A "2-in-1" Bioanalytical System Based on Nanocomposite Conductive Polymers for Early Detection of Surface Water Pollution.

This work proposes an approach to the formation of receptor elements for the rapid diagnosis of the state of surface waters according to two indicators: the biochemical oxygen demand (BOD) index and toxicity. Associations among microorganisms based on the bacteria and yeast , as well as associations of the yeasts and , were formed to evaluate these indicators, respectively. The use of nanocomposite electrically conductive materials based on carbon nanotubes, biocompatible natural polymers-chitosan and bovine serum albumin cross-linked with ferrocenecarboxaldehyde, neutral red, safranin, and phenosafranin-has made it possible to expand the analytical capabilities of receptor systems.

Studies of Fractal Microstructure in Nanocarbon Polymer Composites.

The in situ study of fractal microstructure in nanocarbon polymers is an actual task for their application and for the improvement in their functional properties. This article presents a visualization of the bulk structural features of the composites using pulsed acoustic microscopy and synchrotron X-ray microtomography. This article presents details of fractal structure formation using carbon particles of different sizes and shapes-exfoliated graphite, carbon platelets and nanotubes.

Nanocomposites Based on Polyethylene and Nickel Ferrite: Preparation, Characterization, and Properties.

Composite materials based on NiFeO nanoparticles and polyethylene matrix have been synthesized by thermal decomposition to expand the application area of high-pressure polyethylene by filling it with nanoscale particles. The synthesized compositions were obtained in the form of a dark gray powder and compressed for further study According to TEM, the average particle size in composites was 2, 3, and 4 nm in samples with a filling of 10%, 20% and 30%. The concentration dependences of the specific electrical resistivity ρ, dielectric permittivity ε, saturation magnetization M and the parameters of reflection and attenuation of microwave power of the obtained composites were investigated.

Langmuir-Blodgett Films with Immobilized Glucose Oxidase Enzyme Molecules for Acoustic Glucose Sensor Application.

In this work, a sensitive coating based on Langmuir-Blodgett (LB) films containing monolayers of 1,2-dipalmitoyl-sn-glycero-3-phosphoethanolamine (DPPE) with an immobilized glucose oxidase (GOx) enzyme was created. The immobilization of the enzyme in the LB film occurred during the formation of the monolayer. The effect of the immobilization of GOx enzyme molecules on the surface properties of a Langmuir DPPE monolayer was investigated.

Langmuir-Blodgett Films of Arachidic and Stearic Acids as Sensitive Coatings for Chloroform HF SAW Sensors.

Properties of the Langmuir-Blodgett (LB) films of arachidic and stearic acids, versus the amount of the films' monolayers were studied and applied for chloroform vapor detection with acoustoelectric high-frequency SAW sensors, based on an AT quartz two-port Rayleigh type SAW resonator (414 MHz) and ST-X quartz SAW delay line (157.5 MHz). Using both devices, it was confirmed that the film with 17 monolayers of stearic acid deposited on the surface of the SAW delay line at a surface pressure of 30 mN/m in the solid phase has the best sensitivity towards chloroform vapors, compared with the same films with other numbers of monolayers.

Polymer Nanocomposite Containing Palladium Nanoparticles: Synthesis, Characterization, and Properties.

Composite nanomaterials have been prepared through thermal decomposition of palladium diacetate. The composite contains palladium nanoparticles embedded in high-pressure polyethylene. The materials were studied by a number of different physico-chemical methods, such as transmission electron microscopy, X-ray diffraction, X-ray absorption spectroscopy, electron paramagnetic resonance, and EXAFS.

-Based MFC with PEDOT:PSS/Graphene/Nafion Bioanode for Wastewater Treatment.

Microbial fuel cells (MFCs) are a variety of bioelectrocatalytic devices that utilize the metabolism of microorganisms to generate electric energy from organic matter. This study investigates the possibility of using a novel PEDOT:PSS/graphene/Nafion composite in combination with acetic acid bacteria to create a pure culture MFC capable of effective municipal wastewater treatment. The developed MFC was shown to maintain its activity for at least three weeks.

Radio-Absorbing Materials Based on Polymer Composites and Their Application to Solving the Problems of Electromagnetic Compatibility.

Recently, designers of electronic equipment have paid special attention to the issue of electromagnetic compatibility (EMC) of devices with their own components and assemblies. This is due to the high sensitivity of semiconductor microcircuits to electromagnetic interference. This interference can be caused either by natural phenomena, such as lightning strikes, or by technical processes, such as transients in circuits during fast periodic or random switching.

