Mechanical methods for materials concentration of lithium iron phosphate (LFP) cells and product potential evaluation for recycling.

The production and sales of lithium-ion batteries (LIB) are rapidly expanding nowadays, causing a significant impact on the consumption of critical raw materials, such as lithium. Thus, developing and improving methods for the separation and recovery of materials from LIBs is necessary to ensure the supply of critical raw materials, as well as to meet the recycling targets set by some countries. This study evaluated and compared two mechanical routes to concentrate materials of LiFePO (LPF) cells.

c-Si PV module recycling: Analysis of the use of a mechanical pre-treatment to reduce the environmental impact of thermal treatment and enhance materials recovery.

The current increase in the use of photovoltaic (PV) energy demands the search for solutions to recycle end-of-life modules. This study evaluated the use of a mechanical pre-treatment in the thermal recycling of c-Si crystalline PV modules, which were submitted to recycling routes to separate and concentrate the materials of interest. The first route was constituted by only thermal treatment, and the second route was constituted by a mechanical pre-treatment to remove the polymers from the backsheet, and subsequent thermal treatment.

Composition and recycling of smartphones: A mini-review on gaps and opportunities.

After more than a decade since smartphones became consolidated in the market, many recycling solutions have been proposed to deal with them. To continue developing useful solutions and enable adjustment of routes, this mini-review aims to analyse the current research scenario, presenting relevant gaps, trends and opportunities. From a structured searching and screening procedure, a vast source of data was arranged and is available to extract useful information (43 studies on composition and 93 studies on recycling).

Separation and concentration of valuable and critical materials from wasted LEDs by physical processes.

The generation of wasted LEDs is expected to grow in the coming years, raising the challenge of recycling and recovering their valuable and critical materials. Due to the low concentration of these materials, the current recycling processes available for LEDs have a significant recovery limitation. This study proposes an innovative, clean and effective physical method to segregate the valuable and critical materials into different fractions while enhancing their concentration: particle size separation followed by electrostatic separation.

Precious and critical metals from wasted LED lamps: characterization and evaluation.

LED lamps already conquered the market of general lighting and are expected to generate a substantial stream of e-waste in the coming years. The challenge of recycling LED lamps have emerged, and it is essential to address both environmental and economic aspects to achieve a circular economy. LED lamps contain precious and critical metals, which can be found in electrical components and in the LED itself, making them a prospective waste for recycling initiatives.

Assessment of LED lamps components and materials for a recycling perspective.

LED lamps have already conquered the market of general lighting. This new product will generate a substantial flow of e-waste requiring studies for the correct management, especially concerning recycling alternatives. This study proposes a material characterization of all the tubular and bulb LED lamp components (carcass, LEDs, printed circuit board and LED module).

Neodymium as the main feature of permanent magnets from hard disk drives (HDDs).

As a way to manage neodymium-iron-boron (NdFeB) magnets wasted in end-of-life hard disk drives (HDDs), a waste characterization is needed prior to a recycling process. Due to their magnetic properties, NdFeB magnets are essential in technological applications nowadays, thus causing an increase in the industrial demand for rare earth metals. However, these metals have a short supply, since they are difficult to obtain from ores, creating a critical market.

Recycling WEEE: Extraction and concentration of silver from waste crystalline silicon photovoltaic modules.

Photovoltaic modules (or panels) are important power generators with limited lifespans. The modules contain known pollutants and valuable materials such as silicon, silver, copper, aluminum and glass. Thus, recycling such waste is of great importance.

Recycling WEEE: Polymer characterization and pyrolysis study for waste of crystalline silicon photovoltaic modules.

Photovoltaic (PV) modules contain both valuable and hazardous materials, which makes its recycling meaningful economically and environmentally. In general, the recycling of PV modules starts with the removal of the polymeric ethylene-vinyl acetate (EVA) resin using pyrolysis, which assists in the recovery of materials such as silicon, copper and silver. The pyrolysis implementation, however, needs improvement given its importance.

Photovoltaic solar panels of crystalline silicon: Characterization and separation.

Photovoltaic panels have a limited lifespan and estimates show large amounts of solar modules will be discarded as electronic waste in a near future. In order to retrieve important raw materials, reduce production costs and environmental impacts, recycling such devices is important. Initially, this article investigates which silicon photovoltaic module's components are recyclable through their characterization using X-ray fluorescence, X-ray diffraction, energy dispersion spectroscopy and atomic absorption spectroscopy.

Determination of the potential gold electrowinning from an ammoniacal thiosulphate solution applied to recycling of printed circuit board scraps.

The use of electrochemical techniques in the selective recovery of gold from a solution containing thiosulphate, ammonia, and copper, obtained from the leaching of printed circuit boards from mobile phones using ammoniacal thiosulphate, are shown in this work. First, cyclic voltammetry tests were performed to determine the potential of electrodeposition of gold and copper, and then, electrowinning tests at different potentials for checking the rates of recovery of these metals were performed. The results of the cyclic voltammetry show that copper deposition occurs at potentials more negative than -600 mV (Ag/AgCl), whereas the gold deposition can be performed at potentials more positives than -600 mV (Ag/AgCl).

Disassembly and characterization of liquid crystal screens.

The technology used in the manufacturing of televisions and monitors has been changing in recent years. Monitors with liquid crystal displays (LCD) emerged in the market with the aim of replacing cathode ray tube monitors. As a result, the disposal of this type of product, which is already very high, will increase.

Printed wiring boards for mobile phones: characterization and recycling of copper.

The popularization of mobile phones, combined with a technological evolution, means a large number of scrap and obsolete equipment are discarded every year, thereby causing economic losses and environmental pollution. In the present study, the printed wiring boards scrap of mobile phones were characterized in order to recycle some of the device components, using techniques of mechanical processing, hydrometallurgy and electrometallurgy. The use of the techniques of mechanical processing (milling, particle size classification, magnetic and electrostatic separation) was an efficient alternative to obtain a concentrated fraction (mainly iron in the magnetic fraction and copper in the conductive fraction) and another fraction containing polymers and ceramics.

Characterization and recovery of polymers from mobile phone scrap.

Electronic scrap is part of a universally wide range of obsolete, defective, or used materials that need to be disposed of or recycled in an ecologically friendly manner. The present study focused on the polymers present in mobile phone scrap. In mobile phones, polymers are found in frames and in printed circuit boards (PCBs).

Recovery of copper from printed circuit boards scraps by mechanical processing and electrometallurgy.

The constant growth in generation of solid wastes stimulates studies of recycling processes. The electronic scrap is part of this universe of obsolete and/or defective materials that need to be disposed of more appropriately, or then recycled. In this work, printed circuit boards, that are part of electronic scrap and are found in almost all electro-electronic equipments, were studied.

Association of Actinobacillus pleuropneumoniae capsular polysaccharide with virulence in pigs.

The capsular polysaccharide (CP) of Actinobacillus pleuropneumoniae is required for virulence of the bacteria in swine. However, a molecular investigation of whether the type or quantity of CP affects A. pleuropneumoniae virulence has not been reported.