The Effect of Acrylic Surface Preparation on Bonding Denture Teeth to Cellulose Fiber-Reinforced Denture Base Acrylic.

Patients who require dental prosthetic restoration using frame dentures in the front part of the mouth very frequently report that teeth fall out of their dentures. However, the available scientific papers are insufficient to compare the various methods of improving the connection between the denture base and the artificial tooth and choosing the best solution. This paper focuses on providing all parameters, enabling the reproduction of tests, and accounting for all variables.

Bonding and Strengthening the PLA Biopolymer in Multi-Material Additive Manufacturing.

3D printing is a revolutionary additive manufacturing method that enables rapid prototyping and design flexibility. A variety of thermoplastic polymers can be used in printing. As it is necessary to reduce the consumption of petrochemical resources, alternative solutions are being researched, and the interest in using bioplastics and biocomposites is constantly growing.

Assessment of the deformation model of the proximal tibia in the course of degenerative disease: analysis of the 3-dimensional mathematical model.

Background: The high tibial osteotomy (HTO) is an effective knee-saving procedure, which relieves arthritis symptoms and prolongs the life of the knee joint. This procedure requires detailed preoperative planning. Usually, the contralateral side is used as a template for this purpose.

The Influence of the Depth of Grinding on the Condition of the Surface Layer of 20MnCr5 Steel Ground with the Minimum Quantity Lubrication (MQL) Method.

This paper describes the research on abrasive machining conditions and their influence on microhardness and residual stresses distribution in the technological surface layer of 20MnCr5 steel. The roughness of ground samples was also measured. Samples underwent a vacuum carburizing process (LPC) followed by high-pressure gas quenching (HPGQ) in a 4D quenching chamber.

Influence of Resin Cement Thickness and Elastic Modulus on the Stress Distribution of Zirconium Dioxide Inlay-Bridge: 3D Finite Element Analysis.

The mechanical properties and the thickness of the resin cement agents used for bonding inlay bridges can modify the clinical performance of the restoration such as debonding or prosthetic materials fracture. Thus, the aim of this study was to evaluate the stress distribution and the maximum strain generated by resin cements with different elastic moduli and thicknesses used to cement resin-bonded fixed partial denture (RBFPD). A three-dimensional (3D) finite element analysis (FEA) was used, and a 3D model was created based on a Cone-Beam Computed Tomography system (CBCT).

The Influence of 3D Printing Parameters on Adhesion between Polylactic Acid (PLA) and Thermoplastic Polyurethane (TPU).

A 3D printer in FDM technology allows printing with two nozzles, which creates an opportunity to produce multi-material elements. Printing from two materials requires special consideration of the interface zone generated between their geometrical boundaries. This article aims to present the possibility of printing with PLA and TPU using commercially available filaments and software to obtain the best possible bond strength between two different polymers with respect to printing parameters, surface pattern (due to the material contact surface's roughness), and the order of layer application.

Assessment of morphological differences of the proximal tibia in healthy knees: analysis of the 3-dimensional mathematical model.

Background: High tibial osteotomy and many orthopedic surgical procedures around the knee joint requires precise preoperative planning. In-depth knowledge of the tibial plateau morphology is necessary to limit intraoperative complications like lateral hinge fracture. No studies were exploring the differences in proximal tibia surface geometry, in regards to gender and laterality, using a mathematical model.

Numerical Analysis of the Bond Strength between Two Methacrylic Polymers by Surface Modification.

The creation of acrylic dentures involves many stages. One of them is to prepare the surfaces of artificial teeth for connection with the denture plates. The teeth could be rubbed with a chemical reagent, the surface could be developed, or retention hooks could be created.

Chemical Modification of Cellulose Microfibres to Reinforce Poly(methyl methacrylate) Used for Dental Application.

The mechanical properties of dental acrylic resins have to be improved in the case of a thin denture plate. This can be achieved by cellulose addition, playing the role of active filler. But to provide the excellent dispersion of cellulose microfibres within the hydrophobic polymer matrix, its surface has to be modified.

A Study of Second-Phase Precipitates and Dispersoid Particles in 2024 Aluminum Alloy after Different Aging Treatments.

Aluminum alloys such as AA2024 are popular in the automotive and aircraft industries. The application of artificial aging significantly improves their mechanical properties by precipitation hardening. However, commercial alloys very often contain different amounts of elements such as Si and Fe that make the evolution of the microstructure harder to control.

Glutathione S-transferase pi as a target for tricyclic antidepressants in human brain.

GST pi, the main glutathione S-transferase isoform present in the human brain, was isolated from various regions of the brain and the in vitro effect of tricyclic antidepressants on its activity was studied. The results indicated that amitripyline and doxepin--derivatives of dibenzcycloheptadiene, as well as imipramine and clomipramine--derivatives of dibenzazepine, inhibit the activity of GST pi from frontal and parietal cortex, hippocampus and brain stem. All these tricyclics are noncompetitive inhibitors of the enzyme with respect to reduced glutathione and noncompetitive (amitripyline, doxepin) or uncompetitive (imipramine, clomipramine) with respect to the electrophilic substrate.