Composed Multicore Fiber Structure for Extended Sensor Multiplexing with Fiber Bragg Gratings.

A novel multicore optical waveguide component based on a fiber design optimized towards selective grating inscription for multiplexed sensing applications is presented. Such a fiber design enables the increase in the optical sensor capacity as well as extending the sensing length with a single optical fiber while preserving the spatial sensing resolution. The method uses a multicore fiber with differently doped fiber cores and, therefore, enables a selective grating inscription.

Thermal tuning of a fiber-integrated Fabry-Pérot cavity.

Here, we present the thermal tuning capability of an alignment-free, fiber-integrated Fabry-Pérot cavity. The two mirrors are made of fiber Bragg gratings that can be individually temperature stabilized and tuned. We show the temperature tuning of the resonance wavelength of the cavity without any degradation of the finesse and the tuning of the individual stop bands of the fiber Bragg gratings.

Giant refractometric sensitivity by combining extreme optical Vernier effect and modal interference.

The optical Vernier effect consists of overlapping responses of a sensing and a reference interferometer with slightly shifted interferometric frequencies. The beating modulation thus generated presents high magnified sensitivity and resolution compared to the sensing interferometer, if the two interferometers are slightly out of tune with each other. However, the outcome of such a condition is a large beating modulation, immeasurable by conventional detection systems due to practical limitations of the usable spectral range.

Nanofiber-based high-Q microresonator for cryogenic applications.

We demonstrate a cryo-compatible, fully fiber-integrated, alignment-free optical microresonator. The compatibility with low temperatures expands its possible applications to the wide field of solid-state quantum optics, where a cryogenic environment is often a requirement. At a temperature of 4.

Optical Harmonic Vernier Effect: A New Tool for High Performance Interferometric Fibre Sensors.

The optical Vernier effect magnifies the sensing capabilities of an interferometer, allowing for unprecedented sensitivities and resolutions to be achieved. Just like a caliper uses two different scales to achieve higher resolution measurements, the optical Vernier effect is based on the overlap in the responses of two interferometers with slightly detuned interference signals. Here, we present a novel approach in detail, which introduces optical harmonics to the Vernier effect through Fabry-Perot interferometers, where the two interferometers can have very different frequencies in the interferometric pattern.

Multimode Fabry⁻Perot Interferometer Probe Based on Vernier Effect for Enhanced Temperature Sensing.

New miniaturized sensors for biological and medical applications must be adapted to the measuring environments and they should provide a high measurement resolution to sense small changes. The Vernier effect is an effective way of magnifying the sensitivity of a device, allowing for higher resolution sensing. We applied this concept to the development of a small-size optical fiber Fabry⁻Perot interferometer probe that presents more than 60-fold higher sensitivity to temperature than the normal Fabry⁻Perot interferometer without the Vernier effect.

Independently tunable dual-wavelength fiber oscillator with synchronized pulsed emission based on a theta ring cavity and a fiber Bragg grating array.

We present a fiber-integrated laser enabling independent tuning of two emission wavelengths with a synchronized pulsed emission. The discrete tuning concept comprises a theta cavity fiber laser (TCFL), a fiber Bragg grating (FBG) array as a versatile spectral filter, facilitating tailored tuning ranges, and optical gating to control the emission spectrum. A novel electrical driving scheme uniquely enables independently tunable multi-wavelength emission from a single laser oscillator.

Discrete tuning concept for fiber-integrated lasers based on tailored FBG arrays and a theta cavity layout.

We demonstrate a novel tuning concept for pulsed fiber-integrated lasers with a fiber Bragg grating (FBG) array as a discrete and tailored spectral filter, as well as a modified laser design. Based on a theta cavity layout, the structural delay lines originating from the FBG array are balanced, enabling a constant repetition rate and stable pulse properties over the full tuning range. The emission wavelength is electrically tuned with respect to the filter properties based on an adapted temporal gating scheme using an acousto-optic modulator.

