Application of MOX Sensors to Determine the Emission of Volatile Compounds in Corn Groats as a Function of Vertical Pressure in the Silo and Moisture Content of the Bed.

This study was focused on the analysis of the emission of volatile compounds as an indicator of changes in the quality degradation of corn groats with 14% and 17% moisture content (wet basis) using an electronic nose (Agrinose) at changing vertical pressure values. The corn groats were used in this study in an unconsolidated state of 0 kPa (the upper free layer of bulk material in the silo) and under a consolidation pressure of 40 kPa (approximately 3 m from the upper layer towards the bottom of the silo) and 80 kPa (approximately 6 m from the upper layer towards the bottom of the silo). The consolidation pressures corresponded to the vertical pressures acting on the layers of the bulk material bed in medium-slender and low silos.

Determination of the Strength of Consolidated Powder Materials with a Pull-Based Tester.

In recent years, there has been increasing interest in the agglomeration of bulk materials. New methods are being sought to improve the measurement of bulkiness in food powders. This study aimed to design a new measuring device to assess the phenomenon of caking as well as the degree of strength of free-flowing powders.

Converging orifice used to control the discharge rate of spherical particles from a flat floor silo.

The effect of the converging orifice geometry in a model silo on the discharge rate of monosized spherical particles was studied experimentally and numerically. The cylindrical container was equipped with interchangeable inserts with converging discharge orifices of various upper diameters in the upper base and a constant lower diameter in the lower base. Plastic PLA beads and agricultural granular materials: wheat, rapeseeds, and linseeds were tested.

Breakage Strength of Wood Sawdust Pellets: Measurements and Modelling.

Wood pellets are an important source of renewable energy. Their mechanical strength is a crucial property. In this study, the tensile strength of pellets made from oak, pine, and birch sawdust with moisture contents of 8% and 20% compacted at 60 and 120 MPa was determined in a diametral compression test.

Mechanical and Combustion Properties of Agglomerates of Wood of Popular Eastern European Species.

The objective of the reported project was to produce wood agglomerates from popular East European species to determine their strength and combustion properties. Closed-die pellets were produced from sawdust of six types of wood common on the East European market: pine, willow, oak, poplar, birch, and beech. The properties of pellets, determined by the type of wood, were influenced by the compaction pressure and the moisture content of the sawdust.

Friction and Shear Properties of Pine Biomass and Pellets.

Knowledge on the mechanical properties of granular biomass is important for the design and efficient operation of equipment used for handling, storage, and processing. Their mechanical properties are used as a measure of material quality. In this study, the mechanical properties of granular biomass obtained from pines (sawdust, shavings, long shavings, and pellets) were determined under a moisture content range of 10-50%.

Discrete Element Method Modelling of the Diametral Compression of Starch Agglomerates.

Starch agglomerates are widely applied in the pharmaceutical, agricultural, and food industries. The formation of potato starch tablets and their diametral compression were simulated numerically and verified in a laboratory experiment to analyse the microscopic mechanisms of the compaction and the origins of their breakage strength. Discrete element method (DEM) simulations were performed using EDEM software.

Structural and Micromechanical Properties of Ternary Granular Packings: Effect of Particle Size Ratio and Number Fraction of Particle Size Classes.

The confined uniaxial tests of packings with discrete particle size distribution (PSD) were modeled with the discrete element method. Ternary packings of spheres with PSD uniform or nonuniform by number of particles were examined in three-dimensional (3D) system. The study addressed an effect of the particle size ratio and the particle size fraction on structural and micromechanical properties of mixtures.