High-Hole-Mobility Fiber Organic Electrochemical Transistors for Next-Generation Adaptive Neuromorphic Bio-Hybrid Technologies.

The latest developments in fiber design and materials science are paving the way for fibers to evolve from parts in passive components to functional parts in active fabrics. Designing conformable, organic electrochemical transistor (OECT) structures using poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) fibers has excellent potential for low-cost wearable bioelectronics, bio-hybrid devices, and adaptive neuromorphic technologies. However, to achieve high-performance, stable devices from PEDOT:PSS fibers, approaches are required to form electrodes on fibers with small diameters and poor wettability, that leads to irregular coatings.

Utilization of Lignin-Derived Small Molecules: Epoxy Polymers from Lignin Oxidation Products.

Much effort has been invested in developing methods for producing small molecules from lignin as a way to source feedstock chemicals from renewable sources. Significant progress is being made, and methods for deconstructing lignin are producing good yields of small, mononuclear aromatic products-sufficient amounts to enable studies of the potential use of these compounds as replacements for compounds currently produced from petroleum. To investigate the use of lignin products in epoxies, we begin with aromatic acids that can be produced from lignin, treat them with epichlorohydrin to make glycidyl ethers, and investigate the thermal and mechanical properties of cured mixtures of these compounds with a commercial epoxy resin (EPON 826) and an anhydride curing agent (NMA).

Tailoring the Seebeck Coefficient of Spray-Coated Poly(3,4-ethylenedioxythiophene): Poly(styrenesulfonate) Films with Nitrogen Doped Multiwalled Carbon Nanotubes.

The thermoelectric properties of flexible thin films fabricated from two commercial poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) formulations filled with multiwalled carbon nanotubes (MWCNT) and nitrogen-doped MWCNT (N-MWCNT) were investigated. A simple spray-coating method for the fabrication of such flexible films on a polyethylene terephthalate substrate was developed. While increasing the MWCNT concentration had little effect on the thermoelectric properties, increasing the N-MWCNT concentration resulted in the emergence of an overall -type semiconducting behavior and, thereby, tailoring the Seebeck coefficient of the composite films from -type to -type was shown.

All-Organic Textile Thermoelectrics with Carbon-Nanotube-Coated n-Type Yarns.

Thermoelectric textiles that are able to generate electricity from heat gradients may find use as power sources for a wide range of miniature wearable electronics. To realize such thermoelectric textiles, both p- and n-type yarns are needed. The realization of air-stable and flexible n-type yarns, i.

Spray-Coated Multiwalled Carbon Nanotube Composite Electrodes for Thermal Energy Scavenging Electrochemical Cells.

Spray-coated multiwalled carbon nanotube/poly(vinylidene fluoride) (MWCNT/PVDF) composite electrodes, scCNTs, with varying CNT compositions (2 to 70 wt %) are presented for use in a simple thermal energy-scavenging cell (thermocell) based on the ferro/ferricyanide redox couple. Their utility for direct thermal-to-electrical energy conversion is explored at various temperature differentials and cell orientations. Performance is compared to that of buckypaper, a 100% CNT sheet material used as a benchmark electrode in thermocell research.

Photoinduced p- to n-type Switching in Thermoelectric Polymer-Carbon Nanotube Composites.

UV-induced switching from p- to n-type character is demonstrated during deposition of carbon-nanotube-conjugated polymer composites. This opens the possibility to photopattern n-type regions within an otherwise p-type film, which has a potential for complementary circuitry or, as shown here, thermoelectric generators made from a single solution.

Continuous Processing of Multi-Walled Carbon Nanotube-Studded Carbon Fiber Tapes for Enhanced Through-Thickness Thermal Diffusivity Composites.

Carbon fiber reinforced polymer (CFRP) composites offer advantages over traditional metallic structures, particularly specific strength and stiffness, but at much reduced thermal conductivity. Moreover, fiber-to-fiber heat conduction in the composite transverse directions is significantly lower. When these structures contain electronics (heat generators), shortfalls in heat transport can be problematic.