Influence of fabrication method on the marginal fit of temporary restorations.

Computer-aided manufacturing (CAM) technology allows the use of different manufacturing techniques. This in vitro study aimed to evaluate the marginal fit of temporary restorations manufactured using conventional chairside methods, milling, and three-dimensional printing. Fifteen 3-element temporary restorations specimens were produced and categorized into three groups: non-digital, obtained using the conventional chairside method (GC); milled (GM); and three-dimensionally printed (GP).

Accuracy of Conventional and 3D-Printed Casts for Partial Fixed Prostheses.

Purpose: To evaluate and compare the accuracy of conventional and 3D-printed casts using five different 3D printers.

Materials And Methods: In the control group (CG group, n = 5), five conventional impressions using light- and heavy-body polyvinyl siloxane were obtained from the master model, resulting in five stone models. In the test groups, five different scans were performed by a well-trained and experienced clinician using a TRIOS intraoral scanner.

Physical and mechanical properties of four 3D-printed resins at two different thick layers: An in vitro comparative study.

Objectives: This in vitro comparative study aimed to evaluate the physical and mechanical properties of four 3D-printed resins with two different thickness layers.

Methods: Four printed resins (VarseoSmile Crown Plus, VSC; NexDent C&B MFH, MFH; Nanolab 3D, NNL; and Resilab 3D Temp, RSL) were printed with 50 µm and 100 µm layer thickness, resulting in 80 bars measuring 25 × 2×2 mm. The specimens underwent a Raman spectroscopy for degree of conversion, confocal laser scanning microscopy for surface roughness (Sa), three-point bending test for flexural strength and elastic modulus, and a Vickers hardness test (VHN).

Cost and effectiveness of 3-dimensionally printed model using three different printing layer parameters and two resins.

Statement Of Problem: When 3-dimensional printing casts, the operator can change the type of resin and the printing layer thickness, reducing the fabrication time. However, how these parameters affect the accuracy of 3-dimensionally printed casts is unknown.

Purpose: The purpose of this in vitro study was to evaluate the accuracy of 3-dimensionally printed casts by using a stereolithography (SLA) 3-dimensional printer (Forms2) with 3 different layer thickness (25, 50, and 100 μm) and 2 different resins (Gray and Cast) and by comparing the time to obtain each cast.

A fully digital approach for implant fixed complete dentures: A case report.

Introductions: Intraoral scanner has been widely used for implant impression in partially edentulous cases; however, its accuracy in the impression of full-arch implant is still questionable.

Clinical Report: This clinical report presents a technique to check the accuracy of intraoral scanning for complete-arch implant restorations using an implant index cast (The Glossary of Prosthodontic Terms 9th Edition) and a three-dimensional printed cast. A clinical case of immediate loading on a maxillary edentulous patient illustrates the application of an implant index cast in implant fixed complete dentures (IFCDs).

Hydrophilic titanium surface modulates early stages of osseointegration in osteoporosis.

Objective: Using a mouse osteoporotic model, this study aimed to determine the influence of hydrophilic titanium surfaces on gene expression and bone formation during the osseointegration process.

Background: Based on the previous evidence, it is plausible to assume that osteoporotic bone has a different potential of bone healing. Therefore, implant surface modification study that aims at enhancing bone formation to further improve short- and long-term clinical outcomes in osteoporosis is necessary.

Denture scanning technique for computer-guided implant-supported restoration treatment of edentulous patients.

The traditional protocol for guided surgery in a completely edentulous patient is time-consuming, requiring the fabrication of a radiographic guide and a dual cone beam computed tomography (CBCT) scan. Using intraoral scanners to scan the edentulous ridge and the existing denture has been advocated to simplify the process. This technique offers a versatile, precise, and predictable method for the digital planning workflow in edentulous patients for either a fixed or removable restoration.

Influence of operator experience, scanner type, and scan size on 3D scans.

Statement Of Problem: Intraoral scanners (IOSs) have some inherent distortions caused by optical and/or software imperfections. However, how other factors such as operator experience, scan time, scanner type, and scan size influence scan accuracy is not clear.

Purpose: The purpose of this in vitro study was to evaluate the trueness and precision of scans performed by 3 professionals with different levels of experience by using 2 IOSs.

A long-term evaluation of experimental potassium oxalate concentrations on dentin hypersensitivity reduction: A triple-blind randomized clinical trial.

Objective: The aim of this split-mouth, triple-blind, randomized clinical trial was to evaluate the long-term clinical efficacy of experimental potassium oxalate concentration (10%) in relieving dentin hypersensitivity (DH), after a four-session application protocol.

Methods: Potassium oxalate gels with different concentrations (5 and 10%) were randomly assigned to half of the 31 patients from the sample in a split-mouth design. The desensitizers were applied following a four-session protocol, one session every 48 h.

Four-Session Protocol Effectiveness in Reducing Cervical Dentin Hypersensitivity: A 24-Week Randomized Clinical Trial.

A single-blind randomized clinical trial was conducted to evaluate the effectiveness of desensitizing agents with different action mechanisms in reducing cervical dentin hypersensitivity (CDH) after four application sessions, with 24-week follow-up. Sixty patients with CDH were selected in the study and were allocated in three groups of treatment: Desensibilize KF 2%, Clinpro XT Varnish, and Photon Lase III (100 mW, 4 J/cm-1 J/cm each point, 10 sec per point with wavelength of 808 nm). There were four application sessions performed, with a 48-h interval between each one.