Thin-Walled Cross-Linked Acetabular Liners Need Not Exhibit Reduced Locking Strength.

Use of larger diameter femoral heads has emerged as a promising strategy to reduce the risk of dislocation after total hip arthroplasty, but thinning the walls of cross-linked ultra-high-molecular-weight polyethylene (UHMWPE) acetabular liners to accommodate these larger heads may compromise the locking mechanism of the liner. The purpose of this study was to test the mechanical integrity of the locking mechanism in cross-linked and re-melted UHMWPE acetabular components with reduced wall thickness. The locking mechanism of cross-linked (100 kGy/re-melted) acetabular liners in sizes 50/28, 50/36, and 52/36 mm of 1 design was evaluated by lever-out tests and torsion tests.

Reduced UHMWPE wear using magnesia-stabilized zirconia instead of CoCr femoral components in a knee simulator.

Magnesia-stabilized zirconia (Mg-PSZ) is stable and maintains a scratch-resistant surface in hip replacement, but is untested in knees. We assessed whether using Mg-PSZ instead of cobalt-chromium (CoCr) femoral components resulted in less tibial insert wear, and evaluated changes in topography and roughness of the femoral components. Inserts bearing against CoCr or Mg-PSZ were tested using standard (9 Mc) and aggressive (6 Mc) waveforms.

Vancomycin concentration in synovial fluid: direct injection into the knee vs. intravenous infusion.

The purpose of this study was to measure joint and serum levels of vancomycin following intra-articular (IA) or intravenous (IV) administration, and to compare the concentrations achieved in the joint fluid. IA vancomycin was only used to treat revision total knee arthroplasty (TKA) due to infection, while IV vancomycin was used as a prophylactic agent in primary and revision TKA. Both IA and IV vancomycin achieved therapeutic levels in the synovial fluid of the knee, but IA delivery of vancomycin resulted in peak levels that were many orders of magnitude higher, and also resulted in therapeutic serum levels.

The influence of sterilization method on articular surface damage of retrieved cruciate-retaining tibial inserts.

This observational study was designed to determine the importance of sterilization method and insert thickness as predictors of articular damage of cruciate-retaining polyethylene components used in total knee arthroplasty. Ninety-nine explanted tibial inserts were evaluated for surface damage. Severe damage modes were observed in 36 of 52 of γ-irradiated inserts but none of those sterilized by ethylene oxide.

Reinfected revised TKA resolves with an aggressive protocol and antibiotic infusion.

Background: Revision of failed two-stage revision TKA for infection is challenging, and amputation often is the only alternative.

Questions/purposes: We asked whether reinfection after two-stage revision for infection could be controlled with an aggressive revision protocol and intraarticular antibiotic infusion.

Methods: We retrospectively reviewed 18 patients (12 women, six men) who underwent revision for failed reimplantation between January 1999 and January 2008.

Reduced wear of cross-linked UHMWPE using magnesia-stabilized zirconia femoral heads in a hip simulator.

Background: To reduce wear, the ideal bearing surface in joint arthroplasty should be smooth and hydrophilic. Ceramics generally offer better wettability than metals and can be polished to a smoother finish. However, clinical studies have found no reduction in liner wear when using yttria-stabilized zirconia (Y-TZP) instead of cobalt chromium alloy (CoCr) femoral heads.

Minimal backside surface changes observed in retrieved acetabular liners.

Modular polyethylene liners offer versatility in total hip arthroplasty, but the locking mechanism may allow micromotion and backside wear. We evaluated the backside surface of 56 retrieved acetabular liners (mean 5.54 years in vivo, range 0.

Second-generation locking mechanisms and ethylene oxide sterilization reduce tibial insert backside damage in total knee arthroplasty.

This study evaluated the effects of polyethylene quality and locking mechanism on damage to the nonarticulating (backside) surface of retrieved tibial inserts in total knee arthroplasty. Inserts with peripheral capture (PC) locking mechanisms and ethylene oxide (EtO)-sterilized polyethylene were hypothesized to prevent major backside damage. A total of 156 inserts were sorted by locking mechanism and sterilization method and analyzed by damage scoring methods.

Methicillin-resistant Staphylococcus aureus in TKA treated with revision and direct intra-articular antibiotic infusion.

Background: Resistant organisms are difficult to eradicate in infected total knee arthroplasty. While most surgeons use antibiotic-impregnated cement in these revisions, the delivery of the drug in adequate doses is limited in penetration and duration. Direct infusion is an alternate technique.

Not all zirconia femoral heads degrade in vivo.

Degradation of yttria-stabilized zirconia femoral heads in vivo has been linked to increased roughening and even fracture of the femoral head. To determine whether magnesia-stabilized zirconia is better suited to resist degradation, we characterized the monoclinic phase concentration, surface topography, and microhardness of retrieved zirconia femoral heads. From previous work, we expected yttria-stabilized zirconia heads to undergo considerable tetragonal-to-monoclinic phase transformation in vivo, leading to considerably increased roughness and decreased microhardness, whereas magnesia-stabilized zirconia heads would not experience phase transformation and thus would not roughen or exhibit decreased microhardness.