Insights into the Lithium Nucleation and Plating/Stripping Behavior in Ionic Liquid-Based Electrolytes.

Rechargeable lithium-metal batteries (LMBs) are anticipated to enable enhanced energy densities, which can be maximized when minimizing the amount of excess lithium in the cell down to zero, also referred to as "zero excess" LMBs. In this case, the only source of lithium is the positive electrode active material─just like in lithium-ion batteries. However, this requires the fully reversible deposition of metallic lithium, i.

Enabling High-Stability of Aqueous-Processed Nickel-Rich Positive Electrodes in Lithium Metal Batteries.

Lithium batteries occupy the large-scale electric mobility market raising concerns about the environmental impact of cell production, especially regarding the use of poly(vinylidene difluoride) (teratogenic) and N-methyl-2-pyrrolidone (NMP, harmful). To avoid their use, an aqueous electrode processing route is utilized in which a water-soluble hybrid acrylic-fluoropolymer together with sodium carboxymethyl cellulose is used as binder, and a thin phosphate coating layer is in situ formed on the surface of the nickel-rich cathode during electrode processing. The resulting electrodes achieve a comparable performance to that of NMP-based electrodes in conventional organic carbonate-based electrolyte (LP30).

Stabilizing the Li Al Ti (PO ) |Li Interface for High Efficiency and Long Lifespan Quasi-Solid-State Lithium Metal Batteries.

To tackle the poor chemical/electrochemical stability of Li Al Ti (PO ) (LATP) against Li and poor electrode|electrolyte interfacial contact, a thin poly[2,3-bis(2,2,6,6-tetramethylpiperidine-N-oxycarbonyl)norbornene] (PTNB) protection layer is applied with a small amount of ionic liquid electrolyte (ILE). This enables study of the impact of ILEs with modulated composition, such as 0.3 lithium bis(fluoromethanesulfonyl)imide (LiFSI)-0.

Quasi-Solid-State Lithium Metal Batteries Using the LiNiCoMnO-LiAlTi(PO) Composite Positive Electrode.

NASICON-type LiAlTi(PO) (LATP) is a promising solid electrolyte (SE) candidate for next-generation solid-state batteries. However, its use in solid-state composite electrodes is inhibited by its stiffness, which results in poor interparticle contact unless high-temperature treatments are applied. The poor LATP-LATP and LATP-active material in the positive electrode (cathode) composite produced at ambient temperature yield poor ionic conductivity, impeding the electrode's performance.

Organic Liquid Crystals as Single-Ion Li Conductors.

The development of new materials for tomorrow's electrochemical energy storage technologies, based on thoroughly designed molecular architectures is at the forefront of materials research. In this line, we report herein the development of a new class of organic lithium-ion battery electrolytes, thermotropic liquid crystalline single-ion conductors, for which the single-ion charge transport is decoupled from the molecular dynamics (i. e.

Influence of Carbonate-Based Additives on the Electrochemical Performance of Si NW Anodes Cycled in an Ionic Liquid Electrolyte.

Addition of electrolyte additives (ethylene or vinylene carbonate) is shown to dramatically improve the cycling stability and capacity retention (1600 mAh g) of Si nanowires (NWs) in a safe ionic liquid (IL) electrolyte (0.1LiTFSI-0.6PYRFSI-0.

Overcoming the Interfacial Limitations Imposed by the Solid-Solid Interface in Solid-State Batteries Using Ionic Liquid-Based Interlayers.

Li-garnets are promising inorganic ceramic solid electrolytes for lithium metal batteries, showing good electrochemical stability with Li anode. However, their brittle and stiff nature restricts their intimate contact with both the electrodes, hence presenting high interfacial resistance to the ionic mobility. To address this issue, a strategy employing ionic liquid electrolyte (ILE) thin interlayers at the electrodes/electrolyte interfaces is adopted, which helps overcome the barrier for ion transport.

A More Sustainable and Cheaper One-Pot Route for the Synthesis of Hydrophobic Ionic Liquids for Electrolyte Applications.