Modification of thermally expanded graphite and its effect on the properties of the amperometric biosensor.

The work considered the properties of a biosensor based on a novel nanomaterial-modified thermally expanded graphite (TEG). The main focus was on whether the procedure of additional graphite thermal expansion would affect the electrochemical properties of biosensors based on membrane fractions of acetic acid bacteria . Raman spectroscopy, scanning electron microscopy and electrochemical analysis were used for the study.

Impact of PN junction inhomogeneity on the piezoelectric fields of acoustic waves in piezo-semiconductive fibers.

Non-uniform mechanical strain can be easily induced at the interface of a piezoelectric semiconductive (PS) PN junction with variable cross sections by using piezoactive acoustic waves, and thus produces a giant piezoelectric field to significantly enhance the piezotronic effect. For revealing the piezotronic performance modulation in the non-uniform PS PN junction, the electromechanical field under a pair of applied end mechanical forces is studied from perspectives of theoretical analysis and numerical simulations. A one-dimensional linearized model for the PS fiber is established, which is applied for the mechanical analysis of a selected profile with the cross section varying in a specific quadratic function.

Morphology of Mixed Langmuir and Langmuir-Schaefer Monolayers with Covered CdSe/CdS/ZnS Quantum Dots and Arachidic Acid.

The process of formation of a Langmuir-Schaefer (LS) matrix based on a mixed monolayer of arachidic acid (AA) and 8 nm CdSe/CdS/ZnS quantum dots (QDs) stabilized by molecules of trioctylphosphine oxide (TOPO) was investigated. The change in the morphology, monolayer compressibility, and area per elementary cell of the created mixed monolayers, depending on the ratio of the components, was studied. It is shown that the change in the morphology of Langmuir-Blodgett (LB) monolayers begins to occur at a ratio between the number of QDs and AA molecules of 1:24.

The Peculiarities of the Acoustic Waves of Zero-Order Focusing in Lithium Niobate Plate.

In this research, beam focusing in lithium niobate plate was studied for fundamental anti-symmetric (A) and symmetric (S) Lamb waves, and the shear-horizontal (SH) wave of zero-order. Using the finite element method, appropriate configuration of the interdigital transducer with arc-like electrodes was modeled accounting for the anisotropy of the slowness curves and dispersion of the modes in the plate. Profiles of the focalized acoustic beams generated by the proposed transducer were theoretically analyzed.

An Analysis of the Water-to-Ice Phase Transition Using Acoustic Plate Waves.

It is shown that, in spite of the wave radiation into the adjacent liquid, a large group of Lamb waves are able to propagate along piezoelectric plates (quartz, LiNbO, LiTaO) coated with a liquid layer (distilled water HO). When the layer freezes, most of the group's waves increase their losses, essentially forming an acoustic response towards water-to-ice transformation. Partial contributions to the responses originating from wave propagation, electro-mechanical transduction, and wave scattering were estimated and compared with the coupling constants, and the vertical displacements of the waves were calculated numerically at the water-plate and ice-plate interfaces.

A Theoretical Model for Analyzing the Thickness-Shear Vibration of a Circular Quartz Crystal Plate With Multiple Concentric Ring Electrodes.

A dynamic model to analyze the thickness-shear vibration of a circular quartz crystal plate with multiple concentric ring electrodes on its upper and bottom surfaces is established with the aid of coordinate transformation. The theoretical solution is obtained, which can be written in a superposition form of Mathieu functions and modified Mathieu functions. The convergence of the solution is demonstrated, and the correctness is numerically validated via results from the finite element method (FEM).

Artificial Intelligence-Powered Search Tools and Resources in the Fight Against COVID-19.

Emerging technologies are set to play an important role in our response to the COVID-19 pandemic. This paper explores three prominent initiatives: COVID-19 focused datasets (e.g.

Inkjet Printing of Plate Acoustic Wave Devices.

In the paper, the results of production of Ag inkjet printed interdigital transducers to the acoustic delay line based on Y-cut X-propagation direction of lithium niobate plate for the frequency range from 1 to 14 MHz are presented. Additionally, morphological, structural, and electro-physical characteristics of the obtained electrodes were investigated. Mathematical modeling of the excitation of acoustic waves by these electrode structures was carried out.

