A Preliminary Stability Assessment of Three State-of-the-Art CAD/CAM Materials Under Human Gingival Cell Culture.

CAM/CAD composites are widely used as dental restoration materials due to their resistivity to wear. The purpose of this study was to determine the effect of human gingival fibroblast cells on three different computer-aided design/computer-aided manufacturing (CAD/CAM) hybrid materials with resin-based composites (RBC) and to assess their stability following cell growth. The CAM/CAD dental materials were investigated in different conditions as follows: (i) cells (human gingival fibroblasts, HFIB-Gs) incubated over the material for each sample, denoted as A; (ii) reference, the raw material, denoted as B; and (iii) materials incubated in DMEM medium, denoted as C.

Performance Assessment of Three Similar Dental Restorative Composite Materials via Raman Spectroscopy Supported by Complementary Methods Such as Hardness and Density Measurements.

(1) Background: A widespread problem in oral health is cavities produced by cariogenic bacteria that consume fermentable carbohydrates and lower pH to 5.5-6.5, thus extracting Ca and phosphate ions (PO) from teeth.

Periodontal Disease Monitoring by Raman Spectroscopy of Phosphates: New Insights into Pyrophosphate Activity.

(1) Background: The intent of this survey was to investigate the quality of the alveolar bone by revealing the different phases for calcified tissues independent of the medical history of the patient in relation to periodontal disease by means of Raman spectroscopy and then to correlate the results by suggesting a possible mechanism for the medical impairment; (2) Methods: The investigation was mainly based on Raman spectroscopy that was performed in vivo during surgery for the selected group of patients. The targeted peaks for the Raman spectra were according to the reference compounds (e.g.

Preliminary Assessment of In Vivo Raman Spectroscopy Technique for Bone Quality Evaluation of Augmented Maxillary Sinus Floor.

(1) Background: In oral surgery, bone regeneration is achieved through various types of bone grafts or bone substitutes and its success is usually analyzed by micro-computed tomography and histomorphometry. The aim of this study was to evaluate the usefulness of Raman spectroscopy as an alternative to other techniques for bone quality evaluation during a standard oral surgery procedure. (2) Methods: The preliminary evaluation of bone augmentation during maxillary sinus floor elevation oral surgery was performed by Raman spectroscopy for several (five) patients during and after the surgery and the results were compared with postoperative data from histomorphometry, EDX and SEM analysis.

Raman Spectroscopy as Spectral Tool for Assessing the Degree of Conversion after Curing of Two Resin-Based Materials Used in Restorative Dentistry.

(1) Background: The treatment of dental cavities and restoration of tooth shape requires specialized materials with specific clinical properties, including being easy to model, light-cured, having a natural color, reduced shrinkage, a hardness similar to hydroxyapatite, and no leakage. The dimensional stability of resin composite materials is affected by polymerization shrinkage, degree of conversion (number of π carbon bonds converted into σ ones), thermal contraction and expansion, and interactions with an aqueous environment. (2) Methods: The materials used in our investigation were two composite resins with similar polymer matrices, but different filler (micro/nano filler).

Raman Spectroscopy: In Vivo Application for Bone Evaluation in Oral Reconstructive (Regenerative) Surgery.

The aim of this study was to evaluate the quality of the bone, revealing the different phases for calcified tissues independent of the medical history of the patient in relation to periodontitis by means of in vivo Raman spectroscopy. Raman spectroscopy measurements were performed in vivo during surgery and then ex vivo for the harvested bone samples for the whole group of patients (ten patients). The specific peaks for the Raman spectrum were traced for reference compounds (e.

3D Superparamagnetic Scaffolds for Bone Mineralization under Static Magnetic Field Stimulation.

We reported on three-dimensional (3D) superparamagnetic scaffolds that enhanced the mineralization of magnetic nanoparticle-free osteoblast cells. The scaffolds were fabricated with submicronic resolution by laser direct writing via two photons polymerization of Ormocore/magnetic nanoparticles (MNPs) composites and possessed complex and reproducible architectures. MNPs with a diameter of 4.

Evaluation of the quality of local butters: A new approach based on Raman spectroscopy and supported by the classical pycnometer method.

In this study, the quality of the local Romanian butters was investigated using the classical pycnometer and optic microscopy methods, combined with Raman spectroscopy. We used a pool of 10 samples with different characteristics, and analyzed them by the three aforementioned methods. Pycnometric measurements showed a direct correlation between the fat content and the density values of the samples.

Pulsed Laser Fabrication of TiO Buffer Layers for Dye Sensitized Solar Cells.

We report on the fabrication of dye-sensitized solar cells with a TiO buffer layer between the transparent conductive oxide substrate and the mesoporous TiO film, in order to improve the photovoltaic conversion efficiency of the device. The buffer layer was fabricated by pulsed laser deposition whereas the mesoporous film by the doctor blade method, using TiO paste obtained by the sol-gel technique. The buffer layer was deposited in either oxygen (10 Pa and 50 Pa) or argon (10 Pa and 50 Pa) onto transparent conducting oxide glass kept at room temperature.

