Influence of Ultra-Thin Ge₃N₄ Passivation Layer on Structural, Interfacial, and Electrical Properties of HfO₂/Ge Metal-Oxide-Semiconductor Devices.

We report the effects of the nitride passivation layer on the structural, electrical, and interfacial properties of Ge metal-oxide-semiconductor (MOS) devices with a hafnium oxide (HfO₂) gate dielectric layer deposited on -type 〈100〉 Ge substrates. X-ray photoelectron spectroscopy analysis confirmed the chemical states and formation of HfO₂/Ge₃N₄ on Ge. The interfacial quality and thickness of the layers grown on Ge were confirmed by high-resolution transmission electron microscopy.

Analysis of Laser Injection Condition and Electrical Properties in Local BSF for Laser Fired Contact c-Si Solar Cell Applications.

A crystalline silicon (c-Si) local-back-contact (LBC) solar cell for which a laser-condition-optimized surface-recombination velocity (SRV), a contact resistance (Rc), and local back surface fields (LBSFs) were utilized is reported. The effect of the laser condition on the rear-side electrical properties of the laser-fired LBC solar cell was studied. The Nd:YAG-laser (1064-nm wavelength) power and frequency were varied to obtain LBSF values with a lower contact resistance.

Enhanced Haze Ratio on Glass by Novel Vapor Texturing Method.

State-of-the-art optical trapping designs are required to enhance the light trapping capabilities of tandem thin film silicon solar cells. The wet etch process is used to texture the glass surface by dipping in diluted acidic solutions such as HNO3 (nitric acid) and HF (hydrofluoric acid). For vapor texturing, the vapor was generated by adding silicon to HF:HNO3 acidic solution.

Method for Fabricating Textured High-Haze ZnO:Al Transparent Conduction Oxide Films on Chemically Etched Glass Substrates.

We developed a technique for forming textured aluminum-doped zinc oxide (ZnO:Al) transparent conductive oxide (TCO) films on glass substrates, which were etched using a mixture of hydrofluoric (HF) and hydrochloric (HCl) acids. The etching depth and surface roughness increased with an increase in the HF content and the etching time. The HF-based residues produced insoluble hexafluorosilicate anion- and oxide impurity-based semipermeable films, which reduced the etching rate.

Boron Oxygen Pair Effect in p+ Emitter and Nanosized Boron Rich Layer by Fold Coordination Analysis for Crystalline Silicon Solar Cell Applications.

N-type substrates possess better material characteristics than p-type substrates for high efficiency mass producible Si solar cells with HIT, IBC structures. The major drawbacks of these structures are a complicated fabrication process and an expensive unit cost. In this paper, the boron emitter doping profile of a nanosized boron rich layer (BRL), for which the boron and oxygen concentrations are correlated, is optimized to fabricate high efficiency solar cells on an n-type substrate.

Effects of Low Temperature Anneal on the Interface Properties of Thermal Silicon Oxide for Silicon Surface Passivation.

High quality surface passivation has gained a significant importance in photovoltaic industry for reducing the surface recombination and hence fabricating low cost and high efficiency solar cells using thinner wafers. The formation of good-quality SiO2 films and SiO2/Si interfaces at low processing temperatures is a prerequisite for improving the conversion efficiency of industrial solar cells with better passivation. High-temperature annealing in inert ambient is promising to improve the SiO2/Si interface.

Advanced Passivation Technology and Loss Factor Minimization for High Efficiency Solar Cells.

High-efficiency Si solar cells have attracted great attention from researchers, scientists, photovoltaic (PV) industry engineers for the past few decades. With thin wafers, surface passivation becomes necessary to increase the solar cells efficiency by overcoming several induced effects due to associated crystal defects and impurities of c-Si. This paper discusses suitable passivation schemes and optimization techniques to achieve high efficiency at low cost.

Characteristics of Carrier Collection of Nanopillar-Patterned Silicon Solar Cells.

Nanopillar-patterned Si solar cells were investigated. Ag nanoparticles were coated on a polished Si substrate as an etching mask. Reactive ion etching caused Si nanopillars to replicate in a reverse fashion on the Ag nanoparticles over a large area.

Low Surface Recombination Velocity on P-Type Cz-Si Surface by Sol-Gel Deposition of Al2O3 Films for Solar Cell Applications.

High quality surface passivation has gained a significant importance in photovoltaic industry for fabricating low cost and high efficiency solar cells using thinner and lower cost wafers. The passivation property of spin coated Al2O3 films with a thickness of about 50 nm on p-type Cz-Si wafers has been investigated as a function of annealing temperatures. An effective surface recombination velocity of 55 cm/s was obtained for the films annealed at 500 °C.

Analysis of Resistance and Surface Recombination Velocities by Contact Coverage for Optimizing Electrical Loss in c-Si Local Back Contact.

Recently, the importance of solar cell research has emerged due to emerging social issues such as environmental pollution problems and rising oil prices. Accordingly, each company is studying to make solar cell of high efficiency. In order to fabricate high-efficiency solar cells, the two major techniques have to be applied on the rear.

Direct metallization local Al-back surface field for high efficiency screen printed crystalline silicon solar cells.

In this paper, we present a detailed study on the local back contact (LBC) formation of rear-surface-passivated silicon solar cells, where both the LBC opening and metallization are realized by one-step alloying of a dot of fine pattern screen-printed aluminum paste with the silicon substrate. Based on energy dispersive spectrometer (EDS) and scanning electron microscopy (SEM) characterizations, we suggest that the aluminum distribution and the silicon concentration determine the local-back-surface-field (Al-p+) layer thickness, resistivity of the Al-p+ and hence the quality of the Al-p+ formation. The highest penetration of silicon concentration of 78.

Surface-concentrated light and efficient carrier collection in microhole-patterned Si solar cells.

We investigate photovoltaic characteristics of crystalline Si solar cells with microhole-patterned surface. We compare patterned samples with different hole-widths and periods with a planar counterpart. From the finite-difference time-domain simulation, the patterned and planar samples are expected to have similar short circuit current density, J(sc) (difference: 1.

Selective emitter using a screen printed etch barrier in crystalline silicon solar cell.

The low level doping of a selective emitter by etch back is an easy and low cost process to obtain a better blue response from a solar cell. This work suggests that the contact resistance of the selective emitter can be controlled by wet etching with the commercial acid barrier paste that is commonly applied in screen printing. Wet etching conditions such as acid barrier curing time, etchant concentration, and etching time have been optimized for the process, which is controllable as well as fast.

A novel method for crystalline silicon solar cells with low contact resistance and antireflection coating by an oxidized Mg layer.

One of the key issues in the solar industry is lowering dopant concentration of emitter for high-efficiency crystalline solar cells. However, it is well known that a low surface concentration of dopants results in poor contact formation between the front Ag electrode and the n-layer of Si. In this paper, an evaporated Mg layer is used to reduce series resistance of c-Si solar cells.