An innovative one-pot synthetic process that uses water as the only processing solvent was used to obtain ionic liquids (ILs) in a yield of approximately 95 mol % and purity greater than 99.3 wt % (<2 ppm each of lithium, bromide and moisture) in a processing time of 1 h. Since no heating is needed for carrying out the reaction and no purification through sorbents is required, energy, time and chemicals can be saved to minimize waste production.

Alloying Reaction Confinement Enables High-Capacity and Stable Anodes for Lithium-Ion Batteries.

The current insertion anode chemistries are approaching their capacity limits; thus, alloying reaction anode materials with high theoretical specific capacity are investigated as potential alternatives for lithium-ion batteries. However, their performance is far from being satisfactory because of the large volume change and severe capacity decay that occurs upon lithium alloying and dealloying processes. To address these problems, we propose and demonstrate a versatile strategy that makes use of the electronic reaction confinement the synthesis of ultrasmall Ge nanoparticles (10 nm) uniformly confined in a matrix of larger spherical carbon particles (Ge⊂C spheres).

Enhancing the Electrochemical Performance of LiNiCoMnO by VO/LiVO Coating.

Despite layered LiNiCoMnO having drawn much attention for their high capacity and high energy density, they still endure strong capacity decay upon prolonged cycling and high C-rates, primarily due to sluggish Li and charge-transfer kinetics and detrimental parasitic reactions with the electrolyte. To address these issues, application of a surface-coating layer made of VO/LiVO on LiNiCoMnO (V-NCM) is pursued. Benefiting from the ionic conductivity of LiVO and the electronic conductivity of VO, resulting in both enhanced Li diffusion and charge-transfer kinetics, the coated material offers significantly improved C-rate capability.

Ionic Liquid-Based Electrolyte Membranes for Medium-High Temperature Lithium Polymer Batteries.

Li⁺-conducting polyethylene oxide-based membranes incorporating -butyl--methylpyrrolidinium bis(trifluoromethanesulfonyl)imide are used as electrolyte separators for all-solid-state lithium polymer batteries operating at medium-high temperatures. The incorporation of the ionic liquid remarkably improves the thermal, ion-transport and interfacial properties of the polymer electrolyte, which, in combination with the wide electrochemical stability even at medium-high temperatures, allows high current rates without any appreciable lithium anode degradation. Battery tests carried out at 80 °C have shown excellent cycling performance and capacity retention, even at high rates, which are never tackled by ionic liquid-free polymer electrolytes.

Complementary Strategies Toward the Aqueous Processing of High-Voltage LiNi Mn O Lithium-Ion Cathodes.

Increasing the environmental benignity of lithium-ion batteries is one of the greatest challenges for their large-scale deployment. Toward this end, we present herein a strategy to enable the aqueous processing of high-voltage LiNi Mn O (LNMO) cathodes, which are considered highly, if not the most, promising for the realization of cobalt-free next-generation lithium-ion cathodes. Combining the addition of phosphoric acid with the cross-linking of sodium carboxymethyl cellulose by means of citric acid, aqueously processed electrodes with excellent performance are produced.

Behavior of Germanium and Silicon Nanowire Anodes with Ionic Liquid Electrolytes.

The electrochemical behavior of binder-free, germanium and silicon nanowires as high-capacity anode materials for lithium-ion battery systems is investigated in an ionic liquid electrolyte. Cyclic voltammetry, cycling tests, and impedance spectroscopy reveal a highly reversible lithium alloying/dealloying process, as well as promising compatibility between the Ge and Si materials and the electrolyte components. Reversible capacities of 1400 and 2200 mA h g are delivered by the Ge and Si anodes, respectively, matching the values exhibited in conventional organic solutions.

Study of Water-Based Lithium Titanate Electrode Processing: The Role of pH and Binder Molecular Structure.

This work elucidates the manufacturing of lithium titanate (Li₄Ti₅O, LTO) electrodes via the aqueous process using sodium carboxymethylcellulose (CMC), guar gum (GG) or pectin as binders. To avoid aluminum current collector dissolution due to the rising slurries' pH, phosphoric acid (PA) is used as a pH-modifier. The electrodes are characterized in terms of morphology, adhesion strength and electrochemical performance.

