Adsorptive performance of bismuth-doped Ni-Zn-Co ferrite nanoparticles for the removal of methylene blue dye.

Cancer, kidney and liver damage, and even death result from water contaminated with textile dyes. This study highlighted a key approach for treating water contaminated with methylene blue (MB) dye. Bismuth-doped ferrite nanoparticles (NiZnCoBiFeO) with 0 ≤  ×  ≤ 0.

Microwave-assisted supramolecular double crosslinked chitosan-based molecularly imprinted polymer for synergistic recognition and selective recovery of Cd(II) and As(V) from water: Performance and mechanistic insights.

A novel model of the sustainable double crosslinked molecularly imprinted polymer (D-Crosslinked MIP) represented as a supramolecular imprinted polymer was synthesized via the bulk polymerization method. The primary crosslinking was fabricated using biomacromolecule chitosan as a functional monomer and glutaraldehyde as a crosslinker. The primary crosslinked was subjected to dynamic interactions in a secondary crosslinking by binding AlO-NPs and TiO-NPs, forming the supramolecular D-Crosslinked-MIP.

Valorization of polyurethane foam waste through the decoration with nano-polyaniline for dye decontamination from polluted water.

Two polyurethane polyaniline nanocomposites have been synthesized using two in situ polymerization routes of dried and wet bases to valorize the polyurethane waste. The physical and chemical properties of polyurethane-based nanocomposites were compared using SEM, XRD, FTIR, and Zeta potential. SEM images showed that the average particle size of the dried-based composite was 56 nm, while the wet-based composite had an average size of 75 nm.

Chemical activation and magnetization of carbonaceous materials fabricated from waste plastics and their evaluation for methylene blue adsorption.

In this study, novel adsorbents were synthesized via the activation and magnetization of carbon spheres, graphene, and carbon nanotubes fabricated from plastics to improve their surface area and porosity and facilitate their separation from aqueous solutions. Fourier transform infrared spectroscopy "FTIR", X-ray diffraction "XRD", energy-dispersive X-ray spectroscopy "EDX", transmission electron microscope "TEM", and X-ray photoelectron spectroscopy "XPS" affirmed the successful activation and magnetization of the fabricated materials. Further, surface area analysis showed that the activation and magnetization enhanced the surface area.

Biohybrid microcapsules based on electrosprayed CS-immobilized nanoZrV for self-healing epoxy coating development.

In this work, zirconium vanadate nanoparticles were immobilized into chitosan using a facile electrospraying technique to produce CS-ZrV hybrid microcapsules for the development of a self-healing coating. Upon assessment, hybrid microcapsules possessed desirable properties with a mean particle size of 319 μm, maintaining good thermal stability of ∼55% at 700 °C, and were subsequently incorporated into an epoxy resin to develop a biocompatible self-healing coating, CZVEx, for carbon steel corrosion protection. Scratched samples of self-healing and control coatings were analyzed in a corrosion medium of 3.

Surface modification of toner-based recyclable iron oxide self-doped graphite nanocomposite to enhance methylene blue and tetracycline adsorption.

An innovative task was undertaken to convert ubiquitous and toxic electronic waste, waste toner powder (WTP), into novel adsorbents. Alkaline modification with KOH, NaOH, and NHOH was employed for the first time to synthesize a series of surface-modified WTP with enhanced dispersibility and adsorption capacity. XRD, XRF, FTIR, and BET analyses confirmed that the prepared KOH-WTP, NaOH-WTP, and NHOH-WTP were oxygen-functionalized self-doped iron oxide-graphite nanocomposites.

Engineered eco-friendly composite membranes with superhydrophobic/hydrophilic dual-layer for DCMD system.

Considerable advancements have been made in the development of hydrophobic membranes for membrane distillation (MD). Nonetheless, the environmentally responsible disposal of these membranes poses a critical concern due to their synthetic composition. Herein, an eco-friendly dual-layered biopolymer-based membrane was fabricated for water desalination.

Catalytic fabrication of graphene, carbon spheres, and carbon nanotubes from plastic waste.

In this study, we reported sustainable and economical upcycling methods for utilizing plastics such as polyethylene terephthalate (PET) and polypropylene (PP) compiled from the garbage of a residential area as cheap precursors for the production of high-value carbon materials such as graphene (G), carbon spheres (CS), and carbon nanotubes (CNTs) using different thermal treatment techniques. Graphene, carbon spheres, and carbon nanotubes were successfully synthesized from PET, PP, and PET, respectively catalytic pyrolysis. XRD and FTIR analyses were conducted on the three materials, confirming the formation of carbon and their graphitic structure.

Developing a sustainable grease from jojoba oil with plant waste based nanoadditives for enhancement of rolling bearing performance.

This paper presents a novel grease from jojoba oil and activated carbon nanoparticles (ACNPs) extracted from banana peel waste. The raw jojoba oil and ACNPs are first characterized for structural properties. Samples of jojoba grease blended with 0.

