Experimental Study on the Chlorine-Induced Corrosion and Blister Formation of Steel Pipes Coated with Modified Polyethylene Powder.

In this study, chlorine-induced corrosion and blister formation on steel pipes (SPs) coated with modified polyethylene powder (MPP) were evaluated through various tests, including chlorine exposure, wet immersion, and temperature gradient experiments. The results confirmed that the extent of corrosion and iron leaching varied with the coating type as expected. In batch leaching tests, no corrosion was observed on modified polyethylene-coated steel pipes (MPCSPs) within a chlorine concentration range of 0 mg/L to 10 mg/L; similarly, there were no significant changes in specimen weight or iron levels.

Effects of Macro Fibers on Crack Opening Reduction in Fiber Reinforced Concrete Overlays.

Macro fibers have been extensively used in the construction of various concrete structures, including bridges, dams, tunnels, industrial floors, and pavements. However, their effectiveness in reducing crack opening widths in concrete pavements has not been fully explored. This study aims to delineate the role of fibers by identifying the optimal types and volumes for effectively controlling cracks in concrete pavement structures, particularly in thin overlays.

Interfacial Bond Properties of Underwater Concrete Coated with Bisphenol A Epoxy Resins.

This study investigated changes in the interfacial properties of epoxy-coated concrete exposed to various conditions, regarding the epoxy type, coating equipment, and exposure environment and period. The measured coating thickness and pull-off bond strength exhibited diverse trends, depending on the exposure period and conditions. In the real sea (RS) environment, the average bond strengths for bisphenol A (BPA) (E1), BPA with zinc powder (E2), and BPA with cresyl glycidyl ether (E3) were 1.

Influence of Polyethylene Terephthalate Powder on Hydration of Portland Cement.

The management of plastic waste is a massive challenge and the recycling of plastics for newer applications is a potential solution. This study investigates the feasibility of using polyethylene terephthalate (PET) powder in cementitious composites. The changes in the strength and microstructure of Portland cement incorporating PET powder with different replacement ratios were systematically analyzed through the measurements of compressive strength, isothermal calorimetry, X-ray diffraction, thermogravimetric analysis, and Raman spectroscopy.

Exploring Structural Evolution of Portland Cement Blended with Supplementary Cementitious Materials in Seawater.

The present study investigated the structural evolution of Portland cement (PC) incorporating supplementary cementitious materials (SCMs) exposed to seawater. The samples were made with replacing Portland cement with 10 mass-% silica fume, metakaolin or glass powder. The reaction degree of SCMs estimated by the portlandite consumption shows that metakaolin has the highest reaction degree, thus metakaolin-blended PC exhibits the highest strength.

Pullout Behavior of Recycled Waste Fishing Net Fibers Embedded in Cement Mortar.

In this study, recycled waste fishing net (WFN) short fibers were proposed to be used as short fiber reinforcements. The pullout resistance of WFN short fibers embedded in cement mortar was investigated by conducting fiber pullout tests. Three types of WFN short fibers and two types of commercial polypropylene (CP) fibers were investigated.

Effects of Water Exposure on the Interfacial Bond between an Epoxy Resin Coating and a Concrete Substrate.

Interfacial bond properties of six different epoxy resins used to coat submerged concrete structures were investigated. Test variables included coating type, coating equipment, and underwater curing time. Coating thickness and pull-off bond strength were measured using commercially available test equipment.

Humidity-resistant triboelectric energy harvester using electrospun PVDF/PU nanofibers for flexibility and air permeability.

We present a triboelectric energy harvester fabricated with a simple electrospinning process of polyvinylidene fluoride/polyurethane polymers on conductive fabric. This electrospinning process provides higher electrical power output and hydrophobicity driven humidity resistance compared to flat polymer energy harvesters. By using conductive fabric as collector and electrode, the device could retain air permeability and flexibility.

Multidirectional flexible force sensors based on confined, self-adjusting carbon nanotube arrays.

We demonstrate a highly sensitive force sensor based on self-adjusting carbon nanotube (CNT) arrays. Aligned CNT arrays are directly synthesized on silicon microstructures by a space-confined growth technique which enables a facile self-adjusting contact. To afford flexibility and softness, the patterned microstructures with the integrated CNTs are embedded in polydimethylsiloxane structures.

Low-Temperature Selective Growth of Tungsten Oxide Nanowires by Controlled Nanoscale Stress Induction.

We report a unique approach for the patterned growth of single-crystalline tungsten oxide (WOx) nanowires based on localized stress-induction. Ions implanted into the desired growth area of WOx thin films lead to a local increase in the compressive stress, leading to the growth of nanowire at lower temperatures (600 °C vs. 750-900 °C) than for equivalent non-implanted samples.

Reversible and continuous latching using a carbon internanotube interface.

Mechanical multistability is greatly beneficial in microelectromechanical systems because it offers multiple stable positioning of movable microstructures without a continuous energy supply. Although mechanical latching components based on multistability have been widely used in microsystems, their latching positions are inherently discrete and the number of stable positions is quite limited because of the lithographical minimum feature size limit of microstructures. We report a novel use of aligned carbon nanotube (CNT) arrays as latching elements in a movable micromechanical device.