3D Biomimetic Magnetic Structures for Static Magnetic Field Stimulation of Osteogenesis.

We designed, fabricated and optimized 3D biomimetic magnetic structures that stimulate the osteogenesis in static magnetic fields. The structures were fabricated by direct laser writing via two-photon polymerization of IP-L780 photopolymer and were based on ellipsoidal, hexagonal units organized in a multilayered architecture. The magnetic activity of the structures was assured by coating with a thin layer of collagen-chitosan-hydroxyapatite-magnetic nanoparticles composite.

Laser-direct writing by two-photon polymerization of 3D honeycomb-like structures for bone regeneration.

A major limitation of existing 3D implantable structures for bone tissue engineering is that most of the cells rapidly attach on the outer edges of the structure, restricting the cells penetration into the inner parts and causing the formation of a necrotic core. Furthermore, these structures generally possess a random spatial arrangement and do not preserve the isotropy on the whole volume. Here, we report on the fabrication and testing of an innovative 3D hierarchical, honeycomb-like structure (HS), with reproducible and isotropic arhitecture, that allows in 'volume' migration of osteoblasts.

Mechanical, Corrosion and Biological Properties of Room-Temperature Sputtered Aluminum Nitride Films with Dissimilar Nanostructure.

Aluminum Nitride (AlN) has been long time being regarded as highly interesting material for developing sensing applications (including biosensors and implantable sensors). AlN, due to its appealing electronic properties, is envisaged lately to serve as a multi-functional biosensing platform. Although generally exploited for its intrinsic piezoelectricity, its surface morphology and mechanical performance (elastic modulus, hardness, wear, scratch and tensile resistance to delamination, adherence to the substrate), corrosion resistance and cytocompatibility are also essential features for high performance sustainable biosensor devices.

Laser deposition of poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid) - lysozyme microspheres based coatings with anti-microbial properties.

The purpose of this study was to obtain, characterize and evaluate the cytotoxicity and antimicrobial activity of coatings based on poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid) - Lysozyme (P(3HB-3HV)/Lys) and P(3HB-3HV) - Polyethylene glycol - Lysozyme (P(3HB-3HV)/PEG/Lys) spheres prepared by Matrix Assisted Pulsed Laser Evaporation (MAPLE) technique, in order to obtain functional and improved Ti-based implants. Morphological investigation of the coatings by Infrared Microscopy (IRM) and SEM revealed that the average diameter of P(3HB-3HV)/Lys spheres is around 2μm and unlike the drop cast samples, IRM recorded on MAPLE films revealed a good distribution of monitored functional groups on the entire scanned surface. The biological evaluation of MAPLE structured surfaces revealed an improved biocompatibility with respect to osteoblasts and endothelial cells as compared with Ti substrates and an enhanced anti-biofilm effect against Gram positive (Staphylococcus aureus) and Gram negative (Pseudomonas aeruginosa) tested strains.

Fabrication of antimicrobial silver-doped carbon structures by combinatorial pulsed laser deposition.

We report on the selection by combinatorial pulsed laser deposition of Silver-doped Carbon structures with reliable physical-chemical characteristics and high efficiency against microbial biofilms. The investigation of the films was performed by scanning electron microscopy, high resolution atomic force microscopy, energy dispersive X-Ray Spectroscopy, X-ray diffraction, Raman spectroscopy, bonding strength "pull-out" tests, and surface energy measurements. In vitro biological assays were carried out using a large spectrum of bacterial and fungal strains, i.

Combinatorial MAPLE deposition of antimicrobial orthopedic maps fabricated from chitosan and biomimetic apatite powders.

Chitosan/biomimetic apatite thin films were grown in mild conditions of temperature and pressure by Combinatorial Matrix-Assisted Pulsed Laser Evaporation on Ti, Si or glass substrates. Compositional gradients were obtained by simultaneous laser vaporization of the two distinct material targets. A KrF* excimer (λ=248nm, τFWHM=25ns) laser source was used in all experiments.

Structural Properties and Antifungal Activity against Candida albicans Biofilm of Different Composite Layers Based on Ag/Zn Doped Hydroxyapatite-Polydimethylsiloxanes.

Modern medicine is still struggling to find new and more effective methods for fighting off viruses, bacteria and fungi. Among the most dangerous and at times life-threatening fungi is . Our work is focused on surface and structural characterization of hydroxyapatite, silver doped hydroxyapatite and zinc doped hydroxyapatite deposited on a titanium substrate previously coated with polydimethylsiloxane (HAp-PDMS, Ag:HAp-PDMS, Zn:HAp-PDMS) by different techniques: Scanning Electron Microscopy (SEM), Glow Discharge Optical Emission Spectroscopy (GDOES) and Fourier Transform Infrared Spectroscopy (FTIR).

