Comparison of Mg/Ca concentration series from Patella depressa limpet shells using CF-LIBS and LA-ICP-MS.

The elemental composition of marine mollusk shells can offer valuable information about environmental conditions experienced by a mollusk during its lifespan. Previous studies have shown significant correlations between Mg/Ca concentration ratios measured on biogenic carbonate of mollusk shells and sea surface temperature (SST). Here we propose the use of Laser-Induced Breakdown Spectroscopy (LIBS) and the validation of the Calibration-Free LIBS (CF-LIBS) approach for the rapid measurement and estimation of Mg/Ca molar concentration profiles within Patella depressa Pennant, 1777 limpet shells.

A Microwave Polarimeter Demonstrator for Astronomy with Near-Infra-Red Up-Conversion for Optical Correlation and Detection.

This paper presents a 10 to 20 GHz bandwidth microwave polarimeter demonstrator, based on the implementation of a near-infra-red frequency up-conversion stage that allows both the optical correlation, when operating as a synthesized-image interferometer, and signal detection, when operating as a direct-image instrument. The proposed idea is oriented towards the implementation of ultra-sensitive instruments presenting several dozens or even thousands of microwave receivers operating in the lowest bands of the cosmic microwave background. In this work, an electro-optical back-end module replaces the usual microwave detection stage with Mach-Zehnder modulators for the frequency up-conversion, and an optical stage for the signals correlation and detection at near-infra-red wavelengths (1550 nm).

Proposal of Brillouin optical frequency-domain reflectometry (BOFDR).

We demonstrate a Brillouin optical frequency-domain reflectometry (BOFDR) technique, which can measure the strain and/or temperature along an optical fiber with one-end access, by detecting the spontaneous Brillouin scattering from a sinusoidally modulated pump light. Compared to the Brillouin optical frequency-domain analysis (BOFDA), we show that BOFDR measurements are free from the distorting components related to acoustic wave modulation, thus simplifying data processing.

Feasibility study of imaging spectroscopy to monitor the quality of online welding.

An online welding quality system based on the use of imaging spectroscopy is proposed and discussed. Plasma optical spectroscopy has already been successfully applied in this context by establishing a direct correlation between some spectroscopic parameters, e.g.

Defect Detection in Arc-Welding Processes by Means of the Line-to-Continuum Method and Feature Selection.

Plasma optical spectroscopy is widely employed in on-line welding diagnostics. The determination of the plasma electron temperature, which is typically selected as the output monitoring parameter, implies the identification of the atomic emission lines. As a consequence, additional processing stages are required with a direct impact on the real time performance of the technique.

Use of the Plasma Spectrum RMS Signal for Arc-Welding Diagnostics.

A new spectroscopic parameter is used in this paper for on-line arc-welding quality monitoring. Plasma spectroscopy applied to welding diagnostics has typically relied on the estimation of the plasma electronic temperature, as there is a known correlation between this parameter and the quality of the seams. However, the practical use of this parameter gives rise to some uncertainties that could provoke ambiguous results.

Arc-Welding Spectroscopic Monitoring based on Feature Selection and Neural Networks.

A new spectral processing technique designed for application in the on-line detection and classification of arc-welding defects is presented in this paper. A noninvasive fiber sensor embedded within a TIG torch collects the plasma radiation originated during the welding process. The spectral information is then processed in two consecutive stages.

Embedded spectroscopic fiber sensor for on-line arc-welding analysis.

A new fiber sensor system designed for spectroscopic analysis and on-line quality assurance of arc-welding processes is presented here. Although several different approaches have been considered for the optical capture of plasma emission in arc-welding processes, they tend to be invasive and make use of optical devices such as collimators or photodiodes. The solution proposed here is based on the arrangement of an optical fiber, which is used at the same time as the optical capturing device and also to deliver the optical information to a spectrometer, embedded within an arc-welding torch.