Impact of storage conditions on the fracture reliability and physical properties of a dental resin-based composite.

This study investigated the impact of 'storage condition' and 'period of storage' on selected physico-mechanical properties and fracture reliability of a resin-based composite (RBC). Specimens, prepared from a nanofilled RBC (Filtek Z350 XT; 3M ESPE), underwent tests for degree of conversion (DC), flexural strength (σ), flexural modulus (E), and hardness. The specimens were initially grouped into dry storage at 37°C or wet storage in distilled water at 37°C.

Full analysis of the effects of modeler liquids on the properties of direct resin-based composites: a meta-analysis review of in vitro studies.

Objectives: This study systematically revised the literature to answer the following question: do modeler liquids (MLs) affect the properties of direct resin-based composites (RBCs)?

Materials And Methods: The review followed the PRISMA statement, and the search was conducted in PubMed, Scopus, Web of Science, Embase, and Lilacs databases. Studies were included if they investigated the properties of RBCs prepared using the restorative dental modeling insertion technique (RDMIT). The risk of bias was performed with the RoBDEMAT tool.

New material perspective for endocrown restorations: effects on mechanical performance and fracture behavior.

The aim of this study was to investigate the mechanical performance and the fracture behavior of endocrown restorations prepared using distinct restorative materials. A total of 42 sound molars with similar crown size and shape were cut at 2 mm above the cementoenamel junction and endodontically treated. They were categorized according to the restorative material used to fabricate endocrown restorations (n=7), namely, conventional composite (Filtek™ Z350 XT), bulk fill composite (Filtek™ Bulk Fill), conventional composite modeled using resin adhesives (SBMP: Scotchbond™ Multipurpose Adhesive; or SBU: Scotchbond™ Universal Adhesive), and IPS e.

Bleaching and enamel surface interactions resulting from the use of highly-concentrated bleaching gels.

Tooth bleaching is considered a non-invasive treatment, although the use of highly-concentrated products may provoke increased surface roughness and enamel demineralization, as well as postoperative sensitivity. Thus, the aim of this study was to investigate whether hydrogen peroxide (HO) concentration would affect tooth bleaching effectiveness and the enamel surface properties. Enamel/dentin bovine specimens (6 × 4 mm) were immersed in coffee solution for 7 days and evaluated with a spectrophotometer (Easyshade; baseline), using the CIELab color parameters.

Effect of Diamond Bur Grit Size on Composite Repair.

Purpose: This study investigated the effect of diamond bur grit size on the repair bond strength of fresh and aged resin composites.

Materials And Methods: Blocks of microhybrid composite (Opallis, FGM) were stored in distilled water at 37°C for 24 h (fresh composite) or subjected to 5000 thermal cycles (aged composite). The surfaces were roughened using diamond-coated, flame-shaped carbide burs with medium grit (#3168), fine grit (#3168F), or extra-fine grit (#3168FF).

Application of resin adhesive on the surface of a silanized glass fiber-reinforced post and its effect on the retention to root dentin.

Introduction: In this study, the effect of different post surface treatments on the retention of glass fiber-reinforced post to root dentin was evaluated. The hypotheses tested were (1) post silanization would not improve its retention and (2) the application of silane plus resin adhesive on the post would enhance its retention.

Methods: After root canal preparation, 4 different protocols (n = 5) of post surface treatment were evaluated, combined with or without silane (Silane coupling agent) and adhesive (Scotchbond Multipurpose): silane + adhesive (S/A), only silane, only adhesive, or no treatment (control).

The effect of time between handling and photoactivation on self-adhesive resin cement properties.

Purpose: To evaluate the degree of conversion, absorption, and solubility in water of self-adhesive resin cements subjected to different time intervals between material preparation and the photoactivation procedure.

Materials And Methods: Two dual self-adhesive resin cements were tested: RelyX Unicem and SmartCem2. The degree of conversion as a function of time was evaluated by Fourier-transformed infrared spectroscopy using the attenuated total reflectance technique.

Comparative evaluation of dental resin composites based on micron- and submicron-sized monomodal glass filler particles.

Objectives: A model resin composite containing a novel monomodal inorganic filler system based on submicron-sized Ba-Si-Al glass particles (NanoFine NF180; Schott) was formulated and compared with an experimental composite containing micron-sized particles (UltraFine UF1.0; Schott).

Methods: The filler particles were characterized using X-ray microanalysis and granulometry, while the composites were characterized in terms of filler-resin morphology, radiopacity, degree of CC conversion, hardness, flexural strength/modulus, work-of-fracture, surface roughness and gloss (before and after simulated toothbrushing abrasion), and bulk compressive creep.

1,3-Diethyl-2-thiobarbituric acid as an alternative coinitiator for acidic photopolymerizable dental materials.

The ethyl-4-dimethylaminobenzoate (EDAB) is widely used as a coinitiator of the camphorquinone (CQ), but in acidic circumstances it might present some instability, reducing the polymerization efficiency of the material. Considering this, new coinitiators are being evaluated. Hence, this study evaluated the kinetic of polymerization (KP), the degree of conversion (DC), and the rate of polymerization (RP ) of experimental resin adhesives containing 1,3-diethyl-2-thiobarbituric acid (TBA) as a coinitiator of the CQ.