Effect of combining aminomethacrylate and fluoride against erosive and abrasive challenges on enamel and dentin.

This study evaluated the effect of solutions containing aminomethacrylate copolymer (AA) and sodium fluoride (F; 225 ppm F) or fluoride plus stannous chloride (FSn; 225 ppm F, 800 ppm Sn) against enamel and dentin erosion/abrasion. Solutions F, FSn, AA, F+AA, FSn+AA, and deionized water as negative control were tested. Bovine enamel and dentin specimens (n = 13/solution/substrate) underwent a set of erosion-abrasion cycles (0.

Exploring the functionalization of Ti-6Al-4V alloy with the novel antimicrobial peptide JIChis-2 via plasma polymerization.

This study aimed to characterize the immobilization of the novel JIChis-2 peptide on the Ti-6Al-4V alloy, widely used in the biomedical sector. The antimicrobial activity of JIChis-2 was evaluated in the Gram-negative bacterium . Its immobilization occurred by inducing the formation of covalent bonds between the N-terminus of the peptides and the surface previously submitted to acrylic acid polymerization the PECVD technique.

Film-Forming Polymers for Tooth Erosion Prevention.

Different agents have been proposed to prevent the progression of acid induced dental substance losses, which are called erosive tooth wear (ETW), such as fluorides, calcium, and phosphate-based products; however, there is a need for a further increase in efficacy. Recently, the ability of polymers to interact with the tooth surface, forming acid resistant films, has come into the focus of research; nevertheless, there is still the need for a better understanding of their mode of action. Thus, this article provides an overview of the chemical structure of polymers, their mode of action, as well as the effect of their incorporation into oral care products, acid beverages, and antacid formulations, targeting the prevention of ETW.

In-vitro evaluation of the anti-cariogenic effect of a hybrid coating associated with encapsulated sodium fluoride and stannous chloride in nanoclays on enamel.

Objective: The aim of this study is to test, in vitro, the anti-cariogenic effect of experimental hybrid coatings, with nano clays of halloysite or bentonite, loaded with sodium fluoride or with a combination of sodium fluoride and stannous chloride, respectively.

Methodology: The varnish Fluor Protector (1,000 ppm of F-) was used as positive control and no treatment was the negative control. Enamel specimens (5 mm × 5 mm) were obtained from bovine teeth.

Erosive tooth wear inhibition by hybrid coatings with encapsulated fluoride and stannous ions.

This study aimed to formulate a hybrid coating material (HC) and to modify this HC with fluoride (NaF) and stannous (SnCl) ions, directly or encapsulated in nano containers, testing the effects of these materials against dental erosion and erosion-abrasion. Enamel and dentin specimens were treated with the HCs, and then tested in erosion or erosion-abrasion cycling models of 5 days (n = 10 for each substrate, for each model). Deionized water was the negative control, and a fluoride varnish, the positive control.

Protective Effect of Solutions Containing Polymers Associated with Fluoride and Stannous Chloride on Hydroxyapatite Dissolution.

This study investigated the protective effect of experimental solutions containing 4 polymers (polyoxirane, hydroxypropylmethylcellulose [HPMC], pectin, and an amino methacrylate copolymer [AMC]) in 2 concentrations (low and high) associated or not with sodium fluoride (F; 225 ppm F-) or sodium fluoride plus stannous chloride (FS; 800 ppm Sn2+) on the dissolution of hydroxyapatite crystals (HA). Deionized water was the control. The pretreated HA was added to a 0.

Protective effect of anti-erosive solutions enhanced by an aminomethacrylate copolymer.

Objective: To investigate if an aminomethacrylate copolymer (AMC) could potentiate the anti-erosive effect of solutions containing sodium fluoride -F (225 ppm F) and sodium fluoride associated to stannous chloride -FS (800 ppm Sn).

Methods: The experimental solutions (F, FS, AMC, AMC + F, AMC + FS, and deionized water-DW as negative control) were tested in the presence of acquired pellicle. Polished bovine enamel specimens (n = 13/group) were submitted to an erosion-rehardening cycle (2 h immersion in human saliva, 5 min in 0.

Enhancing the Anti-Erosive Properties of Fluoride and Stannous with the Polymer Carbopol.

This in vitro study investigated whether Carbopol 980 polymer could potentiate the anti-erosive effect of solutions containing sodium fluoride (F) and sodium fluoride associated with stannous chloride (FS). The dissolution of hydroxyapatite treated with the experimental solutions (F [500 ppm F-], F + Carbopol [0.1%], FS [500 ppm F- + 800 ppm Sn2+], FS + Carbopol) was evaluated.

Chemical and mechanical resistance of novel experimental hybrid coatings on dentin permeability.

This study aimed to evaluate the capacity of novel experimental hybrid coatings (HC) to reduce dentin permeability and to verify their resistance to erosive and abrasive challenges. Dentin disc specimens (1 mm thick) were treated with 0.5 M EDTA solution and randomly allocated into three experimental groups (n = 10): Control (Saliva); Concentrated Hybrid Coating (TEOS/GPTMS/Y-APS); and Diluted Hybrid Coating (1:3 ratio with distilled water).

Randomized in situ trial on the efficacy of Carbopol in enhancing fluoride / stannous anti-erosive properties.

Objective: To evaluate if the bioadhesive polymer (Carbopol 980) could potentiate the protective effect of sodium fluoride with stannous chloride (FS) solution on the control of enamel erosive wear.

Methods: Cylindrical bovine enamel specimens were polished and randomly allocated into three groups (n = 60): FS (500 ppm F +800 ppm Sn - positive control), FS + Carbopol (0.1% Carbopol), and ultrapure water (negative control).

Influence of bioadhesive polymers on the protective effect of fluoride against erosion.

Objective: This study investigated if the incorporation of the bioadhesive polymers Carbopol 980, Carboxymethyl cellulose (CMC), and Aristoflex AVC in a fluoridated solution (NaF-900ppm) would increase the solution's protective effect against enamel erosion.

Methods: Enamel specimens were submitted to a 5-day de-remineralization cycling model, consisting of 2min immersions in 0.3% citric acid (6x/day), 1min treatments with the polymers (associated or not with fluoride), and 60min storage in artificial saliva.