series of specifically designed main-chain N-LCE, investigating both macroscopic mechanical properties and the microscopic nematic director distribution under applied strains.

The effect of alignment on the rate-dependent behavior of a main-chain liquid crystal elastomer.

This study investigated the effect of alignment on the rate-dependent behavior of a main-chain liquid crystal elastomer (LCE). Polydomain nematic LCE networks were synthesized from a thiol-acrylate Michael addition reaction in the isotropic state. The polydomain networks were stretched to different strain levels to induce alignment then crosslinked in a second stage photopolymerization process.

Light-Driven Dynamic Adhesion on Photosensitized Nematic Liquid Crystalline Elastomers.

In liquid crystal elastomers (LCEs), the internal mechanical loss increases around the nematic-isotropic phase transition and remains high all through the nematic phase, originating from the internal orientational relaxation related to the so-called "soft elasticity". Because the viscoelastic dissipation of the materials affects their adhesion properties, the nematic-isotropic phase transition can cause dramatic changes in the adhesion strength. Although the phase transitions can generally be induced by heat, here, we demonstrate the light-driven transition in dynamic adhesion in dye-doped nematic LCE.

Rates of transesterification in epoxy-thiol vitrimers.

Vitrimers, an important subset of dynamically crosslinked polymer networks, have many technological applications for their excellent properties, and the ability to be re-processed through plastic flow above the so-called vitrification temperature. We report a simple and efficient method of generating such adaptive crosslinked networks relying on transesterification for their bond exchange by utilising the 'click' chemistry of epoxy and thiols, which also has the advantage of a low glass transition temperature. We vary the chemical structure of thiol spacers to probe the effects of concentration and the local environment of ester groups on the macroscopic elastic-plastic transition.

Catalytic Control of Plastic Flow in Siloxane-Based Liquid Crystalline Elastomer Networks.

Liquid crystalline elastomer networks cross-linked by dynamic covalent bonds (xLCE) have the ability to be (re)processed during the plastic flow. However, the current bond-exchange strategies that are used to induce plastic flow in xLCE lack the efficient method to control the elastic-plastic transition. Here we describe a straightforward method to manipulate the transition to plastic flow via the choice of catalyst in xLCE cross-linked by siloxane.

Siloxane crosslinks with dynamic bond exchange enable shape programming in liquid-crystalline elastomers.

Liquid crystalline elastomers (LCE) undergo reversible shape changes in response to stimuli, which enables a wide range of smart applications, in soft robotics, adhesive systems or biomedical medical devices. In this study, we introduce a new dynamic covalent chemistry based on siloxane equilibrium exchange into the LCE to enable processing (director alignment, remolding, and welding). Unlike the traditional siloxane based LCE, which were produced by reaction schemes with irreversible bonds (e.

Enhanced Dynamic Adhesion in Nematic Liquid Crystal Elastomers.

Smart adhesives that undergo reversible detachment in response to external stimuli enable a wide range of applications in household products, medical devices, or manufacturing. Here, a new model system for the design of smart soft adhesives that dynamically respond to their environment is presented. By exploiting the effect of dynamic soft elasticity in nematic liquid crystal elastomers (LCE), the temperature-dependent control of adhesion to a solid glass surface is demonstrated.

Responsive, 3D Electronics Enabled by Liquid Crystal Elastomer Substrates.

Traditional electronic devices are rigid, planar, and mechanically static. The combination of traditional electronic materials and responsive polymer substrates is of significant interest to provide opportunities to replace conventional electronic devices with stretchable, 3D, and responsive electronics. Liquid crystal elastomers (LCEs) are well suited to function as such dynamic substrates because of their large strain, reversible stimulus response that can be controlled through directed self-assembly of molecular order.

High strain actuation liquid crystal elastomers via modulation of mesophase structure.

Control of the mesophase in liquid crystalline elastomers (LCEs) is a critical aspect in harnessing their unique stimuli-responsive properties. Few studies have compared nematic and smectic main-chain LCEs in a direct way. Traditionally, it is believed that the mesogen core and synthetic route determines the phase behavior.

Synthesis of Programmable Main-chain Liquid-crystalline Elastomers Using a Two-stage Thiol-acrylate Reaction.

This study presents a novel two-stage thiol-acrylate Michael addition-photopolymerization (TAMAP) reaction to prepare main-chain liquid-crystalline elastomers (LCEs) with facile control over network structure and programming of an aligned monodomain. Tailored LCE networks were synthesized using routine mixing of commercially available starting materials and pouring monomer solutions into molds to cure. An initial polydomain LCE network is formed via a self-limiting thiol-acrylate Michael-addition reaction.