Simultaneous measurement of temperature and refractive index using focused ion beam milled Fabry-Perot cavities in optical fiber micro-tips.

Optical fiber micro-tips are promising devices for sensing applications in small volume and difficult to access locations, such as biological and biomedical settings. The tapered fiber tips are prepared by dynamic chemical etching, reducing the size from 125 μm to just a few μm. Focused ion beam milling is then used to create cavity structures on the tapered fiber tips.

100 W average power femtosecond laser at 343 nm.

We present a femtosecond laser system delivering up to 100 W of average power at 343 nm. The laser system employs a Yb-based femtosecond fiber laser and subsequent second- and third-harmonic generation in beta barium borate (BBO) crystals. Thermal gradients within these BBO crystals are mitigated by sapphire heat spreaders directly bonded to the front and back surface of the crystals.

All-fiber 10 MHz acousto-optic modulator of a fiber Bragg grating at 1060 nm wavelength.

Acousto-optic modulation of a 1 cm fiber Bragg grating at 10.9 MHz frequency and 1065 nm wavelength is demonstrated for the first time. A special modulator design is employed to acoustically induce a dynamic radial long period grating which couples power of the fundamental mode to the higher-order modes supported by the Bragg grating.

Fiber-integrated concept to electrically tune pulsed fiber lasers based on step-chirped fiber Bragg grating arrays.

We present a novel method to discretely tune the emission wavelength of pulsed fiber-integrated lasers. As spectral filter, a step-chirped fiber Bragg grating (FBG) array is employed combining a monolithic structure with an unrivaled design freedom enabling large tuning bandwidths as well as tailored spectral characteristics towards fingerprint tuning features. Together with an electrical control mechanism ensuring programmable operation, this tuning method promotes fiber-integrated lasers to access new fields of applications e.

High temperature sensing with fiber Bragg gratings in sapphire-derived all-glass optical fibers.

A structured sapphire-derived all-glass optical fiber with an aluminum content in the core of up to 50 mol% was used for fiber Bragg grating inscription. The fiber provided a parabolic refractive index profile. Fiber Bragg gratings were inscribed by means of femtosecond-laser pulses with a wavelength of 400 nm in combination with a two-beam phase mask interferometer.

An electron beam profile instrument based on FBGs.

Along with the dose rate and the total irradiation dose measurements, the knowledge of the beam localization and the beam profile/energy distribution in the beam are parameters of interest for charged particle accelerator installations when they are used in scientific investigations, industrial applications or medical treatments. The transverse profile of the beam, its position, its centroid location, and its focus or flatness depend on the instrument operating conditions or on the beam exit setup. Proof-of-concept of a new type of charged particle beam diagnostics based on fiber Bragg gratings (FBGs) was demonstrated.

Focused ion beam post-processing of optical fiber Fabry-Perot cavities for sensing applications.

Focused ion beam technology is combined with chemical etching of specifically designed fibers to create Fabry-Perot interferometers. Hydrofluoric acid is used to etch special fibers and create microwires with diameters of 15 μm. These microwires are then milled with a focused ion beam to create two different structures: an indented Fabry-Perot structure and a cantilever Fabry-Perot structure that are characterized in terms of temperature.

Fiber Bragg grating inscription in few-mode highly birefringent microstructured fiber.

In this Letter, we present the technology of fiber Bragg grating (FBG) inscription in highly birefringent (HB) few-mode microstructured fibers (MSFs) with two different (nanosecond and femtosecond) lasers in a Talbot interferometer setup. The spectral characteristics of FBGs written in the core region of the investigated fiber, with particular modes represented by dual peaks, are presented and discussed. Furthermore, we calculate the fundamental fiber parameters (mode effective refractive index and phase modal birefringence) from the spectral characteristics and show very good agreement with the performed numerical fiber characterization.

Inscription of first-order sapphire Bragg gratings using 400 nm femtosecond laser radiation.

