Material efficiency at the component level: how much metal can we do without?

Global production of steel and aluminium is a major driver of greenhouse gas emissions. Various processes might allow continued primary production of the two metals, but all depend on emissions-free electricity or carbon storage, and global capacity of these two key resources will be below demand for decades to come. As a result, zero-emissions steel and aluminium will mainly come from recycling, but supply will be lower than demand.

Sustainable metals: integrating science and systems approaches.

This article introduces a special issue of the transactions arising from a Royal Society Discussion Meeting on 'sustainable metals'. Recognizing that progress to date toward the goals of 'sustainability' has been limited, the meeting aimed to open up a new level of interdisciplinary dialogue, collaboration and discussion of disruptive approaches. In this paper, the major concerns of sustainability are enumerated, and climate change is identified as the most urgent.

Electric recycling of Portland cement at scale.

Cement production causes 7.5% of global anthropogenic CO emissions, arising from limestone decarbonation and fossil-fuel combustion. Current decarbonation strategies include substituting Portland clinker with supplementary materials, but these mainly arise in emitting processes, developing alternative binders but none yet promises scale, or adopting carbon capture and storage that still releases some emissions.

What Contribution Could Industrial Symbiosis Make to Mitigating Industrial Greenhouse Gas (GHG) Emissions in Bulk Material Production?

In industrial symbiosis, byproducts and wastes are used to substitute other process inputs, with the goal of reducing the environmental impact of production. Potentially, such symbiosis could reduce greenhouse gas emissions; although there exists literature exploring this at specific industrial sites, there has not yet been a quantitative global assessment of the potential toward climate mitigation by industrial symbiosis in bulk material production of steel, cement, paper, and aluminum. A model based on physical production recipes is developed to estimate global mass flows for production of these materials with increasing levels of symbiosis.

Material Flow Analysis with Multiple Material Characteristics to Assess the Potential for Flat Steel Prompt Scrap Prevention and Diversion without Remelting.

Thirty-two percent of the liquid metal used to make flat steel products in Europe does not end up in a final product. Sixty percent of this material is instead scrapped during manufacturing and the remainder during fabrication of finished steel products. Although this scrap is collected and recycled, remelting this scrap requires approximately 2 MWh/t, but some of this material could instead be diverted for use in other applications without remelting.

The carbon price: a toothless tool for material efficiency?

This article explores whether a carbon price will effectively encourage the more efficient use of greenhouse gas intensive materials such as steel. The article identifies a range of distortions that arise when some of the restrictive assumptions of neoclassical economics are relaxed. Distortions occur due to the sequential nature of decision-making along supply chains, due to imperfect competition and due to government intervention to reduce the risk of carbon leakage.

The impact of reducing car weight on global emissions: the future fleet in Great Britain.

Current European policies define targets for future direct emissions of new car sales that foster a fast transition to electric drivetrain technologies. However, these targets do not consider the emissions produced in electricity generation and material production, and therefore fail to incentivise car manufacturers to consider the benefits of vehicle weight reduction. In this paper, we examine the potential benefits of limiting the average weight and altering the material composition of new cars in terms of global greenhouse gas emissions produced during the use phase, electricity generation and material production.

Industry 1.61803: the transition to an industry with reduced material demand fit for a low carbon future.

Arising from a discussion meeting in September 2016, this editorial introduces a special issue on the transition to a future industrial system with greatly reduced demand for material production and attempts to synthesize the main findings. The motivation for such a transition is to reduce industrial greenhouse gas emissions, but unlike previous industrial transformations, there are no major stakeholders who will pursue the change for their own immediate benefit. The special issue, therefore, explores the means by which such a transition could be brought about.

How Will Copper Contamination Constrain Future Global Steel Recycling?

Copper in steel causes metallurgical problems, but is pervasive in end-of-life scrap and cannot currently be removed commercially once in the melt. Contamination can be managed to an extent by globally trading scrap for use in tolerant applications and dilution with primary iron sources. However, the viability of long-term strategies can only be evaluated with a complete characterization of copper in the global steel system and this is presented in this paper.

Material Stock Demographics: Cars in Great Britain.

Recent literature on material flow analysis has been focused on quantitative characterization of past material flows. Fewer analyses exist on past and prospective quantification of stocks of materials in-use. Some of these analyses explore the composition of products' stocks, but a focus on the characterization of material stocks and its relation with service delivery is often neglected.

Utilization of structural steel in buildings.

Over one-quarter of steel produced annually is used in the construction of buildings. Making this steel causes carbon dioxide emissions, which climate change experts recommend be reduced by half in the next 37 years. One option to achieve this is to design and build more efficiently, still delivering the same service from buildings but using less steel to do so.