Macromol. Rapid Commun. 14/2016.

Back Cover: Quaternary polymer electrolytes, containing PEO, LiTFSI, ionic liquid and ceramic filler, show higher limiting current density, conductivity and improved cycling performance in lithium metal/solid polymer electrolyte/LiFePO4 cells with respect to ternary electrolytes with either ionic liquid or ceramic filler. Further details can be found in the article by V. Sharova, G.

A Lithium-Ion Battery with Enhanced Safety Prepared using an Environmentally Friendly Process.

A new lithium-ion battery chemistry is presented based on a conversion-alloying anode material, a carbon-coated Fe-doped ZnO (TMO-C), and a LiNi1/3 Mn1/3 Co1/3 O2 (NMC) cathode. Both electrodes were fabricated using an environmentally friendly cellulose-based binding agent. The performance of the new lithium-ion battery was evaluated with a conventional, carbonate-based electrolyte (ethylene carbonate:diethyl carbonate-1 m lithium hexafluorophosphate, EC:DEC 1 m LiPF6 ) and an ionic liquid (IL)-based electrolyte (N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide-0.

In Situ Coating of Li[Ni0.33 Mn0.33 Co0.33 ]O2 Particles to Enable Aqueous Electrode Processing.

The aqueous processing of lithium-ion battery (LIB) electrodes has the potential to notably decrease the battery processing costs and paves the way for a sustainable and environmentally benign production (and recycling) of electrochemical energy storage devices. Although this concept has already been adopted for the industrial production of LIB graphite anodes, the performance decay of cathode electrodes based on transition metal oxides processed in aqueous environments is still an open issue. In this study, we show that the addition of small quantities of phosphoric acid into the cathodic slurry yields Li[Ni0.

Quaternary Polymer Electrolytes Containing an Ionic Liquid and a Ceramic Filler.

In this work, the individual and combined effects of an ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide and ceramic filler silicon dioxide on the thermal and electrochemical properties of poly(ethylene oxide) electrolytes have been investigated. The electrolyte containing both components has the lowest glass transition (-60 °C) and melting temperatures (27 °C), the highest conductivity at any investigated temperature, and the highest limiting current density (at 40 °C). This solid polymer electrolyte also exhibits the best long-term cycling performance in Li/LiFePO4 cells.

High Temperature Stable Separator for Lithium Batteries Based on SiO₂ and Hydroxypropyl Guar Gum.

A novel membrane based on silicon dioxide (SiO₂) and hydroxypropyl guar gum (HPG) as binder is presented and tested as a separator for lithium-ion batteries. The separator is made with renewable and low cost materials and an environmentally friendly manufacturing processing using only water as solvent. The separator offers superior wettability and high electrolyte uptake due to the optimized porosity and the good affinity of SiO₂ and guar gum microstructure towards organic liquid electrolytes.

Electrochemical properties of Si film electrodes grown on current collectors with CuO nanostructures for thin-film microbatteries.

Si film electrodes were deposited onto Cu foil current collectors fabricated with well-formed CuO nanostructures. The structural and electrochemical properties of the Cu foils oxidized for 1, 3, and 6 h and of the Si film electrodes were investigated using field-emission scanning electron microscopy, X-ray diffraction (XRD), and charge/discharge tests. The morphologies and XRD profiles suggested that the oxidized Cu foils consisted of a top CuO layer and a bottom Cu2O layer.

Ionic liquid electrolytes for Li-air batteries: lithium metal cycling.

In this work, the electrochemical stability and lithium plating/stripping performance of N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (Pyr14TFSI) are reported, by investigating the behavior of Li metal electrodes in symmetrical Li/electrolyte/Li cells. Electrochemical impedance spectroscopy measurements and galvanostatic cycling at different temperatures are performed to analyze the influence of temperature on the stabilization of the solid electrolyte interphase (SEI), showing that TFSI-based ionic liquids (ILs) rank among the best candidates for long-lasting Li-air cells.