Cobalt ferrite nanoparticles supported on electrospun carbon fiber as a magnetic heterogeneous catalyst for activating peroxymonosulfate.

Cobalt ferrite (CF) nanoparticle (NP) represents a promising alternative to Co3O4 NP for peroxymonosulfate (PMS) activation in view of its strong magnetism for easy recovery. As CF NPs in water are prone to agglomerate, a few attempts have been made to immobilize CF NPs on substrates. While carbonaceous supports are more favorable owing to their earth abundancy, the study of carbon-supported CF for PMS activation is limited to graphene-based CF, which, however, requires complicated protocols to prepare.

Micro-structure and motion of two-dimensional dense short spherocylinder liquids.

We numerically investigate the micro-structure and motion of 2D liquids composed of dense short spherocylinders, by reducing the shape aspect ratio from 3. It is found that reducing shape aspect ratio from 3 causes a smooth transition from heterogeneous structures composed of crystalline ordered domains with good tetratic alignment order to those with good hexagonal bond-orientational order at an aspect ratio equaling 1.35.

Magnetic cobaltic nanoparticle-anchored carbon nanocomposite derived from cobalt-dipicolinic acid coordination polymer: An enhanced catalyst for environmental oxidative and reductive reactions.

Direct carbonization of cobalt complexes represents as a convenient approach to prepare magnetic carbon/cobalt nanocomposites (MCCNs) as heterogeneous environmental catalysts. However, most of MCCNs derived from consist of sheet-like carbon matrices with very sparse cobaltic nanoparticles (NPs), making them exhibit relatively low catalytic activities, porosity and magnetism. In this study, dipicolinic acid (DPA) is selected to prepare a 3-dimensional cobalt coordination polymer (CoDPA).

Ferrocene-modified chitosan as an efficient and green heterogeneous catalyst for sulfate-radical-based advanced oxidation process.

While ferrocene (Fc) is a promising heterogeneous catalyst for activating persulfate (PS) to degrade organic contaminants, chemical reagent-grade Fc is nanoscale and direct usage of Fc leads to operational and recovery issues. In this study, chitosan (CS) is selected as a support to immobilize Fc as CS is abundant, and environmental benign fishery waste. The amine group of CS also allows the formation of covalent bond between Fc-based reagent (i.

Ferrocene-functionalized graphitic carbon nitride as an enhanced heterogeneous catalyst of Fenton reaction for degradation of Rhodamine B under visible light irradiation.

To enhance degradation of Rhodamine B (RhB), a toxic xanthene dye, an iron-doped graphitic carbon nitride (CN) is prepared by establishing a covalent bond (-CN-) bridging ferrocene (Fc) and CN via a Schiff base reaction. The π-conjugation between the aromatic Fc and CN can be much enhanced by the covalent bond, thereby facilitating the bulk-to-surface charge transfer and separation as well as reversible photo-redox reactions during photocatalytic reactions. Thus, the resulting Fc-CN exhibits a much higher catalytic activity than CN to activate hydrogen peroxide (HP) for RhB degradation, because the photocatalytically generated electrons from CN can activate HP and effectively maintain the bivalence state of Fe in Fc, which also induces the activation of HP.

In-Situ Measurement of High-Temperature Proton Exchange Membrane Fuel Cell Stack Using Flexible Five-in-One Micro-Sensor.

In the chemical reaction that proceeds in a high-temperature proton exchange membrane fuel cell stack (HT-PEMFC stack), the internal local temperature, voltage, pressure, flow and current nonuniformity may cause poor membrane material durability and nonuniform fuel distribution, thus influencing the performance and lifetime of the fuel cell stack. In this paper micro-electro-mechanical systems (MEMS) are utilized to develop a high-temperature electrochemical environment-resistant five-in-one micro-sensor embedded in the cathode channel plate of an HT-PEMFC stack, and materials and process parameters are appropriately selected to protect the micro-sensor against failure or destruction during long-term operation. In-situ measurement of the local temperature, voltage, pressure, flow and current distributions in the HT-PEMFC stack is carried out.