Mechanical Properties of P91 Steel (X10CrMoVNb9-1) during Simulated Operation in a Hydrogen-Containing Environment.

P91 steel (X10CrMoVNb9-1) is widely used in the energy industry. It is characterized by good mechanical properties, creep resistance, corrosion resistance, impact toughness, and resistance to thermal fatigue. Due to their operating conditions and martensitic structure, components made from P91 steel are often subject to damage related to the presence of hydrogen.

The Influence of MSR-B Mg Alloy Surface Preparation on Bonding Properties.

Nowadays, industrial adhesives are replacing conventional bonding methods in many industries, including the automotive, aviation, and power industries, among others. The continuous development of joining technology has promoted adhesive bonding as one of the basic methods of joining metal materials. This article presents the influence of surface preparation of magnesium alloys on the strength properties of a single-lap adhesive joint using a one-component epoxy adhesive.

High-Temperature Corrosion of Flame-Sprayed Power Boiler Components with Nickel Alloy Powders.

The development trends in the energy sector clearly indicate an increase in the share of biomass and alternative fuels fed for combustion in power boilers, which results in the imposition of many unfavourable factors and a demanding working environment. During the operation of the energy system, this means a sharp increase in corrosion of the gas-tight pipe walls and coils by the destructive action of chlorine and sulphur. Implementing advanced surface protection in addition to the selection of materials of better quality and resistance to difficult working conditions would significantly reduce their wear by high temperature corrosion.

The Phenomena and Criteria Determining the Cracking Susceptibility of Repair Padding Welds of the Inconel 713C Nickel Alloy.

The creep-resistant casting nickel alloys (e.g., Inconel 713C) belong to the group of difficult-to-weld materials that are using for precise element production; e.

Regeneration of Aluminum Matrix Composite Reinforced by SiC and GC Using Gas Tungsten Arc Welding Technology.

The main motivation behind the presented research was the regeneration of the damaged surface of composite materials. The testing of melting and pad welding of the composite surface by Gas Tungsten Arc Welding (GTAW) with alternating current (AC) were carried out. The material of investigation was an AlSi12/SiCp + GCsf hybrid composite made by a centrifugal casting process.

Hybrid Welding (Laser-Electric Arc MAG) of High Yield Point Steel S960QL.

The article discusses the effect of the hybrid-welding process (laser-electric arc MAG ) on the structure and properties of butt joints (having various thicknesses, i.e., 5 mm and 7 mm) made of steel S960QL.

Structural, physicochemical and biological properties of spray-dried wine powders.

Different fruit wines, chokeberry, blackcurrant and blueberry, were spray-dried using hydroxypropyl-β-cyclodextrin (HP-β-CD) and inulin (IN). The structural, physicochemical, and biological properties of the spray-dried wine powders were studied over 12months of storage in darkness at 8°C. Identification and quantification of single phenolic compounds before and after storage revealed that HP-β-CD had a positive effect on anthocyanin retention during storage for all microcapsules tested.

Microencapsulation of Nigella sativa oleoresin by spray drying for food and nutraceutical applications.

Oleoresin of Nigella sativa L. (Black cumin) was obtained from the seeds using hexane extraction at room temperature. The oleoresin was emulsified in an aqueous solution containing gum Arabic/maltodextrin (1:1 w/w) and then encapsulated in powder form by spray drying.

Odor active compounds content in spices and their microencapsulated powders measured by SPME.

Within this study, main odorants of marjoram and thyme (linalool and thymol) were determined in spices and microencapsulated powders using solid-phase microextraction (SPME). Analyses were conducted on selected batches of spices before and after decontamination and on microencapsulated powders prepared for technological purposes (improvement of aroma in decontaminated spices). Conditions of SPME analyses were determined for individual compounds and matrices.