Influence of Humidity on the Acoustic Properties of Mushroom Mycelium Films Used as Sensitive Layers for Acoustic Humidity Sensors.

The influence of humidity on the density, shear elastic module, viscosity, and thickness of the mushroom and mycelium films was studied. These data were obtained by comparing the theoretical and experimental frequency dependencies of the complex electrical impedance of bulk acoustic wave (BAW) resonator loaded by mycelium film using the least-squares method. This procedure was performed for the BAW resonator with pointed films for the relative humidity range of 17%-56% at the room temperature.

Influence of plate acoustic waves on electronic transport in nanowires.

The acoustoelectric effect is the generation of a acoustoelectric current in a non-biased device by a piezoactive acoustic wave. This effect has recently attracted the attention of researchers as a possible method to control the motion of massive objects in the quantum regime. We suggest using this effect for development of highly sensitive nanoelectronic sensors.

Multiwalled Carbon Nanotubes and the Electrocatalytic Activity of as the Basis of a Biosensor.

This paper considers the effect of multiwalled carbon nanotubes (MWCNTs) on the parameters of microbial biosensors. MWCNTs were shown not to affect the structural integrity of microbial cells and their respiratory activity. The positive results from using MWCNTs were due to a decrease in the impedance of the electrode.

Comparative Study of Electrochemical Sensors Based on Enzyme Immobilized into Polyelectrolyte Microcapsules and into Chitosan Gel.

The characteristics of an electrochemical biosensor based on a Prussian-blue screen-printed electrode containing glucose oxidase incorporated into polyelectrolyte microcapsules (PMC) are considered. PMC with the embedded enzyme were formed using sodium polystyrene sulfonate and poly(allylamine hydrochloride). The characteristics were compared with those of the enzyme immobilized in chitosan gel.

Bioelectrochemical Properties of Enzyme-Containing Multilayer Polyelectrolyte Microcapsules Modified with Multiwalled Carbon Nanotubes.

This work investigated changes in the biochemical parameters of multilayer membrane structures, emerging at their modification with multiwalled carbon nanotubes (MWCNTs). The structures were represented by polyelectrolyte microcapsules (PMCs) containing glucose oxidase (GOx). PMCs were made using sodium polystyrene sulfonate (polyanion) and poly(allylamine hydrochloride) (polycation).

Effects of Polymer Matrices and Carbon Nanotubes on the Generation of Electric Energy in a Microbial Fuel Cell.

The anode of a microbial fuel cell (MFC) was formed on a graphite electrode and immobilized VKM-1280 bacterial cells. Immobilization was performed in chitosan, poly(vinyl alcohol) or -vinylpyrrolidone-modified poly(vinyl alcohol). Ethanol was used as substrate.

Influence of electrical boundary conditions on profiles of acoustic field and electric potential of shear-horizontal acoustic waves in potassium niobate plates.

The profiles of an acoustic field and electric potential of the forward and backward shear-horizontal (SH) acoustic waves of a higher order propagating in X-Y potassium niobate plate have been theoretically investigated. It has been shown that by changing electrical boundary conditions on a surface of piezoelectric plates, it is possible to change the distributions of an acoustic field and electric potential of the forward and backward acoustic waves. The dependencies of the distribution of a mechanical displacement and electrical potential over the plate thickness for electrically open and electrically shorted plates have been plotted.

Super high sensitive plate acoustic wave humidity sensor based on graphene oxide film.

The changes of density and elastic modules due to water vapor adsorption are measured for graphene oxide film at room temperature. Dominant mechanism for acoustic wave humidity sensing by the film is shown to be related with variation of its electric conductivity. Basing on the data, super high sensitive humidity sensor employing high-order Lamb wave with large coupling constant, standard lithium niobate plate, and graphene oxide sorbent film is developed.

Solution-based electrical doping of semiconducting polymer films over a limited depth.

Solution-based electrical doping protocols may allow more versatility in the design of organic electronic devices; yet, controlling the diffusion of dopants in organic semiconductors and their stability has proven challenging. Here we present a solution-based approach for electrical p-doping of films of donor conjugated organic semiconductors and their blends with acceptors over a limited depth with a decay constant of 10-20 nm by post-process immersion into a polyoxometalate solution (phosphomolybdic acid, PMA) in nitromethane. PMA-doped films show increased electrical conductivity and work function, reduced solubility in the processing solvent, and improved photo-oxidative stability in air.