Direct Electrochemical Synthesis of Metal-Organic Frameworks: Cu (BTC) and Cu(TCPP) on Copper Thin films and Copper-Based Microstructures.

Cu thin films and Cu O microstructures were partially converted to the Metal-Organic Frameworks (MOFs) Cu (BTC) or Cu(TCPP) using an electrochemical process with a higher control and at milder conditions compared to the traditional solvothermal MOF synthesis. Initially, either a Cu thin film was sputtered, or different kinds of Cu or Cu O microstructures were electrochemically deposited onto a conductive ITO glass substrate. Then, these Cu thin films or Cu-based microstructures were subsequently coated with a thin layer of either Cu (BTC) or Cu(TCPP) by controlled anodic dissolution of the Cu-based substrate at room temperature and in the presence of the desired organic linker molecules: 1,3,5-benzenetricarboxylic acid (BTC) or photoactive 4,4',4'',4'''-(Porphine-5,10,15,20-tetrayl) tetrakis(benzoic acid) (TCPP) in the electrolyte.

Multimethod Approach to the Low-Overpotential Region of Micro- to Macro-Scale Working Electrodes of Sub-10 nm Gold Nanoparticles in the CO Reduction Reaction.

The electrochemical carbon dioxide reduction reaction (CO2RR) over carbon-supported gold nanoparticles (AuNP) was investigated using a broad variety of (electro)analytical methods, including linear sweep voltammetry with a rotating disk electrode (LSV-RDE), sample-generation tip-collection mode of scanning electrochemical microscopy (SG/TC-SECM), as well as full cell tests with highly sensitive online gas chromatography (GC). In contrast to most other studies, this work focuses on the low-overpotential region (0 to -0.4 V vs RHE) where initial product formation is already detected and addresses micro- to macro-sized electrodes.

Characterization of sulfur/carbon copolymer cathodes for Li-S batteries: a combined experimental and Raman spectroscopy study.

Optimization of lithium-sulfur batteries highly depends on exploring and characterizing new cathode materials. Sulfur/carbon copolymers have recently attracted much attention as an alternative class of cathodes to replace crystalline sulfur. In particular, poly(sulfur--1,3-diisopropenylbenzene) (S/DIB) has been under considerable experimental and theoretical investigations, promising a good performance in mitigating the so-called shuttle effect.

Quantifying the removal of stabilizing thiolates from gold nanoparticles on different carbon supports and the effect on their electrochemical properties.

Gold nanoparticles <10 nm in size are typically prepared using stabilizing agents, thiolates. Often standard recipes from literature are used to presumably remove these stabilisers to liberate the surface, for catalytic or electrocatalytic applications, however the success of these procedures is often not verified. In this work, thiolate-stabilised AuNPs of 2 nm in size were synthesized and supported onto three different carbon supports, resulting in loadings from 15 to 25 wt% Au.

Hierarchically structured 3D carbon nanotube electrodes for electrocatalytic applications.

Hierarchically structured 3-dimensional electrodes based on branched carbon nanotubes (CNTs) are prepared on a glassy carbon (GC) substrate in a sequence of electrodeposition and chemical vapor deposition (CVD) steps as follows: Primary CNTs are grown over electrodeposited iron by CVD followed by a second Fe deposition and finally the CVD growth of secondary CNTs. The prepared 3-dimensional CNT structures (CNT/CNT/GC) exhibit enhanced double-layer capacitance and thus larger surface area compared to CNT/GC. Pt electrodeposition onto both types of electrodes yields a uniform and homogeneous Pt nanoparticle distribution.

In Situ Characterization of Ni and Ni/Fe Thin Film Electrodes for Oxygen Evolution in Alkaline Media by a Raman-Coupled Scanning Electrochemical Microscope Setup.

We present a spectroelectrochemical setup, in which Raman microscopy is combined with scanning electrochemical microscopy (SECM) in order to provide both spectroscopic and electrochemical information on the very same location of an electrode at the same time. The setup is applied to a subject of high academic and practical interest, namely, the oxygen evolution reaction at Ni and Ni/Fe electrodes. It comprises a transparent substrate electrode, onto which Ni and Ni/Fe thin films are deposited.

Carbon-Supported Copper Nanomaterials: Recyclable Catalysts for Huisgen [3+2] Cycloaddition Reactions.

Highly disperse copper nanoparticles immobilized on carbon nanomaterials (CNMs; graphene/carbon nanotubes) were prepared and used as a recyclable and reusable catalyst to achieve Cu(I) -catalyzed [3+2] cycloaddition click chemistry. Carbon nanomaterials with immobilized N-heterocyclic carbene (NHC)-Cu complexes prepared from an imidazolium-based carbene and Cu(I) show excellent stability including high efficiency at low catalyst loading. The catalytic performance evaluated in solution and in bulk shows that both types of Cu-CNMs can function as an effective recyclable catalysts (more than 10 cycles) for click reactions without decomposition and the use of external additives.

Synthesis of Cu(core) Pt(shell) nanoparticles as model structures for core-shell electrocatalysts by direct platinum electrodeposition on copper.

The synthesis of Cu(core)Pt(shell) model catalysts by the direct electrochemical deposition of Pt on Cu particles is presented. Cu particles with an average diameter of 200 nm have been deposited on glassy-carbon electrodes by double pulse electrodeposition from a copper sulfate solution. Subsequent deposition from a platinum nitrate solution under potential control allows for a high selectivity of the Pt deposition towards Cu.

Visualization of chlorine evolution at dimensionally stable anodes by means of scanning electrochemical microscopy.