The paper describes the implementation of fiber Bragg gratings inscribed by femtosecond laser pulses with a wavelength of 400 nm. The use of a Talbot interferometer for the inscription process makes multiplexing practicable. We demonstrate the functionality of a three-grating multiplexing sensor and the temperature stability up to 1200 °C for a single first-order Bragg grating.

In situ FBG inscription during fiber laser operation.

We demonstrate the inscription of a 266 nm UV femtosecond pulse-induced fiber Bragg grating (FBG) in an Yb-doped fiber during optical pumping at 976 nm and the initiation of lasing with increasing grating reflectivity. Output spectra show the emission of the pumped fiber changing from the broad-ranged amplified spontaneous emission in the nonlasing case to the narrow-range laser operation due to the enhancement of FBG reflectivity during inscription. The proposed technique enables the direct characterization and control of FBG performance in fiber lasers.

All-fiber time-delay spectrometer for simultaneous spectral and temporal laser pulse characterization in the nanosecond range.

We have realized a modified time-delay spectrometer based on a step-chirped fiber Bragg grating array. This method allows simultaneous spectral and temporal characterization of pulsed light sources in the nanosecond regime, which can also be applied to the investigation of single pulses. With a spectral resolution in the 100 pm range, pulse spectrograms are measured and exemplarily used to explore the emission behavior of a wavelength-stabilized laser diode directly modulated in the nanosecond range.

Raman-on-chip device and detection fibres with fibre Bragg grating for analysis of solutions and particles.

An all-fibre based Raman-on-chip setup is introduced which enables analysis of solutions and trapped particles without microscopes or objectives. Beside the novel quartz microfluidic chip, innovative multi-core single-mode fibres with integrated fibre Bragg gratings are used for detection. The limit of quantitation is 7.

Alignment-free, all-spliced fiber laser source for CARS microscopy based on four-wave-mixing.

An environmentally-stable low-repetition rate fiber oscillator is developed to produce narrow-bandwidth pulses with several tens of picoseconds duration. Based on this oscillator an alignment-free all-fiber laser for multi-photon microscopy is realized using in-fiber frequency conversion based on four-wave-mixing. Both pump and Stokes pulses for coherent anti-Stokes Raman scattering (CARS) microscopy are readily available from one fiber end, intrinsically overlapped in space and time, which drastically simplifies the experimental handling for the user.

Multicore fiber with integrated fiber Bragg gratings for background-free Raman sensing.

In the last years a variety of fiber optic Raman probes emerged, which are only partly suited for in vivo applications. The in vivo capability is often limited by the bulkiness of the probes. The size is associated with the required filtering of the probes, which is necessary due to Raman scattering inside the fibers.

Bending insensitivity of fiber Bragg gratings in suspended-core optical fibers.

This Letter presents simulation and experimental results that explore bending insensitivity of fiber Bragg gratings in suspended-core optical fibers. The implementation of thin silica bridge in the fibers enhances index contrast of the fiber core and reduces bending-induced strain transfer to the fiber core. This fiber design lead to a reduction of over 7 times in strain-induced fiber Bragg grating resonant peak shifts in the suspended-core fiber compared with that in standard telecommunication fiber, and an 0.

Suspended-core fiber Bragg grating sensor for directional-dependent transverse stress monitoring.

This Letter presents simulation and experimental results of orientation-dependent transverse stress fiber sensors using fiber Bragg gratings (FBGs) inscribed in four-hole suspended-core fibers. Resonant peak shifts and splitting of FBGs were studied as functions of the applied transverse load and fiber orientation. Both simulation and experimental results revealed that the response of FBGs in suspended-core fibers is sensitive to both the orientation and magnitude of an applied transverse stress.

Post-hydrogen-loaded draw tower fiber Bragg gratings and their thermal regeneration.

The idea of Bragg gratings generated during the drawing process of a fiber dates back almost 20 years. The technical improvement of the draw tower grating (DTG) process today results in highly reliable and cost-effective Bragg gratings for versatile application in the optical fiber sensor market. Because of the single-pulse exposure of the fiber, the gratings behave typically like type I gratings with respect to their temperature stability.