Flowback verses first-flush: new information on the geochemistry of produced water from mandatory reporting.

Unconventional oil and gas development uses the subsurface injection of large amounts of a variety of industrial chemicals, and there are concerns about the return of these chemical to the surface with water produced with oil and gas from stimulated wells. Produced water, including any flowback of injected fluids, must be managed so as to protect human health and the environment, and understanding the chemistry of produced water from stimulated wells is necessary to ensure the safe management of produced water. In 2014, California instituted mandatory reporting for all well stimulations, including sampling produced water two times and comprehensive chemical characterization of fluids injected and fluids recovered from stimulated wells.

Comparison of chemical-use between hydraulic fracturing, acidizing, and routine oil and gas development.

The potential hazards and risks associated with well-stimulation in unconventional oil and gas development (hydraulic fracturing, acid fracturing, and matrix acidizing) have been investigated and evaluated and federal and state regulations requiring chemical disclosure for well-stimulation have been implemented as part of an overall risk management strategy for unconventional oil and gas development. Similar evaluations for chemicals used in other routine oil and gas development activities, such as maintenance acidizing, gravel packing, and well drilling, have not been previously conducted, in part due to a lack of reliable information concerning on-field chemical-use. In this study, we compare chemical-use between routine activities and the more closely regulated well-stimulation activities using data collected by the South Coast Air Quality Monitoring District (SCAQMD), which mandates the reporting of both unconventional and routine on-field chemical-use for parts of Southern California.

Identifying chemicals of concern in hydraulic fracturing fluids used for oil production.

Chemical additives used for hydraulic fracturing and matrix acidizing of oil reservoirs were reviewed and priority chemicals of concern needing further environmental risk assessment, treatment demonstration, or evaluation of occupational hazards were identified. We evaluated chemical additives used for well stimulation in California, the third largest oil producing state in the USA, by the mass and frequency of use, as well as toxicity. The most frequently used chemical additives in oil development were gelling agents, cross-linkers, breakers, clay control agents, iron and scale control agents, corrosion inhibitors, biocides, and various impurities and product stabilizers used as part of commercial mixtures.

Physical-chemical evaluation of hydraulic fracturing chemicals in the context of produced water treatment.

Produced water is a significant waste stream that can be treated and reused; however, the removal of production chemicals-such as those added in hydraulic fracturing-must be addressed. One motivation for treating and reusing produced water is that current disposal methods-typically consisting of deep well injection and percolation in infiltration pits-are being limited. Furthermore, oil and gas production often occurs in arid regions where there is demand for new water sources.

Pairing high-frequency data with a link-node model to manage dissolved oxygen impairment in a dredged estuary.

High-frequency data and a link-node model were used to investigate the relative importance of mass loads of oxygen-demanding substances and channel geometry on recurrent low dissolved oxygen (DO) in the San Joaquin River Estuary in California. The model was calibrated using 6 years of data. The calibrated model was then used to determine the significance of the following factors on low DO: excavation of the river to allow navigation of large vessels, non-point source pollution from the agricultural watershed, effluent from a wastewater treatment plant, and non-point source pollution from an urban area.

Treatment of oil-water emulsion from the machinery industry by Fenton's reagent.

An oil-water emulsion from the machinery industry was treated using Fenton's reagent. The objective was to reduce the high chemical oxygen demand (COD) of this waste stream so that it would meet the COD effluent limit of Chinese Standard JS-7740-95. The optimal [H2O2]/[Fe2+] ratio for COD removal was 3.

Physical, chemical, and biological characteristics of compounds used in hydraulic fracturing.

Hydraulic fracturing (HF), a method to enhance oil and gas production, has become increasingly common throughout the U.S. As such, it is important to characterize the chemicals found in HF fluids to evaluate potential environmental fate, including fate in treatment systems, and human health impacts.

Performance of sanitary sewer collection system odour control devices operating in diverse conditions.

Controlling odours from sanitary sewer systems is challenging as a result of the expansive nature of these systems. Addition of oxidizing chemicals is often practiced as a mitigation strategy. One alternative is to remove odorous compounds in the gases vented from manholes using adsorptive media.

Impact of co-digestion on existing salt and nutrient mass balances for a full-scale dairy energy project.

Anaerobic digestion of manure and other agricultural waste streams with subsequent energy production can result in more sustainable dairy operations; however, importation of digester feedstocks onto dairy farms alters previously established carbon, nutrient, and salinity mass balances. Salt and nutrient mass balance must be maintained to avoid groundwater contamination and salination. To better understand salt and nutrient contributions of imported methane-producing substrates, a mass balance for a full-scale dairy biomass energy project was developed for solids, carbon, nitrogen, sulfur, phosphorus, chloride, and potassium.

Modeling the inactivation of microorganisms occluded in effluent wastewater particles to enhance operation of filtration and disinfection systems.

In disinfection systems, incomplete penetration of chlorine into effluent wastewater particles can result in a residual population of viable microorganisms. In this work, a combined experimental and numerical approach was used to quantify inactivation of microorganisms in effluent particles and identify combinations of particle removal and chlorine dose that would result in a reduction of occluded microorganisms for six full-scale facilities in the United States with different nitrification levels. The results reveal that combined chlorine is more effective for inactivating occluded microorganisms than free chlorine; model calibration results suggest that free chlorine is less effective because it is more reactive.