An integrated representation of the services provided by global water resources.

Water is essential not only to maintain the livelihoods of human beings but also to sustain ecosystems. Over the last few decades several global assessments have reviewed current and future uses of water, and have offered potential solutions to a possible water crisis. However, these have tended to focus on water supply rather than on the range of demands for all water services (including those of ecosystems).

Designing climate change mitigation plans that add up.

Mitigation plans to combat climate change depend on the combined implementation of many abatement options, but the options interact. Published anthropogenic emissions inventories are disaggregated by gas, sector, country, or final energy form. This allows the assessment of novel energy supply options, but is insufficient for understanding how options for efficiency and demand reduction interact.

The roles of energy and material efficiency in meeting steel industry CO2 targets.

Identifying strategies for reducing greenhouse gas emissions from steel production requires a comprehensive model of the sector but previous work has either failed to consider the whole supply chain or considered only a subset of possible abatement options. In this work, a global mass flow analysis is combined with process emissions intensities to allow forecasts of future steel sector emissions under all abatement options. Scenario analysis shows that global capacity for primary steel production is already near to a peak and that if sectoral emissions are to be reduced by 50% by 2050, the last required blast furnace will be built by 2020.

The steel scrap age.

Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions.

Mapping the global flow of aluminum: from liquid aluminum to end-use goods.

Demand for aluminum in final products has increased 30-fold since 1950 to 45 million tonnes per year, with forecasts predicting this exceptional growth to continue so that demand will reach 2-3 times today's levels by 2050. Aluminum production uses 3.5% of global electricity and causes 1% of global CO2 emissions, while meeting a 50% cut in emissions by 2050 against growing demand would require at least a 75% reduction in CO2 emissions per tonne of aluminum produced--a challenging prospect.

Material efficiency: providing material services with less material production.

Material efficiency, as discussed in this Meeting Issue, entails the pursuit of the technical strategies, business models, consumer preferences and policy instruments that would lead to a substantial reduction in the production of high-volume energy-intensive materials required to deliver human well-being. This paper, which introduces a Discussion Meeting Issue on the topic of material efficiency, aims to give an overview of current thinking on the topic, spanning environmental, engineering, economics, sociology and policy issues. The motivations for material efficiency include reducing energy demand, reducing the emissions and other environmental impacts of industry, and increasing national resource security.

The energy required to produce materials: constraints on energy-intensity improvements, parameters of demand.

In this paper, we review the energy requirements to make materials on a global scale by focusing on the five construction materials that dominate energy used in material production: steel, cement, paper, plastics and aluminium. We then estimate the possibility of reducing absolute material production energy by half, while doubling production from the present to 2050. The goal therefore is a 75 per cent reduction in energy intensity.

Transitions to material efficiency in the UK steel economy.

Steel production is energy intensive so already has achieved impressive levels of energy efficiency. If the emissions associated with steel must be reduced in line with the requirements of the UK Climate Change Act, demand for new steel must be reduced. The strategies of 'material efficiency' aim to achieve such a reduction, while delivering the same final services.

Product life trade-offs: what if products fail early?

Increasing product life allows the embodied emissions in products to be spread across a longer period but can mean that opportunities to improve use-phase efficiency are foregone. In this paper, a model that evaluates this trade-off is presented and used to estimate the optimal product life for a range of metal-intensive products. Two strategies that have potential to save emissions are explored: (1) adding extra embodied emissions to make products more sturdy, increasing product life, and (2) increasing frequency of use, causing early product failure to take advantage of improvements in use-phase efficiency.

Mapping the global flow of steel: from steelmaking to end-use goods.

Our society is addicted to steel. Global demand for steel has risen to 1.4 billion tonnes a year and is set to at least double by 2050, while the steel industry generates nearly a 10th of the world's energy related CO₂ emissions.

Reusing steel and aluminum components at end of product life.

Reusing steel and aluminum components would reduce the need for new production, possibly creating significant savings in carbon emissions. Currently, there is no clearly defined set of strategies or barriers to enable assessment of appropriate component reuse; neither is it possible to predict future levels of reuse. This work presents a global assessment of the potential for reusing steel and aluminum components.

Reducing energy demand: what are the practical limits?

Concern over the global energy system, whether driven by climate change, national security, or fears of shortage, is being discussed widely and in every arena but with a bias toward energy supply options. While demand reduction is often mentioned in passing, it is rarely a priority for implementation, whether through policy or through the search for innovation. This paper aims to draw attention to the opportunity for major reduction in energy demand, by presenting an analysis of how much of current global energy demand could be avoided.