Production of solid acid catalyst using waste cigarette filters for esterification.

Cigarette filters were utilized as carbon source for the production of solid carbon acid catalysts. In this study, the process of carbonization and simultaneous sulfonation via hydrothermal treatment was employed. The catalysts were prepared by mixing cigarette filters and sulfuric acid at temperatures of 100, 150, and 190 °C for durations ranging from 2 to 8 h.

Copper recovery through biohydrometallurgy route: chemical and physical characterization of magnetic (m), non-magnetic (nm) and mix samples from obsolete smartphones.

The more modern electronics are, the smaller and complex printed circuit boards are. Thus, these materials are continually changed (physicochemically), increasing the copper concentrations in smartphones. In this sense, it is challenging to set standardized recycling processes to improve metal recovery.

Copper and zinc adsorption from bacterial biomass - possibility of low-cost industrial wastewater treatment.

The increasing interest of all stakeholders to achieve environmental protection with socioeconomic development puts pressure on industrial processes for less negative impact on the environment. The use of biomass for wastewater treatment has increased due to its low costs and technical feasibility. The present study aimed the use of biomass from a waste of known polluted area for the adsorption of Zn and Cu in a fixed-bed reactor.

Electric car battery: An overview on global demand, recycling and future approaches towards sustainability.

Li-ion batteries are daily present in our electronic devices. These batteries are used in electric and hybrid vehicles supporting the current agreements to decrease greenhouse gas emissions. As a result, the electric vehicle demand has increased in the world.

Uranium removal from aqueous solution using macauba endocarp-derived biochar: Effect of physical activation.

The main aim of this study was to evaluate options for addressing two pressing challenges related to environmental quality and circular economy stemming from wastage or underutilization of abundant biomass residue resources and contamination of water by industrial effluents. In this study we focused on residues (endocarp) from Macaúba palm (Acrocomia aculeata) used for oil production, its conversion to activated biochar, and its potential use in uranium (U) removal from aqueous solutions. Batch adsorption experiments showed a much higher uranyl ions (U(VI)) removal efficiency of activated biochar compared to untreated biochar.

E-waste management and sustainability: a case study in Brazil.

The advancement of technology and development of new electronic and electrical equipment with a reduced life cycle has increased the need for the disposal of them (called Waste of Electric and Electronic Equipment or simply e-waste) due to defects presented during use, replacement of obsolete equipment, and ease of acquisition of new equipment. There is a lack of consumer awareness regarding the use, handling storage, and disposal of this equipment. In Brazil, the disposal of post-consumer waste is regulated by the National Solid Waste Policy, established by Law No.

Printed circuit board recycling: Physical processing and copper extraction by selective leaching.

Global generation of waste electrical and electronic equipment (WEEE) is about 40 million tons per year. Constant increase in WEEE generation added to international legislations has improved the development of processes for materials recovery and sustainability of electrical and electronic industry. This paper describes a new hydrometallurgical route (leaching process) to recycle printed circuit boards (PCBs) from printers to recover copper.

Printed wiring boards for mobile phones: characterization and recycling of copper.

The popularization of mobile phones, combined with a technological evolution, means a large number of scrap and obsolete equipment are discarded every year, thereby causing economic losses and environmental pollution. In the present study, the printed wiring boards scrap of mobile phones were characterized in order to recycle some of the device components, using techniques of mechanical processing, hydrometallurgy and electrometallurgy. The use of the techniques of mechanical processing (milling, particle size classification, magnetic and electrostatic separation) was an efficient alternative to obtain a concentrated fraction (mainly iron in the magnetic fraction and copper in the conductive fraction) and another fraction containing polymers and ceramics.

Recycling of WEEE: characterization of spent printed circuit boards from mobile phones and computers.

This paper presents a comparison between printed circuit boards from computers and mobile phones. Since printed circuits boards are becoming more complex and smaller, the amount of materials is constantly changing. The main objective of this work was to characterize spent printed circuit boards from computers and mobile phones applying mineral processing technique to separate the metal, ceramic, and polymer fractions.

Metal separation from mixed types of batteries using selective precipitation and liquid-liquid extraction techniques.

The purpose of this paper is to study metal separation from a sample composed of a mixture of the main types of spent household batteries, using a hydrometallurgical route, comparing selective precipitation and liquid-liquid extraction separation techniques. The preparation of the solution consisted of: grinding the waste of mixed batteries, reduction and volatile metals elimination using electric furnace and acid leaching. From this solution two different routes were studied: selective precipitation with sodium hydroxide and liquid-liquid extraction using Cyanex 272 [bis(2,4,4-trimethylpentyl) phosphoric acid] as extracting agent.

Electronic scraps--recovering of valuable materials from parallel wire cables.

Every year, the number of discarded electro-electronic products is increasing. For this reason recycling is needed, to avoid wasting non-renewable natural resources. The objective of this work is to study the recycling of materials from parallel wire cable through unit operations of mineral processing.

Recovery of copper from printed circuit boards scraps by mechanical processing and electrometallurgy.

The constant growth in generation of solid wastes stimulates studies of recycling processes. The electronic scrap is part of this universe of obsolete and/or defective materials that need to be disposed of more appropriately, or then recycled. In this work, printed circuit boards, that are part of electronic scrap and are found in almost all electro-electronic equipments, were studied.