Bonding of resin luting materials to titanium and titanium alloy.

Recently in Japan, due to the increased prices of palladium and gold, cast titanium restorations have been included in the Japanese national health insurance system. The purpose of this review was to survey the available literature on titanium bonding systems, focusing on the adhesive monomer in the luting agent in order to expand the application of resin-bonded fixed prostheses made of titanium or titanium alloys. It was found that adhesive monomers are effective for bonding to titanium, and provide results equal to the procedures of silanization and tribochemical silica coating.

Positive end-expiratory pressure setting based on transpulmonary pressure during robot-assisted laparoscopic prostatectomy: an observational intervention study.

Background: In robot-assisted laparoscopic prostatectomy (RALP), concerns include the formation of atelectasis and reduced functional residual capacity. The present study aimed to examine the feasibility of positive end-expiratory pressure (PEEP) setting based on transpulmonary pressure (Ptp) as well as the effects of incremental PEEP on respiratory mechanics, blood gases, cerebral oxygenation (rSO), and hemodynamics.

Methods: Fourteen male patients who were scheduled to receive RALP were recruited.

Bonding performance of a thiohydantoin-methacrylate monomer on noble metal alloys.

This study assessed the effect of a primer containing 10-methacryloyloxydecyl-(2-thiohydantoin-4-yl)propionate (MDTHP) on the bonding of noble metal alloys to an acrylic resin. Three noble metal alloys were selected as adherends, and V-Primer containing 6-(4-vinylbenzyl-n-propyl)amino-1,3,5-triazine-2,4-dithione was used as a comparative control. The disk specimens of each noble metal alloy were wet-ground and divided into three conditions: specimens primed with MDTHP primer or V-Primer, and specimens without priming.

Gloss and surface roughness of pre-polymerized composite materials designed for posterior CAD/CAM crown restorations corroded with acidulated phosphate fluoride application.

This study assessed the gloss and surface roughness of computer-aided design/computer-aided manufacturing (CAD/CAM) resin composites corroded with acidulated phosphate fluoride (APF) application. One ceramic block, ten CAD/CAM resin composites for premolars, and four CAD/CAM resin composites for molars were assessed. The surface topography of the materials before and after APF application was observed using an electron microscope.

Influence of polymerization methods and priming agents on the bond strength between resin luting agents and gold alloy.

Purpose: To evaluate the influence of polymerization methods and a metal priming agent on the bond strength between gold alloy for metal ceramic restorations and dual-cure-type resin luting agents, and on the strength and hardness of the luting agents.

Methods: A total of 154 disks cast by a gold alloy were treated with or without a metal priming agent. One of the three luting agents was applied on the disk.

Bonding of Fused Quartz with an Aromatic Silane Compound and Acidic Functional Monomers with a Tri-n-butylborane Initiated Resin.

Purpose: This study evaluated the effect of an aromatic silane compound and acidic functional monomer on the bond strength of fused quartz. Materials and Methods: A total of 264 disk specimens were fabricated from fused quartz for shear bond testing. Two silane compounds were used: 3-(trimethoxysilyl)propyl methacrylate (3-TMSPMA) and 3-(4-methacryloyloxyphenyl) propyltrimethoxysilane (3-MPPTS).

Construction of Ultrathin Layer-by-Layer Films of Oligothiophene Derivatives on an Electrode.

Oligothiophene derivatives, which are known as p-type materials, have been synthesized, and their ultrathin layer-by-layer films have been constructed on an electrode using a simple and convenient dipping method. The stepwise deposition behavior of quaterthiophene and sexithiophene derivatives on the electrode via hydrogen bonding was monitored by electronic spectra measurement, and the constructed films were evaluated by X-ray photoelectron spectroscopy, grazing-incidence small-angle X-ray scattering, and cyclic voltammetry. It has been clarified that the constructed layer-by-layer films were electroactive and photoelectroactive.

Adhesive bonding of noble metals with a thiohydantoin primer.

Objective: The purpose of this study was to assess the effects of an experimental primer containing acetone solution and a sulfur-containing functional monomer, 10-methacryloyloxydecyl-(2-thiohydantoin-4-yl)propionate (MDTHP), on the bonds between noble metals and acrylic resin.

Methods: The experimental primer used as the control for comparison consisted of 6-(4-vinylbenzyl-n-propyl)amino-1,3,5-triazine-2,4-dithione (VBATDT) in acetone. These primers were prepared as equimolar functional monomers (0.

Synthesis and characterization of a methacrylate monomer with a thiohydantoin structure.

The purpose of the current study was to synthesize a methacrylate monomer with a thiohydantoin structure. In a flask, (2-thiohydantoin-4-yl) propionic acid, 10-hyroxydecyl methacrylate, 4-dimethylaminopyridine, and tetrahydrofuran (THF) were placed in a nitrogen atmosphere. A THF solution of N,N'-dicyclohexylcarbodiimide was added and stirred at room temperature.

Influence of Oxidation of Copper on Shear Bond Strength to an Acrylic Resin Using an Organic Sulfur Compound.

The aim of this study was to clarify the influence of the copper surfaces changed from Cu or CuO to CuO on the bonding strength of resin with organic sulfur compounds. The disk-shaped specimens ( = 44) of copper were wet-ground. Half of the specimens were heated at 400 °C for 4 min in an electric furnace (HT: heated).

Radiopacity of computer-aided design/computer-aided manufacturing composite resin blocks.

