Mass Transfer and Optical Properties of Active PET/PP Food-Grade Films Impregnated with Olive Leaf Extract.

A supercritical solvent impregnation (SSI) technique was employed to incorporate, by batch- and semicontinuous-modes, bioactive olive leaf extract (OLE) into a food-grade multilayer polyethylene terephthalate/polypropylene (PET/PP) film for active food packaging applications. The inclusion of OLE in the polymer surfaces significantly modified the colour properties of the film. A correlation of 87.

Reinforcement of Refined and Semi-Refined Carrageenan Film with Nanocellulose.

Carrageenans obtained from seaweeds can be processed into films for a range of applications including food packaging. The level of carrageenan refinement during extraction can influence the key properties, with semi-refined carrageenan (SRC) containing more impurities than the more refined carrageenan (RC). Further refinement steps, however, result in higher costs associated with the production of RC.

A Review of Property Enhancement Techniques for Carrageenan-based Films and Coatings.

Carrageenan, a polysaccharide extracted from marine algae, is becoming increasingly regarded as a promising renewable biomaterial that has strong potential as a substitute for conventional synthetic plastics. Materials derived from carrageenans have been widely investigated over the recent decades for use in pharmaceutical and biomedical applications through to edible films and coatings. In the area of flexible films, carrageenans suffer from limitations that are primarily a result of their inherent hydrophilicity.

Current and Emerging Techniques for High-Pressure Membrane Integrity Testing.

Ideally, pressure driven membrane processes used in wastewater treatment such as reverse osmosis and nanofiltration should provide a complete physical barrier to the passage of pathogens such as enteric viruses. In reality, manufacturing imperfections combined with membrane ageing and damage can result in breaches as small as 20 to 30 nm in diameter, sufficient to allow enteric viruses to contaminate the treated water and compromise public health. In addition to continuous monitoring, frequent demonstration of the integrity of membranes is required to provide assurance that the barrier to the passage of such contaminants is intact.

Influence of acid hydrolysis, saponification and sample clean-up on the measurement of phytosterols in dairy cattle feed using GC-MS and GC with flame ionization detection.

The fortification of processed foods including dairy products is increasingly commonplace with phytosterols among many compounds used to improve the nutritional value of food products. It is also increasingly common practice for some dairy cattle feeds to be fortified for their potential to increase phytosterol levels in milk. In this study, a combined, streamlined protocol using acid hydrolysis, saponification and sample clean-up was developed to enable the rapid and reliable measurement of phytosterols.

Optimisation of β-cyclodextrin inclusion complexes with natural antimicrobial agents: thymol, carvacrol and linalool.

Beta-cyclodextrin (β-CD) inclusion complexes with naturally derived antimicrobial (AM) agents: thymol, carvacrol and linalool were prepared using a co-precipitation technique. Conditions including solvent composition, temperature, reaction time and total solvent volume were investigated to optimise the inclusion efficiency (IE) and yield. Electrospray ionisation mass spectrometry was used to confirm the formation of the thymol/β-CD complex and gas chromatography was used to quantify the amount AM agent that was encapsulated, absorbed onto the surface, or remaining in the filtered solvent.

Development and characterisation of HPMC films containing PLA nanoparticles loaded with green tea extract for food packaging applications.

A novel active film material based on hydroxypropyl-methylcellulose (HPMC) containing poly(lactic acid) (PLA) nanoparticles (NPs) loaded with antioxidant (AO) green tea extract (GTE) was successfully developed. The PLA NPs were fabricated using an emulsification-solvent evaporation technique and the sizes were varied to enable a controlled release of the AO from the HPMC matrix. A statistical experimental design was used to optimise the synthesis of the NPs in order to obtain different sizes of nanoparticles and the loading of these into the HPMC matrix was also varied.

A review of poly(lactic acid)-based materials for antimicrobial packaging.

Poly(lactic acid) (PLA) can be synthesized from renewable bio-derived monomers and, as such, it is an alternative to conventional petroleum-based polymers. Since PLA is a relatively new polymer, much effort has been directed toward its development in order to make it an acceptable and effective option to the more traditional petroleum-based polymers. Commercially, PLA has received considerable attention in food packaging applications with a focus on films and coatings that are suitable for short shelf life and ready-to-eat food products.

Physical, mechanical and barrier properties of corn starch films incorporated with plant essential oils.

Corn starch-based films are inherently brittle and lack the necessary mechanical integrity for conventional packaging. However, the incorporation of additives can potentially improve the mechanical properties and processability of starch films. In this work two essential oils, Zataria multiflora Boiss (ZEO) or Mentha pulegium (MEO) at three levels (1%, 2% and 3% (v/v)), were incorporated into starch films using a solution casting method to improve the mechanical and water vapor permeability (WVP) properties and to impart antimicrobial activity.

Antimicrobial activity of natural agents coated on starch-based films against Staphylococcus aureus.

This study investigated the antimicrobial (AM) activity of starch-based films coated with linalool, carvacrol, or thymol against Staphylococcus aureus in vitro or inoculated on the surface of Cheddar cheese. In solid media using the agar diffusion method, the inhibitory effect of linalool, carvacrol, or thymol coated onto the films increased significantly (P≤ 0.05) with the increase in concentration of each AM agent.

Essential oils and their principal constituents as antimicrobial agents for synthetic packaging films.

Spices and herbal plant species have been recognized to possess a broad spectrum of active constituents that exhibit antimicrobial (AM) activity. These active compounds are produced as secondary metabolites associated with the volatile essential oil (EO) fraction of these plants. A wide range of AM agents derived from EOs have the potential to be used in AM packaging systems which is one of the promising forms of active packaging systems aimed at protecting food products from microbial contamination.

Antimicrobial activity of biodegradable polysaccharide and protein-based films containing active agents.

Significant interest has emerged in the introduction of food packaging materials manufactured from biodegradable polymers that have the potential to reduce the environmental impacts associated with conventional packaging materials. Current technologies in active packaging enable effective antimicrobial (AM) packaging films to be prepared from biodegradable materials that have been modified and/or blended with different compatible materials and/or plasticisers. A wide range of AM films prepared from modified biodegradable materials have the potential to be used for packaging of various food products.

Release of naturally derived antimicrobial agents from LDPE films.

The migration of the naturally derived antimicrobial (AM) agents, linalool, carvacrol, and thymol, from low-density polyethylene (LDPE) films containing ethylene vinyl acetate (EVA) copolymer into the food simulants, isooctane and various ethanol/water mixtures, was studied with a view towards examining the applicability of a first-order kinetic approach as well as a diffusion model approach for describing these systems. The results suggest that the proposed models adequately describe the release of AM agents. The combination of kinetic and diffusion analyses can provide additional information about the release process using the same data set.

Quantitative analysis of polyethylene blends by Fourier transform infrared spectroscopy.

The quantitative analysis of binary polyethylene (PE) blends by Fourier transform infrared (FT-IR) spectroscopy has been achieved based on the ratio of two absorbance peaks in an FT-IR spectrum. The frequencies for the absorbance ratio are selected based on structural entities of the PE components in the blend. A linear relationship between the absorbance ratio and the blend composition was found to exist if one of the absorbance peaks is distinct to one of the components and the other peak is common to both components.