PNA-PEG modified silicon platforms as functional bio-interfaces for applications in DNA microarrays and biosensors.

The synthesis and characterization of two types of silicon-based biofunctional interfaces are reported; each interface bonds a dense layer of poly(ethylene glycol) (PEG(n)) and peptide nucleic acid (PNA) probes. Phosphonate self-assembled monolayers were derivatized with PNA using a maleimido-terminated PEG(45). Similarly, siloxane monolayers were functionalized with PNA using a maleimido-terminated PEG(45) spacer and were subsequently modified with a shorter methoxy-terminated PEG(12) ("back-filling").

Structural characterization of an elevated lipid bilayer obtained by stepwise functionalization of a self-assembled alkenyl silane film.

This work reports a novel tethered lipid membrane supported on silicon oxide providing an improved model cell membrane. There is an increasing need for robust solid supported fluid model membranes that can be easily deposited on soft cushions. In such architecture the space between the membrane and the substrate should be tunable in the nanometer range.

Spectroscopic studies of metal binding and metal selectivity in Bacillus subtilis BSco, a Homologue of the Yeast Mitochondrial Protein Sco1p.

Sco1 is a mitochondrial membrane protein involved in the assembly of the CuA site of cytochrome c oxidase. The Bacillus subtilis genome contains a homologue of yeast Sco1, YpmQ (hereafter termed BSco), deletion of which leads to a phenotype lacking in caa3 (CuA-containing) oxidase activity but expressing normal levels of aa3 (quinol) oxidase activity. Here, we report the characterization of the metal binding site of BSco in its Cu(I)-, Cu(II)-, Zn(II)-, and Ni(II)-bound forms.

Self-assembled monolayers and polymer brushes in biotechnology: current applications and future perspectives.

The chemistry and topography of a surface affect biological response and are of fundamental importance, especially when living systems encounter synthetic surfaces. Most biomolecules have immense recognition power (specific binding) and simultaneously have a tendency to physically adsorb onto a solid substrate without specific receptor recognition (nonspecific adsorption). Therefore, to create useful materials for many biotechnology applications, interfaces are required that have both enhanced specific binding and reduced nonspecific binding.

Oligo(ethylene glycol) containing polymer brushes as bioselective surfaces.

The nitroxide-mediated polymerization of styrenic monomers containing oligo(ethylene glycol) (OEGn) moieties was chosen for the preparation of biocompatible polymer brushes tethered to silicon oxide surfaces due to the broad range of monomer structures available and the use of a nonmetallic initiator. These surfaces were characterized by near-edge X-ray absorption fine structure and water contact angle measurements. The biocompatibility of these grown polymer brushes was studied and compared with deposited assemblies of surface-bound OEGn-terminated silanes with selected chain lengths.

Control of surface properties using fluorinated polymer brushes produced by surface-initiated controlled radical polymerization.

Surface-grafted styrene-based homopolymer and diblock copolymer brushes bearing semifluorinated alkyl side groups were synthesized by nitroxide-mediated controlled radical polymerization on planar silicon oxide surfaces. The polymer brushes were characterized by X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine structure (NEXAFS), and time-dependent water contact angle measurements. Angle-resolved XPS studies and water contact angle measurements showed that, in the case of the diblock copolymer brushes, the second block to be added was always exposed at the polymer-air interface regardless of its surface energy.

Coatings based on side-chain ether-linked poly(ethylene glycol) and fluorocarbon polymers for the control of marine biofouling.

The preparation of side group modified polystyrene-based surface-active block copolymers (SABC) for use as marine fouling resistance/release applications is described. Modifying moieties such as poly(ethylene glycol) (PEG) and semifluorinated segments were used. A novel bilayer methodology has been employed that provides both suitable mechanical properties through the use of an elastomeric primer layer of styrene-ethylene/butylene-styrene (SEBS) and control of surface-chemistry through use of the SABCs.