Carbon microspheres prepared from soluble starch hydrothermal carbonization for extending thermal stability of water-based drilling fluid.

This study employed hydrothermal carbon microspheres (HCMs) as high-temperature stabilizers in drilling fluids. The HCMs were synthesized through a green hydrothermal carbonization method, using soluble starch as the precursor. The impact of HCMs on the thermal stability of xanthan, polyanionic cellulose and synthetic polymer solutions was assessed by comparing their rheological changes before and after thermal aging.

Application of Psyllium Husk as a Friendly Filtrate Reducer for High-Temperature Water-Based Drilling Fluids.

Aiming at the challenge that environmental protection and high-temperature fluid loss reduction performance of the traditional water-based drilling fluid treatment agent are difficult to balance, our studies added psyllium husk as a high-temperature-resistant and environmentally friendly filtrate reducer to a water-based drilling fluid. The composition, physical and chemical properties, and microstructure of psyllium husk are characterized. Then, the effects of psyllium husk after hot rolling at different temperatures on the rheological properties and fluid loss properties of bentonite-based slurry are evaluated.

Novel Acrylamide/2-Acrylamide-2-3 Methylpropanesulfonic Acid/Styrene/Maleic Anhydride Polymer-Based CaCO Nanoparticles to Improve the Filtration of Water-Based Drilling Fluids at High Temperature.

Filtration loss control under high-temperature conditions is a worldwide issue among water-based drilling fluids (WBDFs). A core-shell high-temperature filter reducer (PAASM-CaCO) that combines organic macromolecules with inorganic nanomaterials was developed by combining acrylamide (AM), 2-acrylamide-2-methylpropane sulfonic acid (AMPS), styrene (St), and maleic anhydride (MA) as monomers and nano-calcium carbonate (NCC). The molecular structure of PAASM-CaCO was characterized.

Wellbore Stability through Novel Catechol-Chitosan Biopolymer Encapsulator-Based Drilling Mud.

The problem of wellbore stability has a marked impact on oil and gas exploration and development in the process of drilling. Marine mussel proteins can adhere and encapsulate firmly on deep-water rocks, providing inspiration for solving borehole stability problem and this ability comes from catechol groups. In this paper, a novel biopolymer was synthesized with chitosan and catechol (named "SDGB") by Schiff base-reduction reaction, was developed as an encapsulator in water-based drilling fluids (WBDF).

Intelligent Temperature-Control of Drilling Fluid in Natural Gas Hydrate Formation by Nano-Silica/Modified n-Alkane Microcapsules.

Inhibiting hydrate decomposition due to the friction heat generated by the drilling tools is one of the key factors for drilling hydrate formation. Since the existing method based on chemical inhibition technology can only delay the hydrate decomposition rate, a phase-change microcapsule was introduced in this paper to inhibit, by the intelligent control of the drilling fluid temperature, the decomposition of the formation hydrate, which was microencapsulated by modified n-alkane as the core material, and nano-silica was taken as the shell material. Scanning electron microscope (SEM), size distribution, X-ray diffraction (XRD), and Fourier transform infrared spectrometer (FT-IR) were utilized to characterize the structural properties of microcapsules.

Study of Environmentally Friendly Wild Jujube Pit Powder as a Water-Based Drilling Fluid Additive.

The development of offshore oil and gas requires environmental protection during the drilling process. However, the existing drilling fluid additives cannot form an efficient environmentally friendly drilling fluid system. At the same time, some environmentally friendly drilling fluid additives cannot be widely used due to their high cost and complicated production process.

Insight into β-cyclodextrin polymer microsphere as a potential filtration reducer in water-based drilling fluids for high temperature application.

Controlling the filtration of water-based drilling fluid effectively in high temperature environment is a great challenge in drilling engineering. In this study, β-cyclodextrin polymer microspheres (β-CDPMs) were synthesized by crosslinking between β-cyclodextrin and epichlorohydrin via inverse emulsion polymerization and employed as filtration reducers. The standard American Petroleum Institute filtration test showed that the β-CDPMs can only perform the enhanced filtration control ability at temperatures above 160 °C, and can tolerate the temperature resistance up to 240 °C without significant influence of rheology.

Nitrogen-containing switchable solvents for separation of hydrocarbons and their derivatives.

Solvent extraction is commonly used to separate mixtures of hydrocarbons and their derivatives, and solvent choice is strongly influenced by the affinity to the target component, cost and safety. Nitrogen-containing switchable solvents can switch from water-immiscible form to water-miscible bicarbonate salts when CO is injected and back to water-immiscible form when N is injected. Switchable solvents, as a type of recyclable green solvent, can be used not only to separate such mixtures but also to reduce process costs.

Characterization of bitumen and a novel multiple synergistic method for reducing bitumen viscosity with nanoparticles and surfactants.

This paper is concerned with the formation of bitumen during the drilling of the H oilfield in Iraq. The high viscosity and strong adhesion properties of bitumen can influence the drilling operations. Some complex problems include paste screening, and drill pipe sticking, which cause huge economic losses.

Bitumen Recovery from Crude Bitumen Samples from Halfaya Oilfield by Single and Composite Solvents-Process, Parameters, and Mechanism.

Since 2007, heterogeneous, high-viscosity active bituminous formations have often occurred during the drilling process in Yadavaran oilfield (Iran), Halfaya oilfield (Iraq), and tar sands (Canada). The formation of bitumen exhibits plastic and creep properties, and its adhesion is strong, so drilling accidents are easily caused, such as adhering vibrating screen, drill pipe sticking, lost circulation, and even well abandonment. These complex problems cause huge economic losses.

Mitigation of Lost Circulation in Oil-Based Drilling Fluids Using Oil Absorbent Polymers.

In order to mitigate the loss circulation of oil-based drilling fluids (OBDFs), an oil-absorbent polymer (OAP) composed by methylmethacrylate (MMA), butyl acrylate (BA), and hexadecyl methacrylate (HMA) was synthesized by suspension polymerization and characterized by Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA) and scanning electronic microscopy (SEM). The oil-absorptive capacity of OAP under different solvents was measured as the function of temperature and time. The effect of the OAP on the rheological and filtration properties of OBDFs was initially evaluated, and then the sealing property of OAP particles as lost circulation materials (LCMs) was examined by a high-temperature and high-pressure (HTHP) filtration test, a sand bed filtration test, a permeable plugging test, and a fracture sealing testing.

A polymer microsphere emulsion as a high-performance shale stabilizer for water-based drilling fluids.

Interest in using nanomaterials to improve shale stability during drilling operations has been increasing. Herein, a polymer microsphere emulsion (PME) as a high-performance shale stabilizer for water-based drilling fluids (WDFs) was prepared emulsion polymerization. The particle sizes in PME in aqueous solution ranged from 90 to 320 nm.

Thermo-sensitive polymer nanospheres as a smart plugging agent for shale gas drilling operations.

Emulsifier-free poly(methyl methacrylate-styrene) [P(MMA-St)] nanospheres with an average particle size of 100 nm were synthesized in an isopropyl alcohol-water medium by a solvothermal method. Then, through radical graft copolymerization of thermo-sensitive monomer -isopropylacrylamide (NIPAm) and hydrophilic monomer acrylic acid (AA) onto the surface of P(MMA-St) nanospheres at 80 °C, a series of thermo-sensitive polymer nanospheres, named SD-SEAL with different lower critical solution temperatures (LCST), were prepared by adjusting the mole ratio of NIPAm to AA. The products were characterized by Fourier transform infrared spectroscopy, transmission electron microscopy, thermogravimetric analysis, particle size distribution, and specific surface area analysis.