Nitride coating enhances endothelialization on biomedical NiTi shape memory alloy.

Surface nitriding was demonstrated to be an effective process for improving the biocompatibility of implantable devices. In this study, we investigated the benefits of nitriding the NiTi shape memory alloy for vascular stent applications. Results from cell experiments indicated that, compared to untreated NiTi, a superficial gas nitriding treatment enhanced the adhesion of human umbilical vein endothelial cells (HUVECs), cell spreading and proliferation.

Structural, compositional, mechanical characterization and biological assessment of bovine-derived hydroxyapatite coatings reinforced with MgF2 or MgO for implants functionalization.

Hydroxyapatite (HA) is a consecrated biomaterial for bone reconstruction. In the form of thin films deposited by pulsed laser technologies, it can be used to cover metallic implants aiming to increase biocompatibility and osseointegration rate. HA of animal origin (bovine, BHA) reinforced with MgF2 (2wt.

Electrical, structural, and optical properties of sulfurized Sn-doped In2O 3 nanowires.

Sn-doped In2O3 nanowires have been grown on Si via the vapor-liquid-solid mechanism at 800 °C and then exposed to H2S between 300 to 600 °C. We observe the existence of cubic bixbyite In2O3 and hexagonal SnS2 after processing the Sn:In2O3 nanowires to H2S at 300 °C but also cubic bixbyite In2O3, which remains dominant, and the emergence of rhombohedral In2(SO4)3 at 400 °C. The resultant nanowires maintain their metallic-like conductivity, and exhibit photoluminescence at 3.

Electrically stimulated osteogenesis on Ti-PPy/PLGA constructs prepared by laser-assisted processes.

This work describes a versatile laser-based protocol for fabricating micro-patterned, electrically conductive titanium-polypyrrole/poly(lactic-co-glycolic)acid (Ti-PPy/PLGA) constructs for electrically stimulated (ES) osteogenesis. Ti supports were patterned using fs laser ablation in order to create high spatial resolution microstructures meant to provide mechanical resistance and physical cues for cell growth. Matrix Assisted Pulsed Laser Evaporation (MAPLE) was used to coat the patterned Ti supports with PPy/PLGA layers acting as biocompatible surfaces having chemical and electrical properties suitable for cell differentiation and mineralization.

Surface plasma functionalization influences macrophage behavior on carbon nanowalls.

The surfaces of carbon nanowall samples as scaffolds for tissue engineering applications were treated with oxygen or nitrogen plasma to improve their wettability and to functionalize their surfaces with different functional groups. X-ray photoelectron spectroscopy and water contact angle results illustrated the effective conversion of the carbon nanowall surfaces from hydrophobic to hydrophilic and the incorporation of various amounts of carbon, oxygen and nitrogen functional groups during the treatments. The early inflammatory responses elicited by un-treated and modified carbon nanowall surfaces were investigated by quantifying tumor necrosis factor-alpha and macrophage inflammatory protein-1 alpha released by attached RAW 264.

Structural and biological evaluation of lignin addition to simple and silver-doped hydroxyapatite thin films synthesized by matrix-assisted pulsed laser evaporation.

We report on thin film deposition by matrix-assisted pulsed laser evaporation of simple hydroxyapatite (HA) or silver (Ag) doped HA combined with the natural biopolymer organosolv lignin (Lig) (Ag:HA-Lig). Solid cryogenic target of aqueous dispersions of Ag:HA-Lig composite and its counterpart without silver (HA-Lig) were prepared for evaporation using a KrF* excimer laser source. The expulsed material was assembled onto TiO2/Ti substrata or silicon wafers and subjected to physical-chemical investigations.

Magneto-plasmonic biosensor with enhanced analytical response and stability.

We present novel solutions to surpass current analytic limitations of Magneto-Optical Surface Plasmon Resonance (MOSPR) assays, concerning both the chip structure and the method for data analysis. The structure of the chip is modified to contain a thin layer of Co-Au alloy instead of successive layers of homogeneous metals, as currently used. This alloy presents improved plasmonic and magnetic properties, yet a structural stability similar to Au-SPR chips, allowing for bioaffinity assays in saline solutions.

Iron oxide-based nanoparticles with different mean sizes obtained by the laser pyrolysis: structural and magnetic properties.

Nano-sized iron oxide-based particles have been directly synthesized by the laser induced pyrolysis of a mixture containing iron pentacarbonyl/air (as oxidizer)/ethylene (as sensitizer). In this paper we further demonstrate the possibility to vary the chemical composition and the nanoparticle dimensions of the iron oxide-based materials by handling the oxidation procedure in the frame of the laser pyrolysis process. Thus, nanoparticles with major maghemite/magnetite content may change composition into mixtures with variable amounts of three components: major gamma-Fe2O3/Fe3O4 iron oxide, metallic Fe and cementite Fe3C.