Plaque-associated lipids in Alzheimer's diseased brain tissue visualized by nonlinear microscopy.

By simultaneous coherent anti-Stokes Raman scattering (CARS) and 2-photon fluorescence microscopy of Thioflavin-S stained Alzheimer´s diseased human brain tissues, we show evidence of lipid deposits co-localizing with fibrillar β-amyloid (Aβ) plaques. Two lipid morphologies can be observed; lamellar structures and coalescing macro-aggregates of sub-micron sizes to ~25 μm. No significant lipid deposits were observed in non-fibrillar, diffuse plaques identified by Aβ immuno-staining.

Imaging of lipids in microalgae with coherent anti-stokes Raman scattering microscopy.

Microalgae have great prospects as a sustainable resource of lipids for refinement into nutraceuticals and biodiesel, which increases the need for detailed insights into their intracellular lipid synthesis/storage mechanisms. As an alternative strategy to solvent- and label-based lipid quantification techniques, we introduce time-gated coherent anti-Stokes Raman scattering (CARS) microscopy for monitoring lipid contents in living algae, despite strong autofluorescence from the chloroplasts, at approximately picogram and subcellular levels by probing inherent molecular vibrations. Intracellular lipid droplet synthesis was followed in Phaeodactylum tricornutum algae grown under (1) light/nutrient-replete (control [Ctrl]), (2) light-limited (LL), and (3) nitrogen-starved (NS) conditions.

Bacterial cellulose modified with xyloglucan bearing the adhesion peptide RGD promotes endothelial cell adhesion and metabolism--a promising modification for vascular grafts.

Today, biomaterials such as polytetrafluorethylene (ePTFE) are used clinically as prosthetic grafts for vascular surgery of large vessels (>5 mm). In small diameter vessels, however, their performance is poor due to early thrombosis. Bacterial-derived cellulose (BC) is a new promising material as a replacement for blood vessels.

An in vitro study of blood compatibility of vascular grafts made of bacterial cellulose in comparison with conventionally-used graft materials.

In this study we analyzed the blood compatibility of bacterial cellulose (BC) as a new biosynthetic material for use as a vascular graft. As reference materials we used expanded polytetrafluoroethylene (ePTFE) and poly(ethylene terephthalate) (PET) vascular grafts. These materials are in clinical use today.

Real-time measurements of coagulation on bacterial cellulose and conventional vascular graft materials.

The search for a functional, small diameter (<5mm) vascular graft has been ongoing for over 30 years, but yet there is no consistently reliable synthetic graft. The primary mechanisms of graft failure are intimal hyperplasia, poor blood flow and surface thrombogenicity. Bacterial cellulose (BC) became therefore a proposed new biosynthetic vascular graft material.

Intravital fluorescent microscopic evaluation of bacterial cellulose as scaffold for vascular grafts.

Although commonly used synthetic vascular grafts perform satisfactorily in large caliber blood vessels, they are prone to thrombosis in small diameter vessels. Therefore, small vessels might benefit from tissue engineered vascular grafts. This study evaluated bacterial cellulose (BC) as a potential biomaterial for biosynthetic blood vessels.

Modification of nanocellulose with a xyloglucan-RGD conjugate enhances adhesion and proliferation of endothelial cells: implications for tissue engineering.

This paper describes a novel method for introducing the RGD cell adhesion peptide to enhance cell adhesion onto bacterial cellulose (BC). BC and cotton linters as reference were modified with xyloglucan (XG) and xyloglugan bearing a GRGDS pentapeptide. The adsorptions followed Langmuir adsorption behavior, where both XGs probably decorate the cellulose surfaces as a monolayer.

Influence of cultivation conditions on mechanical and morphological properties of bacterial cellulose tubes.

Bacterial cellulose (BC) was deposited in tubular form by fermenting Acetobacter xylinum on top of silicone tubes as an oxygenated support and by blowing different concentrations of oxygen, that is, 21% (air), 35%, 50%, and 100%. Mechanical properties such as burst pressure and tensile properties were evaluated for all tubes. The burst pressure of the tubes increased with an increase in oxygen ratio and reached a top value of 880 mmHg at 100% oxygen.