Discussion and Demonstration of RF-MEMS Attenuators Design Concepts and Modules for Advanced Beamforming in the Beyond-5G and 6G Scenario-Part 2.

In this paper, different concepts of reconfigurable RF-MEMS attenuators for beamforming applications are proposed and critically assessed. Capitalizing on the previous part of this work, the 1-bit attenuation modules featuring series and shunt resistors and low-voltage membranes (7-9 V) are employed to develop a 3-bit attenuator for fine-tuning attenuations (<-10 dB) in the 24.25-27.

Discussion and Demonstration of RF-MEMS Attenuators Design Concepts and Modules for Advanced Beamforming in the Beyond-5G and 6G Scenario-Part 1.

This paper describes different variants of broadband and simple attenuator modules for beamforming applications, based on radio frequency micro electro-mechanical systems (RF-MEMS), framed within coplanar waveguide (CPW) structures. The modules proposed in the first part of this work differ in their actuation voltage, topology, and desired attenuation level. Fabricated samples of basic 1-bit attenuation modules, characterized by a moderate footprint of 690 × 1350 µm and aiming at attenuation levels of -2, -3, and -5 dB in the 24.

MEMS-Switched Triangular and U-Shaped Band-Stop Resonators for K-Band Operation.

Triangular resonators re-shaped into Sierpinski geometry and U-shaped resonators were designed, linking them with single-pole-double-through (SPDT) RF MEMS switches to provide frequency tuning for potential applications in the K-Band. Prototypes of band-stop narrowband filters working around 20 GHz and 26 GHz, interesting for RADAR and satellite communications, were studied in a coplanar waveguide (CPW) configuration, and the tuning was obtained by switching between two paths of the devices loaded with different resonators. As a result, dual-band operation or fine-tuning could be obtained depending on the choice of the resonator, acting as a building block.

Triangular Sierpinski Microwave Band-Stop Resonators for K-Band Filtering.

Triangular resonators re-shaped with Sierpinski geometry were designed, manufactured, and tested for potential applications in the K-Band. Prototypes of band-stop filters working around 20 GHz and 26 GHz, interesting for RADAR and satellite communications, were studied in a coplanar waveguide (CPW) configuration. Single and coupled structures were analyzed to give evidence for: (i) the tuning of the resonance frequency by increasing the internal complexity of the triangle and (ii) resonance enhancement when coupled structures are considered.

Fabrication of Ultra-Sharp Tips by Dynamic Chemical Etching Process for Scanning Near-Field Microwave Microscopy.

This work details an effective dynamic chemical etching technique to fabricate ultra-sharp tips for Scanning Near-Field Microwave Microscopy (SNMM). The protruded cylindrical part of the inner conductor in a commercial SMA (Sub Miniature A) coaxial connector is tapered by a dynamic chemical etching process using ferric chloride. The technique is optimized to fabricate ultra-sharp probe tips with controllable shapes and tapered down to have a radius of tip apex around ∼1 μm.

Design of U-Shaped Frequency Tunable Microwave Filters in MEMS Technology.

U-shaped microwave resonators implemented by RF MEMS switches can be considered the result of a novel design approach for obtaining small-footprint tunable resonators, owing to the bent shape of the resonator and the microsystem solution for changing the frequency of resonance. In this paper, we discuss the design approach for potential configurations of U-shaped structures combined with ohmic RF MEMS switches. Owing to their prospective application in RADAR and satellite systems, the devices were assessed for K-Band operation, specifically for 15 GHz, 20 GHz, and 26 GHz.

A broadband toolbox for scanning microwave microscopy transmission measurements.

In this paper, we present in detail the design, both electromagnetic and mechanical, the fabrication, and the test of the first prototype of a Scanning Microwave Microscope (SMM) suitable for a two-port transmission measurement, recording, and processing the high frequency transmission scattering parameter S21 passing through the investigated sample. The S21 toolbox is composed by a microwave emitter, placed below the sample, which excites an electromagnetic wave passing through the sample under test, and is collected by the cantilever used as the detector, electrically matched for high frequency measurements. This prototype enhances the actual capability of the instrument for a sub-surface imaging at the nanoscale.