Scanning electrochemical microscopy (SECM) has been used to detect and visualize the local electrocatalytic activity of dimensionally stable anodes (DSA) for Cl(2) evolution from brine. The sample generation-tip collection (SG-TC) mode of SECM shows limitations arising from complications connected with the reduction of Cl(2) at the SECM tip due to the presence of a significant amount of nondissolved Cl(2) gas. Because only dissolved Cl(2) can be electrochemically reduced at the tip, a large amount of the Cl(2) gas which is produced at active spots of the DSA is not detected.

A spectroscopic proton-exchange membrane fuel cell test setup allowing fluorescence x-ray absorption spectroscopy measurements during state-of-the-art cell tests.

A test setup for membrane-electrode-assemblies (MEAs) of proton exchange membrane fuel cells which allows in situ fluorescence x-ray absorption spectroscopy studies of one electrode with safe exclusion of contributions from the counter electrode is described. Interference by the counter electrode is excluded by a geometry including a small angle of incidence (< 6°) between primary beam and electrode layer. The cell has been constructed by introducing just minor modifications to an electrochemical state-of-the-art MEA test setup, which ensures realistic electrochemical test conditions.

Metal-free and electrocatalytically active nitrogen-doped carbon nanotubes synthesized by coating with polyaniline.

Nitrogen doping of multi-walled carbon nanotubes (CNTs) was achieved by the carbonization of a polyaniline (PANI) coating. First, the CNTs were partially oxidized with KMnO4 to obtain oxygen-containing functional groups. Depending on the KMnO4 loading, thin layers of birnessite-type MnO2 (10 wt% and 30 wt%) were obtained by subsequent thermal decomposition.

Electrochemical synthesis of core-shell catalysts for electrocatalytic applications.

A novel electrochemical method to prepare platinum shells around carbon-supported metal nanoparticles (Ru and Au) by pulsed electrodeposition from solutions containing Pt ions is presented. Shell formation is confirmed by characteristic changes in the cyclic voltammograms, and is further evidenced by monitoring particle growth by transmission electron microscopy as well as by energy-dispersive analysis of X rays (EDX). Scanning electrochemical microscopy and EDX measurements indicate a selective Pt deposition on the metal/carbon catalyst, but not on the glassy carbon substrate.

Pt-Ag catalysts as cathode material for oxygen-depolarized electrodes in hydrochloric acid electrolysis.

Pt-Ag nanoparticles were prepared on a glassy carbon (GC) surface by pulsed electrodeposition and tested using cyclic voltammetry and scanning electrochemical microscopy (SECM) with respect to their possible use as catalyst material for oxygen reduction in 400 mM HCl solution. For comparison, a Pt catalyst was investigated under similar conditions. The redox competition mode of scanning electrochemical microscopy (RC-SECM) was adapted to the specific conditions caused by the presence of Cl(-) ions and used to visualize the local catalytic activity of the Pt-Ag deposits.

Visualization of the local catalytic activity of electrodeposited Pt-Ag catalysts for oxygen reduction by means of SECM.

Pt-Ag nanoparticle co-deposits with different Pt-Ag ratios were prepared on a glassy carbon (GC) surface by pulsed electrodeposition and investigated for their catalytic activity in electrocatalytic oxygen reduction by using cyclic voltammetry (CV), rotating disc electrode (RDE) and scanning electrochemical microscopy (SECM) in 0.1 M phosphate buffer (pH 7.0).

Effect of reduction temperature on the preparation and characterization of Pt-Ru nanoparticles on multiwalled carbon nanotubes.

Carbon nanotubes (CNT) supported platinum-ruthenium (Pt-Ru) catalysts were prepared by impregnation-reduction using an ethanolic solution of H2PtCl6 and RuCl3. The effect of reduction temperatures on particle size, surface area and their relationship to the electrocatalytic activity for methanol oxidation were investigated. Thermogravimetric analysis, scanning electron microscopy, transmission electron microscopy, X-ray diffraction (XRD) as well as X-ray photoelectron spectroscopy (XPS) were used for the catalyst characterization.

Electrocatalytic activity of spots of electrodeposited noble-metal catalysts on carbon nanotubes modified glassy carbon.

A strategy for the screening of the electrocatalytic activity of electrocatalysts for possible application in fuel cells and other devices is presented. In this approach, metal nanoclusters (Pt, Au, Ru, and Rh and their codeposits) were prepared using a capillary-based droplet-cell by pulsed electrodeposition in a diffusion-restricted viscous solution. A glassy carbon surface was modified with carbon nanotubes (CNTs) by electrophoretic accumulation and was used as substrate for metal nanoparticle deposition.

Controlled synthesis of gold nanostructures by a thermal approach.

Shape-controlled gold nanostructures were successfully synthesized in an aqueous solution by a one-step, non-templated thermal reduction method through heating of a poly(vinylpyrrolidone)/HAuCl4 aqueous solution. Poly(vinylpyrrolidone) (PVP) serves as both the stabilizing surfactant and reducing agent for the controlled synthesis of gold nanostructures with different shapes. Upon adjusting the chain-length and the concentration of the PVP, decahedral, icosahedral and platelike gold nanostructures with dominating distribution were fabricated, respectively, with the ratio of terminating OH groups at the polymer to Au ions as an important experimental parameter.

Silver as acrolein hydrogenation catalyst: intricate effects of catalyst nature and reactant partial pressures.

The hydrogenation of acrolein over pure and supported silver has been investigated with a focus on the influence of catalyst structure and reaction pressure (mbar to 20 bar range) on activity and selectivity. An onset of formation of allyl alcohol beyond 100 mbar reaction pressure (at 250 degrees C) is ascribed to a change in adsorption geometry upon increasing coverage. Smaller silver particles (in the nanometer range), the proximity of a reducible oxide component as well as high pressure lead to enhanced allyl alcohol formation; the selectivity to the other main product propionaldehyde is reduced.