Mechanical thrombectomy for acute pulmonary embolism in lung transplant recipients.

The rates of pulmonary embolism (PE) are high among lung transplant (LT) recipients. Management is challenging because of elevated bleeding risks and inadequacy of conventional PE risk stratification tools. New percutaneous large bore mechanical thrombectomy catheters are being increasingly used effectively to debulk thrombus and restore flow immediately.

Coated and uncoated cellophane as materials for microplates and open-channel microfluidics devices.

This communication describes the use of uncoated cellophane (regenerated cellulose films) for the fabrication of microplates, and the use of coated cellophane for the fabrication of open-channel microfluidic devices. The microplates based on uncoated cellophane are particularly interesting for applications that require high transparency in the ultraviolet (UV) regime, and offer a low-cost alternative to expensive quartz-well plates. Uncoated cellophane is also resistant to damage by various solvents.

Paper-Based Electrical Respiration Sensor.

Current methods of monitoring breathing require cumbersome, inconvenient, and often expensive devices; this requirement sets practical limitations on the frequency and duration of measurements. This article describes a paper-based moisture sensor that uses the hygroscopic character of paper (i.e.

Wavelength selection of rippling patterns in myxobacteria.

Rippling patterns of myxobacteria appear in starving colonies before they aggregate to form fruiting bodies. These periodic traveling cell density waves arise from the coordination of individual cell reversals, resulting from an internal clock regulating them and from contact signaling during bacterial collisions. Here we revisit a mathematical model of rippling in myxobacteria due to Igoshin et al.

Analytical Devices Based on Direct Synthesis of DNA on Paper.

This paper addresses a growing need in clinical diagnostics for parallel, multiplex analysis of biomarkers from small biological samples. It describes a new procedure for assembling arrays of ssDNA and proteins on paper. This method starts with the synthesis of DNA oligonucleotides covalently linked to paper and proceeds to assemble microzones of DNA-conjugated paper into arrays capable of simultaneously capturing DNA, DNA-conjugated protein antigens, and DNA-conjugated antibodies.

Electroanalytical devices with pins and thread.

This work describes the adaptive use of conventional stainless steel pins-used in unmodified form or coated with carbon paste-as working, counter, and quasi-reference electrodes in electrochemical devices fabricated using cotton thread or embossed omniphobic R(F) paper to contain the electrolyte and sample. For some applications, these pin electrodes may be easier to modify and use than printed electrodes, and their position and orientation can be changed as needed. Electroanalytical devices capable of multiplex analysis (thread-based arrays or 96-well plates) were easily fabricated using pins as electrodes in either thread or omniphobic R(F) paper.

Folding analytical devices for electrochemical ELISA in hydrophobic R(H) paper.

This work describes a device for electrochemical enzyme-linked immunosorbent assay (ELISA) designed for low-resource settings and diagnostics at the point of care. The device is fabricated entirely in hydrophobic paper, produced by silanization of paper with decyl trichlorosilane, and comprises two zones separated by a central crease: an embossed microwell, on the surface of which the antigen or antibody immobilization and recognition events occur, and a detection zone where the electrodes are printed. The two zones are brought in contact by folding the device along this central crease; the analytical signal is recorded from the folded configuration.

Inkjet printing of conductive inks with high lateral resolution on omniphobic "R(F) paper" for paper-based electronics and MEMS.

The use of omniphobic "fluoroalkylated paper" as a substrate for inkjet printing of aqueous inks that are the precursors of electrically conductive patterns is described. By controlling the surface chemistry of the paper, it is possible to print high resolution, conductive patterns that remain conductive after folding and exposure to common solvents.

Rapid fabrication of pressure-driven open-channel microfluidic devices in omniphobic R(F) paper.

This paper describes the fabrication of pressure-driven, open-channel microfluidic systems with lateral dimensions of 45-300 microns carved in omniphobic paper using a craft-cutting tool. Vapor phase silanization with a fluorinated alkyltrichlorosilane renders paper omniphobic, but preserves its high gas permeability and mechanical properties. When sealed with tape, the carved channels form conduits capable of guiding liquid transport in the low-Reynolds number regime (i.

Cell encapsulation in sub-mm sized gel modules using replica molding.

For many types of cells, behavior in two-dimensional (2D) culture differs from that in three-dimensional (3D) culture. Among biologists, 2D culture on treated plastic surfaces is currently the most popular method for cell culture. In 3D, no analogous standard method--one that is similarly convenient, flexible, and reproducible--exists.