This study aimed to clarify the degree of difference in radiopacity between sixteen CAD/CAM composite resin blocks, one ceramic block, and teeth of the same thickness on radiographs. The radiographic density of CAD/CAM composite resin blocks was measured and the results were compared with the corresponding values for enamel and dentin. Additionally, the study analyzed the constituent elements of each type of CAD/CAM composite resin block and conducted an examination to identify those elements exerting an influence on radiopacity.

Surface properties and gloss of CAD/CAM composites after toothbrush abrasion testing.

The purpose of this study was to evaluate the surface properties and gloss of CAD/CAM composites after toothbrush abrasion testing. Four CAD/CAM composites for molars (Cerasmart 300, Estelite P block, Katana Avencia P block, and KZR-CAD HR3 Gammatheta), one CAD/CAM composite for premolars (Shofu Block HC Hard), and one feldspathic ceramics (Vitablocs Mark II) were assessed. Knoop hardness number, gloss, and surface roughness (Ra, Rz, and Sa) were measured before and after toothbrush abrasion testing.

Effect of etching with potassium hydrogen difluoride and ammonium hydrogen difluoride on bonding of a tri-n-butylborane initiated resin to zirconia.

The purpose of the current study was to evaluate the effect of etching with potassium hydrogen difluoride (KHF) and ammonium hydrogen difluoride (NHHF) on the bond strength of a self-polymerizing methyl methacrylate resin (MMA-TBB) bonded to zirconia. Zirconia disks were prepared using the following surface treatment: no treatment, alumina blasting, and etching with KHF or NHHF. The specimens were bonded with the MMA-TBB.

Properties of indirect composites polymerized with laboratory light-emitting diode units.

This study evaluated the light intensity of light-emitting diode (LED) units and the effects of five laboratory polymerization units on hardness and flexural strength. Two indirect composite materials (Cesead N and Solidex Hardura) were polymerized with five units (α-Light II, Hyper LII, LED Cure Master, Twinkle LED, and α-Light V). The light intensity of the devices was measured with a spectroradiometer.

Effect of a self-etching primer containing 4-META and sodium sulfite after phosphoric acid etching on bonding strength of MMA-TBB resin to human enamel.

Purpose: The aim of this study was to evaluate the shear bond strength and durability of MMA-TBB resin to human enamel applied a self-etching primer with phosphoric acid etching.

Methods: A self-etching primer (Teeth primer, TP) containing 4-methacryloyloxyethyl trimellitate anhydride (4-META) and sodium sulfite and two etchants having different phosphoric acid concentrations (K-etchant gel, KE, 35-45%: Red gel, RG, 20-25%) were used as treatment agent, and MMA-TBB resin was used as luting agent. Enamel surfaces were treated with six methods which were as follow: KE, RG, TP, KE+TP, and RG+TP.

Effect of multi-purpose primers on the bond durability between tri-n-butylborane initiated resin and gold alloy.

Purpose: This study investigated the influence of an interaction between sulfur-containing monomers and other monomers in multipurpose primers on the bond durability of a tri-n-butylborane (TBB)-initiated acrylic resin to a gold alloy.

Methods: The disk-shaped adherend materials were prepared from a gold alloy (Casting Gold M.C.

Effect of silane compounds on bonding to fused quartz of tri-n-butylborane initiated resin.

This study aimed to investigate how different compositions of experimental silane-based primers in a methyl methacrylate solution containing 3-(trimethoxysilyl)propyl methacrylate (3-TMSPMA) or 3-(4-methacryloyloxyphenyl)propyl trimethoxysilane (3-MPPTS) might act as silicon dioxide bonding agents. With or without post-silanization heat treatment, primer-treated quartz discs were bonded using the MMA-TBB resin and their bond strengths were evaluated. The disks were primed with one of the following materials: 1 mol% 3-TMSPMA, 2 mol% 3-TMSPMA, 1 mol% 3-MPPTS, and 2 mol% 3-MPPTS.

Trace of organic sulfur compounds detected from debonded interface between transparent acrylic resin and gold alloy.

The purpose of the current study was to evaluate the bonding performance of two single-liquid primers, which contained 6-(4-vinylbenzyl-n-propyl) amino-1,3,5-triazine-2,4-dithione (VTD) or 6-methacryloyloxyhexyl 2-thiouracil 5-carboxylate (MTU-6), used for bonding between metals and an acrylic resin. A gold alloy and high-purity titanium were used as adherend materials, and a transparent acrylic resin initiated with tri-n-butylborane derivative was selected as the luting material. Both adherends were treated with one of the primers and bonded with the luting material, after which shear bond strength was determined.

Effect of mechanochemical surface preparation on bonding to zirconia of a tri-n-butylborane initiated resin.

This study aimed to evaluate the effect of surface preparation on bond strength of a tri-n-butylborane initiated resin (MMA-TBB) bonded to zirconia. Zirconia disks were either airborne-particle abraded with alumina or silica-coated. The disks were thereafter primed with one of the following materials: phosphate-silane (Clearfil Ceramic Primer), phosphate (Alloy Primer), or silane (ESPE Sil).

Erratum to: 36th International Symposium on Intensive Care and Emergency Medicine: Brussels, Belgium. 15-18 March 2016.

[This corrects the article DOI: 10.1186/s13054-016-1208-6.].

Wear characteristics of polished and glazed lithium disilicate ceramics opposed to three ceramic materials.

This study compared the wear characteristics of a heat-pressed lithium disilicate ceramic material opposed to feldspathic porcelain, a lithium disilicate glass ceramic, and zirconia materials. Ceramic plate specimens were prepared from feldspathic porcelain (EX-3 nA1B), lithium disilicate glass ceramics (e.max CAD MO1/C14), and zirconia (Katana KT 10) and then ground or polished.