X-IGA Used for Orthotropic Material Crack Growth.

In this paper, we propose a new approach for numerically simulating the growth of cracks in unidirectional composite materials, termed extended isogeometric analysis, evaluating the maximum stress intensity factor and T-stress. To validate our approach, we used a small anisotropic plate with two edge cracks, beginning with formulating the governing equations based on the energy integral method, Stroh's Formula, and the Elastic Law describing the behaviour of anisotropic materials, while considering boundary conditions and initial states. A MATLAB code was developed to solve these equations numerically and to post-process the tensile stress and the stress intensity factor (SIF) in the first mode.

Calculation of Homogenized Mechanical Coefficients of Fiber-Reinforced Composite Using Finite Element Method.

Determining the mechanical properties of a composite material represents an important stage in its design and is generally a complicated operation. These values are influenced by the topology and geometry of the resulting composite and the values of the elastic constants of the components. Due to the importance of this subject and the increasing use of composite materials, different calculation methods have been developed over the last fifty years.

Numerical Study of Crack Prediction and Growth in Automotive Wheel Rims.

Finite element analysis has become an essential tool for simulating and understanding crack growth. This technique holds significant importance in the field of mechanical engineering, where it finds wide application in the design and optimization of structural components and material properties. This work began with the identification of critical zones and estimated the number of load life repeats through fatigue analysis, specifically applied to automotive rims utilizing innovative finite element methods.

Elastic Constants of Polymeric Fiber Composite Estimation Using Finite Element Method.

Determining the properties of composite materials (knowing the properties of the component phases) is a primary objective in the design phase. Numerous methods have been developed to determine the elastic constants of a composite material. All these methods are laborious and require significant computing time.

Finite-Element-Analysis-Based Study of a Failure Phenomenon in HDPE Pipes.

In pipes made of HDPE used in city water supply networks, a specific type of failure is commonly noted, called the parrot's beak failure. It requires expensive intervention. The prediction and study of the development of this defect, therefore, requires thorough research.

Dimensional Methods Used in the Additive Manufacturing Process.

It is a well-known fact that in the field of modern manufacturing processes, additive manufacturing (AM) offers unexpected opportunities for creativity and rapid development. Compared with classical manufacturing technologies, AM offers the advantages of reducing weight and improving performance and offers excellent design capabilities for prototyping and rapid sample manufacture. To achieve its full potential regarding cost, durability, material consumption, and rigidity, as well as maintaining competitiveness, there are several research directions that have not been explored.

Modeling Study of the Creep Behavior of Carbon-Fiber-Reinforced Composites: A Review.

The aim of this paper is to present some important practical cases in the analysis of the creep response of unidirectional fiber-reinforced composites. Some of the currently used models are described: the micromechanical model, homogenization technics, the Mori-Tanaka method, and the finite element method (FEM). Each method was analyzed to determine its advantages and disadvantages.

EDM of Ti-6Al-4V under Nano-Graphene Mixed Dielectric: A Detailed Investigation on Axial and Radial Dimensional Overcuts.

Ti-6Al-4V is considered a challenging material in terms of accurate machining. Therefore, electric discharge machining (EDM) is commonly engaged, but its low cutting rate depreciates its use. This issue is resolved if graphene nanoparticles are mixed in the dielectric.

A Mixed Iteration Method to Determine the Linear Material Parameters in the Study of Creep Behavior of the Composites.

This paper presents and applies a mixed iteration method to determine the nonlinear parameters of the material used to study a composite's creep behavior. To describe the research framework, we made a synthetic presentation of the viscoelastic behavior of composite materials by applying classical models. Further, the presented method was based on a calculation algorithm and program, which was applied on several types of materials.

Investigations on Melt Flow Rate and Tensile Behaviour of Single, Double and Triple-Sized Copper Reinforced Thermoplastic Composites.

Thermoplastic composite materials are emerging rapidly due to the flexibility of attaining customized mechanical and melt flow properties. Due to high ductility, toughness, recyclability, and thermal and electrical conductivity, there is ample scope of using copper particles in thermoplastics for 3d printing applications. In the present study, an attempt was made to investigate the Melt Flow Index (MFI), tensile strength, and electrical and thermal conductivity of nylon 6 and ABS (acrylonitrile butadiene styrene) thermoplastics reinforced with copper particles.

Finite Element Method-Based Simulation Creep Behavior of Viscoelastic Carbon-Fiber Composite.

Usually, a polymer composite with a viscoelastic response matrix has a creep behavior. To predict this phenomenon, a good knowledge of the properties and mechanical constants of the material becomes important. Schapery's equation represents a basic relation to study the nonlinear viscoelastic creep behavior of composite reinforced with carbon fiber (matrix made by polyethrtethrtketone (PEEK) and epoxy resin).