Surface-decorated porphyrinic zirconium-based metal-organic frameworks (MOFs) using post-synthetic self-assembly for photodegradation of methyl orange dye.

We report herein the surface decoration of a water-soluble free-base porphyrin, namely, 5,10,15,20-tetrakis(1-methyl-4-pyridinio)porphyrin-tetra(-toluenesulfonate) (HTMPyP), over three different zirconium-based metal-organic frameworks of different linker structure and functionality; namely UiO66, UiO66-NH, and MIP-202, self-assembly. The synthesized MOFs along with the resulting complexes have been characterized spectroscopic and analytical techniques (XRD, FT-IR, TEM, N adsorption/desorption, and laser scanning confocal microscopy). The self-assembly of HTMPyP with the examined three MOFs was observed by using the steady-state absorption and fluorescence, as well as the fluorescence lifetime studies.

Effective degradation of tetracycline via persulfate activation using silica-supported zero-valent iron: process optimization, mechanism, degradation pathways and water matrices.

Pure zero-valent iron (ZVI) was supported on silica and starch to enhance the activation of persulfate (PS) for tetracycline degradation. The synthesized catalysts were characterized by microscopic and spectroscopic methods to assess their physical and chemical properties. High tetracycline removal (67.

Optical Properties of Cationic Perylenediimide Nanowires in Aqueous Medium: Experimental and Computational Studies.

Cationic perylenediimide derivative, namely N,N'-di(2-(trimethylammoniumiodide)ethylene) perylenediimide (TAIPDI), has been synthesized and characterized in an aqueous medium by using dynamic light scattering (DLS), X-ray diffraction (XRD), fourier-transform infrared (FTIR), scanning electron microscope (SEM), and high-resolution transmission electron microscopy (HRTEM) techniques. The optical absorption and fluorescence spectra of TAIPDI revealed the formation of aggregated TAIPDI nanowires in water, but not in organic solvents. In order to control the aggregation behavior, the optical properties of TAIPDI have been examined in different aqueous media, namely cetyltrimethylammonium bromide (CTAB), and sodium dodecyl sulfate (SDS).

Green valorization of end-of-life toner powder to iron oxide-nanographene nanohybrid as a recyclable persulfate activator for degrading emerging micropollutants.

The sustainable management of toner waste (T-raw) was performed via carbonization at 500 °C (T-500) and 600 °C (T-600) to produce iron oxide-nanographene nanohybrid (FeO-NG) for activating persulfate (PS) to efficiently degrade dyes (methylene blue, MB), antibiotics (sulfamethazine, SMZ), and pesticides (diazinon, DZN). Morphology, crystallinity, chemical structure, chemical composition, surface area, and pore size distribution of the synthesized materials were investigated using various analyses. High degradation ratios of MB were attained over a wide pH range (2-7), and the optimum operating conditions were determined.

Effective decontamination of methylene blue from aqueous solutions using novel nano-magnetic biochar from green pea peels.

The conversion of agricultural waste into high-value carbon products has been an attractive area in waste management strategy. This study highlighted the synthesis and effectiveness of green pea peels (GPP), green pea biochar (GPBC), and nano-ferromagnetic green pea biochar (NFGPBC) by the ferrous/ferric co-precipitation synthesis method for eliminating cationic dyes molecules from solutions. The morphological, physicochemical, and structural properties of GPP, GPBC, and NFGPBC were approved by Scanning Electron Microscopy (SEM), Transmission Emission Microscopy (TEM), Energy Dispersive X-ray (EDX), Bruneau Emmett Teller (BET), Fourier Transform Infrared spectroscopy (FTIR), and X-ray Diffraction (XRD) techniques.

The superior performance of silica gel supported nano zero-valent iron for simultaneous removal of Cr (VI).

Pure nano zero-valent iron (NZVI) was fabricated under optimum conditions based on material production yield and its efficiency toward acid blue dye-25 decolorization. The optimum prepared bare NZVI was immobilized with two different supports of silica and starch to fabricate their composites nanomaterials. The three different prepared zero-valent iron-based nanomaterials were evaluated for removal of hexavalent chromium (Cr(VI)).

Electrospraying of Bio-Based Chitosan Microcapsules Using Novel Mixed Cross-Linker: Experimental and Response Surface Methodology Optimization.

Chitosan microcapsules draw attention due to their biodegradability, biocompatibility, antibacterial behavior, low cost, easy processing, and the capability to be used for different applications. This study utilized the electrospraying technique for the chitosan microcapsules formulation. As a novel cross-linking agent, a mixture of oxalic acid and sodium phosphate dibasic was utilized as a collecting solution for the first time in the electrospraying of chitosan microcapsules.

Investigating the Adsorption Behavior of Polyaniline and Its Clay Nanocomposite towards Ammonia Gas.

Air pollution and control of gaseous air pollutants are global concerns. Exposure to these gaseous contaminants causes several health risks, especially exposure to irritant gases such as ammonia (NH). Furthermore, the application of smart polymeric nanocomposites in environmental applications has gained significant interest in recent years.

Novel aspartic-based bio-MOF adsorbent for effective anionic dye decontamination from polluted water.

In this study, a cost-effective powdered Zn l-aspartic acid bio-metal organic framework (Zn l-Asp bio-MOF) was reported as an efficient adsorbent for Direct Red 81 (DR-81) as an anionic organic dye. The prepared bio-MOF was characterized using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), field emission transmission electron microscopy (FETEM), surface area analysis (BET), and thermal gravimetrical analysis (TGA). The resulting bio-MOF has a large surface area (180.

Assessment of antimicrobial, cytotoxicity, and antiviral impact of a green zinc oxide/activated carbon nanocomposite.

This work deals with the synthesis of zinc oxide nanoparticles/activated carbon (ZnO NPs/AC) nanocomposites with different weight ratios (3:1, 1:1, and 1:3), where the antimicrobial, antiviral, and cytotoxicity impact of the formulated nanocomposites were evaluated versus the crude ZnO and AC samples. The formula (3:1; designated Z3C1) exhibited the utmost bactericidal effect against Gram positive group, unicellular and filamentous fungi. Regarding Gram negative group, the sample (Z3C1) was remarkably effective against Klebsiella pneumonia, unlike the case of Escherichia coli.

Novel fabricated low-cost hybrid polyacrylonitrile/polyvinylpyrrolidone coated polyurethane foam (PAN/PVP@PUF) membrane for the decolorization of cationic and anionic dyes.

Dyes are recalcitrait organic pollutants threatening the aquatic environment and human health. In the present study, a novel low-cost hybrid membrane was fabricated by coating polyurethane foam (PUF) with polyacrylonitrile/polyvinylpyrrolidone (PAN/PVP) via phase inversion technique from casting solutions consisting of PAN and PVP with Dimethyl formamide (DMF) and applied for removal of cationic (Methylene Blue (MB)) and anionic (Methyl Orange (MO)) dyes from aqueous solutions. The as-prepared membrane was first characterized by Scan Electron Microscope (SEM), Fourier Transform Infrared (FTIR), Energy Dispersive Spectrometry (EDS), etc.

Utilization of iron waste from steel industries in persulfate activation for effective degradation of dye solutions.

The performance of three solid iron wastes (SIW-1, SIW-2 and SIW-3) was evaluated as an activator of persulfate (PS) for the degradation of methylene blue (MB). SIW-3 showed the highest performance among the three catalysts. The morphology, chemical composition and chemical structure of the three SIW were investigated using various analyses.

Fe Nanoparticle Size Control of the Fe-MOF-Derived Catalyst Using a Solvothermal Method: Effect on FTS Activity and Olefin Production.

The design of a highly active Fe-supported catalyst with the optimum particle and pore size, dispersion, loading, and stability is essential for obtaining the desired product selectivity. This study employed a solvothermal method to prepare two Fe-MIL-88B metal-organic framework (MOF)-derived catalysts using triethylamine (TEA) or NaOH as deprotonation catalysts. The catalysts were analyzed using X-ray diffraction, N-physisorption, Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, H temperature-programed reduction, and thermogravimetric analysis and were evaluated for the Fischer-Tropsch synthesis performance.

Monothetic Analysis and Response Surface Methodology Optimization of Calcium Alginate Microcapsules Characteristics.

Owing to bio-polymer's low-cost, environmental friendliness and mechanically stable nature, calcium alginate microcapsules have attracted much interest for their applications in numerous fields. Among the common production methods, the Electrospraying technique has shown a great potential due to smaller shape capsule production and ease of control of independent affecting parameters. Although one factor at a time (OFAT) can predict the trends of parameter effect on size and sphericity, it is inefficient in explaining the complex parameter interaction of the electrospray process.

Methyl Orange Biodegradation by Immobilized Consortium Microspheres: Experimental Design Approach, Toxicity Study and Bioaugmentation Potential.

Methyl orange (MO) is categorized among the recalcitrant and refractory xenobiotics, representing a significant burden in the ecosystem. To clean-up the surrounding environment, advances in microbial degradation have been made. The main objective of this study was to investigate the extent to which an autochthonous consortium immobilized in alginate beads can promote an efficient biodegradation of MO.

Statistical modeling of methylene blue degradation by yeast-bacteria consortium; optimization via agro-industrial waste, immobilization and application in real effluents.

The progress in industrialization everyday life has led to the continuous entry of several anthropogenic compounds, including dyes, into surrounding ecosystem causing arduous concerns for human health and biosphere. Therefore, microbial degradation of dyes is considered an eco-efficient and cost-competitive alternative to physicochemical approaches. These degradative biosystems mainly depend on the utilization of nutritive co-substrates such as yeast extract peptone in conjunction with glucose.